Issues with

Tusharp83 · 05-12-2018, 03:44 PM

My Mods: Stillen Supercharger.

I'm having lot of issues with CEL. Throttle acting weird. Get CEL with P0172 and P0175. I have changed out the camshaft sensor and crankshaft sensor already. I've been watching the the gauge on how much fuel is adding and cutting. Everytime I make hard turn or go over a bump my car goes rich. Car idles weird. Comes to stop and car dies sometime. Car takes really long to start after it dies on the road. Make things even worse somebody yelled "GET A FORD" LMFAO. Started looking around the issues and only thing I found is this pipe is squeezed up by the the throttle body. Can this be issue causing all the problems I'm having.

Bikeracer1098 · 05-12-2018, 06:19 PM

Had the same issues and same error codes with my car 2 weeks ago.

Initially it was just PO172 which I cleared twice then PO172 & PO175 which I cleared.

However hasn’t happened since.

A few issues with my Stillen supercharger

Tusharp83 · 05-12-2018, 11:44 PM

Looks like that was the problem. I used the zip tie and pull that pipe and strapped it with strut bar and drove around no problem. Weird I didn’t know little evap pipe be causing all the error codes.

turtle64b · 05-13-2018, 07:03 AM

A better way to route that is under the throttle body there. It'll let the tube bend a little more gentle.

Tusharp83 · 05-13-2018, 10:26 AM

That is my plan just wanted to confirm that it was the problem. That’s why I went ghetto on it.

Bikeracer1098 · 05-13-2018, 02:30 PM

I you sure that this is the cause of the problem as I had exactly the same problems with my car which now seems to have cleared.

Checked the same pipe on mine and it seems fine.

Could the problem be faulty Stillen extension MAF cables which cause an intermittent problem?

Tusharp83 · 05-13-2018, 08:16 PM

Well it could be MAF extension cable. I wrapped the wire with heat shield. Because it’s too damn hot for n the engine bay. When I was trying to solve my problem I made sure I did that part first. It solved the weird idle problem. Then car keep running rich on normal driving and because ecu was trying cut so much fuel I knew I had problem else where then I discover the squeeze pipe and it solved the problem.

Nismo0583 · 07-08-2022, 09:57 PM

wonder has this issue been solved. now having this issue with my stock nismo. smh this thing does this like every other few months, so damn weird. I end up swapping MAF's out because on my ecutek logs the passenger (bank 1) voltage is like .30 while driver is .70-1.00. hoping someone has solved this lol.

Optimiser · 07-09-2022, 02:44 AM

Quote:

Originally Posted by Bikeracer1098

I you sure that this is the cause of the problem as I had exactly the same problems with my car which now seems to have cleared.

Checked the same pipe on mine and it seems fine.

Could the problem be faulty Stillen extension MAF cables which cause an intermittent problem?

Most likely yes.

05-12-2018, 03:44 PM	#1 (permalink)
Tusharp83 Base Member Join Date: Aug 2016 Location: Pigeon Forge, TN Posts: 82 Drives: 2009 370z Black 6MT Rep Power: 9	Issues with My Mods: Stillen Supercharger. I'm having lot of issues with CEL. Throttle acting weird. Get CEL with P0172 and P0175. I have changed out the camshaft sensor and crankshaft sensor already. I've been watching the the gauge on how much fuel is adding and cutting. Everytime I make hard turn or go over a bump my car goes rich. Car idles weird. Comes to stop and car dies sometime. Car takes really long to start after it dies on the road. Make things even worse somebody yelled "GET A FORD" LMFAO. Started looking around the issues and only thing I found is this pipe is squeezed up by the the throttle body. Can this be issue causing all the problems I'm having.

05-12-2018, 06:19 PM	#2 (permalink)
Bikeracer1098 Base Member Join Date: Dec 2017 Location: Camberley Posts: 59 Drives: Porsche 997.2 turbo Rep Power: 7	Had the same issues and same error codes with my car 2 weeks ago. Initially it was just PO172 which I cleared twice then PO172 & PO175 which I cleared. However hasn’t happened since. A few issues with my Stillen supercharger __________________ Last edited by Bikeracer1098; 05-12-2018 at 06:24 PM.

05-12-2018, 11:44 PM	#3 (permalink)
Tusharp83 Base Member Join Date: Aug 2016 Location: Pigeon Forge, TN Posts: 82 Drives: 2009 370z Black 6MT Rep Power: 9	Looks like that was the problem. I used the zip tie and pull that pipe and strapped it with strut bar and drove around no problem. Weird I didn’t know little evap pipe be causing all the error codes. Last edited by Tusharp83; 05-12-2018 at 11:52 PM.

05-13-2018, 02:30 PM	#6 (permalink)
Bikeracer1098 Base Member Join Date: Dec 2017 Location: Camberley Posts: 59 Drives: Porsche 997.2 turbo Rep Power: 7	I you sure that this is the cause of the problem as I had exactly the same problems with my car which now seems to have cleared. Checked the same pipe on mine and it seems fine. Could the problem be faulty Stillen extension MAF cables which cause an intermittent problem? Optimiser likes this. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ac issues?	Z_ealot	Nissan 370Z General Discussions	25	08-17-2016 11:25 PM
Need help on possible issues	birdman71	Engine & Drivetrain	9	09-27-2015 01:07 PM
CSC issues	Djc-40thZ	40th Anniversary 370Z	2	06-08-2015 09:00 PM
thinking of buying 370z, then GTM turbo's , but overheat issues,oil issues ??	Christopher	Nissan 370Z General Discussions	19	10-16-2009 04:55 PM
Initial Z issues that are now non-issues......	cave vulture	Nissan 370Z General Discussions	1	09-06-2009 11:19 PM

05-13-2018, 10:26 AM	#5 (permalink)
Tusharp83 Base Member Join Date: Aug 2016 Location: Pigeon Forge, TN Posts: 82 Drives: 2009 370z Black 6MT Rep Power: 9	That is my plan just wanted to confirm that it was the problem. That’s why I went ghetto on it.

05-13-2018, 08:16 PM	#7 (permalink)
Tusharp83 Base Member Join Date: Aug 2016 Location: Pigeon Forge, TN Posts: 82 Drives: 2009 370z Black 6MT Rep Power: 9	Well it could be MAF extension cable. I wrapped the wire with heat shield. Because it’s too damn hot for n the engine bay. When I was trying to solve my problem I made sure I did that part first. It solved the weird idle problem. Then car keep running rich on normal driving and because ecu was trying cut so much fuel I knew I had problem else where then I discover the squeeze pipe and it solved the problem.

07-08-2022, 09:57 PM	#8 (permalink)
Nismo0583 Base Member Join Date: Oct 2021 Location: Florida Posts: 47 Drives: 12 Nissan 370z NISMO Rep Power: 4	wonder has this issue been solved. now having this issue with my stock nismo. smh this thing does this like every other few months, so damn weird. I end up swapping MAF's out because on my ecutek logs the passenger (bank 1) voltage is like .30 while driver is .70-1.00. hoping someone has solved this lol.