Installing z1 intake manifold

jamesj1996 · 09-30-2014, 03:24 PM

how many pounds do the lugs need to torqued to? i tried downloading the manual but my computer wont let me open it...can someone find out for me

wanker · 09-30-2014, 03:27 PM

E-mail Z1 directly. They are very good at answering questions, usually within 24 hours.

exsanity · 09-30-2014, 03:32 PM

I would say that it is the same as the torque required on the stock manifold.

jamesj1996 · 09-30-2014, 03:39 PM

yeah but idk that...and when i called they jus sent me the manual which i cant open

Chuck33079 · 09-30-2014, 04:03 PM

There's a link to the factory service manual available on this site.

exsanity · 09-30-2014, 05:17 PM

Disclaimer: The following information is intended for reference material only. Refer to the Service Data and Specifications table "Tightening Torque" in the EM section of the applicable Factory Service Manual for your model year Z.

Quote:

Originally Posted by Service Manual

INTAKE MANIFOLD COLLECTOR
• If stud bolts were removed, install them and tighten to the torque specified below.

: 10.8 N·m (1.1 kg-m, 8 ft-lb)

• Tighten mounting bolts and nuts in numerical order as shown in the
figure.

As found in >this< post.

jamesj1996 · 09-30-2014, 05:20 PM

Quote:

Originally Posted by exsanity

Disclaimer: The following information is intended for reference material only. Refer to the Service Data and Specifications table "Tightening Torque" in the EM section of the applicable Factory Service Manual for your model year Z.

As found in >this< post.

thanks so much and whats the order it needs to be in can u post a pic?

jamesj1996 · 09-30-2014, 05:29 PM

nvm got it

kornflake7 · 09-30-2014, 06:18 PM

its basically hand tight 8 ft lb is basically nothing if you do too much it can cause problems, it was the same way when installing spacer on my old 350

ANMVQ · 09-30-2014, 09:55 PM

I just followed the hand tight rule , I recheked after two days to make sure also.

2012z · 10-01-2014, 07:38 PM

Quote:

Originally Posted by jamesj1996

how many pounds do the lugs need to torqued to? i tried downloading the manual but my computer wont let me open it...can someone find out for me

I am very interested in gains you pick up from this intake....please provide feedback once u get installed if u can. Thanks

ANMVQ · 10-02-2014, 08:12 AM

its there, WTQ is up I made some runs a few weeks back, Wasn't happy about the place cause they didn't set the dyno up for AWD and almost blew my tcase.

09-30-2014, 03:24 PM	#1 (permalink)
jamesj1996 Enthusiast Member Join Date: Apr 2014 Location: new jersey Posts: 291 Drives: 2009 370z cp sport Rep Power: 11	Installing z1 intake manifold how many pounds do the lugs need to torqued to? i tried downloading the manual but my computer wont let me open it...can someone find out for me

09-30-2014, 04:03 PM	#5 (permalink)
Chuck33079 A True Z Fanatic Join Date: Nov 2011 Location: Houston Posts: 12,265 Drives: 2011 370ztt Rep Power: 29539	There's a link to the factory service manual available on this site. abm89 likes this. __________________ 2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

09-30-2014, 09:55 PM	#10 (permalink)
ANMVQ A True Z Fanatic Join Date: Mar 2011 Location: Framingham MA Posts: 2,732 Drives: 2014 Q50 AWD Rep Power: 19	I just followed the hand tight rule , I recheked after two days to make sure also. __________________ 14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

10-02-2014, 08:12 AM	#12 (permalink)
ANMVQ A True Z Fanatic Join Date: Mar 2011 Location: Framingham MA Posts: 2,732 Drives: 2014 Q50 AWD Rep Power: 19	its there, WTQ is up I made some runs a few weeks back, Wasn't happy about the place cause they didn't set the dyno up for AWD and almost blew my tcase. __________________ 14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Upper Intake Manifold	DIGItonium	Forced Induction	10	12-03-2013 04:56 PM
ID this intake manifold	Japanjay	Intake/Exhaust	5	07-27-2013 08:31 PM
[FOR SALE] OEM intake manifold	seymore4	Parts for sale (Private Classifieds)	5	02-24-2012 07:17 PM
Motordyne Intake Manifold on the way!!	GZ3	Intake/Exhaust	67	09-16-2010 01:49 AM
Revshift Intake Manifold	Jamaica	Intake/Exhaust	22	07-14-2010 12:34 AM

09-30-2014, 03:27 PM	#2 (permalink)
wanker Enthusiast Member Join Date: Apr 2014 Location: San Diego Posts: 443 Drives: 2011 370Z S/T A7 Rep Power: 2901	E-mail Z1 directly. They are very good at answering questions, usually within 24 hours.

09-30-2014, 03:32 PM	#3 (permalink)
exsanity Premium Member Join Date: Oct 2013 Location: Middle Tennessee Posts: 10,499 Drives: you mad.. Rep Power: 3700	I would say that it is the same as the torque required on the stock manifold.

09-30-2014, 03:39 PM	#4 (permalink)
jamesj1996 Enthusiast Member Join Date: Apr 2014 Location: new jersey Posts: 291 Drives: 2009 370z cp sport Rep Power: 11	yeah but idk that...and when i called they jus sent me the manual which i cant open

09-30-2014, 05:29 PM	#8 (permalink)
jamesj1996 Enthusiast Member Join Date: Apr 2014 Location: new jersey Posts: 291 Drives: 2009 370z cp sport Rep Power: 11	nvm got it

09-30-2014, 06:18 PM	#9 (permalink)
kornflake7 Base Member Join Date: Mar 2014 Location: San Antonio, TX Posts: 233 Drives: 2013 Nismo 370z Rep Power: 11	its basically hand tight 8 ft lb is basically nothing if you do too much it can cause problems, it was the same way when installing spacer on my old 350