Brake Temps at the track

DarkJak

What are folks getting for brake temps at the track, and how does that translate to fluid temps?

I've been fighting high brake temps at the track for my last few events.
The latest has been installing the Stillen brake duct kit. So currently I'm running Castrol SRF fluid, Project Mu HC800 pads, Z1 2 piece rotors, and the brake duct kit. This is with the sport pack's akebonos.

Last of 3 sessions got up to 850F measuring the swept section of the rotor, and had my brakes smoking plus calipers leaking fluid from the bleeders. The pedal still felt consistent, although had a bit more travel, and I didn't feel much brake fade.

What other steps have you taken to cool brakes?

__________________
@stupidtoycars | My track vids
09 7AT|MCS 2WNR|Topgunz Rotrex|Ecutek (Eugene)|Maxxis RC1|Titan-7 TS-5|OSG LSD|Rear Mount Derale Oil Cooler (WIP)+25 Trans Cooler|Fismo|G-LOC R12/R10|Zeta III L|NLR Wing and Splitter|CJM Pan and Fuel Hat|Radium Surge Tank|AP Racing CP9668

Rusty

Hard Brakes Ti heat shield shims between the front pads and pistons.

https://hardbrakes.com/index.php?mai...roducts_id=106

Might have to go to a larger 3" cooling hose.

You are not the only one to have the bleeder screws leak fluid when the Akebono's get hot.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

RN SHARK

At least your pedal hasn’t gone soft yet like mine has at Carolina Motorsports Park. Not enough straights to cool them down.

__________________
___________
'09 6sp/Z1/PowerTrix/SPL/Swift/SRP/Whiteline/F.I.LTH&CBE/UpRev by Seb/CJM/Stillen/Ings+1/RJM/TrackSpec/Sparco/Motul/Wavetrac/Coolerworx/Verus/CraftSquare
'14 SRT Grand Cherokee; '08 TL Type-S

DarkJak

Thanks, I'll be getting a set before next track day. Would you recommend going with the 1mm or were the .5mm shields adequate for you?

__________________
@stupidtoycars | My track vids
09 7AT|MCS 2WNR|Topgunz Rotrex|Ecutek (Eugene)|Maxxis RC1|Titan-7 TS-5|OSG LSD|Rear Mount Derale Oil Cooler (WIP)+25 Trans Cooler|Fismo|G-LOC R12/R10|Zeta III L|NLR Wing and Splitter|CJM Pan and Fuel Hat|Radium Surge Tank|AP Racing CP9668

Rusty

I got the .5mm shims. Because the thickness of pads are not the same from manufacturer to manufacturer. The 1.mm might fit one set of pads, and not a set of someone else. If you plan to stick with one set of pads. The try the 1.mm shim.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

DarkJak

Will be trying to source them, as soon as I can get an order working on their site.

BTW, I notice you plus most folks run XP10/8 staggered pads. Do XP10's all around cause too much instability/ice mode?

__________________
@stupidtoycars | My track vids
09 7AT|MCS 2WNR|Topgunz Rotrex|Ecutek (Eugene)|Maxxis RC1|Titan-7 TS-5|OSG LSD|Rear Mount Derale Oil Cooler (WIP)+25 Trans Cooler|Fismo|G-LOC R12/R10|Zeta III L|NLR Wing and Splitter|CJM Pan and Fuel Hat|Radium Surge Tank|AP Racing CP9668

Hotrodz

I run APR ducts, Stillen brake and tire brake shields. I'm not sure what thickness any more and my rotor temps are less than half of yours with carbotech 10x8.

But I'm slow according to Rusty!

Sent from my SM-G965U using Tapatalk

__________________
Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:|Fast Intentions 3" TT-TDX|SpecialtyZ/Fast Intentions 72 Row Oil Cooler|SZ 6 Puck Clutch & Flywheel|3GsCustoms|Z1|Wavetrac|Hotchkis|Whiteline |Blitz|Fortune Auto 500|Fujimura|SPL|H&R|TK|TWM|RPM Rollbar|Sparco|Next Level Performance|TrackSpec|AeroFlow Dynamics|Pioneer|

Rusty

Ah, got you up to fast turtle now.

Run the XP10/XP8 because of the brake balance. There is too much brake in the rear.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html