Z1 Seat Rails - removed planted rails

Corsairprime · 01-01-2022, 09:19 AM

Hi Z fans.

I just wanted to relate that recently I traded my planted seat rails for the Z1 seat rail mounts. It was well worth the effort in my view. The side mounts by Z1, see Link: Z1 Seat Rails for the 370, are superior in the fact that the side mount seat rails mount lower in the car to start with and are alot less of a fuss to setup. You should buy at least one hardware kit when you pickup your rails. It'll be good enough for both sides of the car. I first swapped out my factory seats for Sparco Evo XL QRT seats and tried to make the Planted mounts work along with the Sparco side mounts. This forces the seatbase to start out 1.5" to 2" higher on both sides of the cabin. If you use a slider, even more. Well if you track your car like I do then every inch of headroom is precious. Swapping to the Z1 seat rails gives you back the room you need on both sides of the car for adequate helmet clearance be it a passenger or DE instructor.

The passenger seat mounted with Planted Seat Rails, sliders and Sparco side mounts.

Same seat on Z1 Seat rails.

Sorry for the sideways view of the second image. But the real indication of success is the lower front right part of the seat. It sits quite a bit lower with only one seat mount needed instead of two or three.

PM me if you have questions or want to see other images. I'll take more pictures if you need me to.

NOTE: The hardware spacer count on the door side rear mount is key. You only need them in this one location on each side of the car, no other location requires them. One larger inside and one medium outside the Z1 rail. But only in that location on each side of the car.

OptionZero · 01-01-2022, 12:35 PM

Good to know it works on the EVO XL
Z1’s listing says its only up to 465mm wide seats and i thought the Evo Was wider

Corsairprime · 01-01-2022, 03:39 PM

A better picture comparison of the difference between the Planted mount and the Z1 Mount from the passenger side of the cabin.

Planted:

Z1 Seat Rail:

Corsairprime · 01-01-2022, 03:46 PM

Regarding the size of the seat I have from Sparco.

See the chart, Not sure if this dimension info helps, but I am using the largest seat they sell with this Z1 Mount and it works just fine. Props to Z1 for creating a workable seat mount system for side mount seats. The hardware kit is critical in helping to adapt these mounts to fit your seat. I ordered one just in case and I am glad that I did.

The Sparco Seat Size Chart:

OptionZero · 01-01-2022, 05:34 PM

I’ll be using a Sparco Evo II which is listed at 535mm so it should work

Corsairprime · 01-03-2022, 09:18 AM

I would be interested to see who else has used these side-mount Z1 seat rails to mount seat in their Zs. Post your pics here. So far I am very happy with the results.

Hotrodz · 01-03-2022, 11:47 AM

I had my Evo II seat mounted to a Wedge Engineering seat mount and had to ditch the rails. I bought the Z1 side mounts for the passenger side and will be fix mounting the passenger seat. I don't like sliders for a track car unless OEM. Just my two cents. I do like the simplicity of Z1 mounts. My driver's is a custom mount but if I don't like it I may go with the Z1 side mount.

Sent from my SM-G965U using Tapatalk

mara · 02-01-2022, 06:59 AM

Do you mind telling us how tall you are and what sort of head clearance you are getting with a helmet on.
Also does your sparco seating position sit lower then oem seat. Reason im asking as im 6"2 and looking at getting a set or seats so i can fit in the car with a helmet on. (Tall ppl problems)

Hotrodz · 02-01-2022, 09:09 AM

Quote:

Originally Posted by mara

Do you mind telling us how tall you are and what sort of head clearance you are getting with a helmet on.
Also does your sparco seating position sit lower then oem seat. Reason im asking as im 6"2 and looking at getting a set or seats so i can fit in the car with a helmet on. (Tall ppl problems)

I am 6'1" and have a long upper torso. With the Wedge Engineering bracket I was fine without the seat rail. The Z1 seat bracket should sit even lower.

Sent from my SM-G965U using Tapatalk

Corsairprime · 02-01-2022, 10:32 AM

Quote:

Originally Posted by mara

Do you mind telling us how tall you are and what sort of head clearance you are getting with a helmet on.
Also does your sparco seating position sit lower then oem seat. Reason im asking as im 6"2 and looking at getting a set or seats so i can fit in the car with a helmet on. (Tall ppl problems)

Hey I am 6'2" as well. The single mount option offered by Z1 lowered the drivers seat by about 1.5" to 2" and the passenger even more(no slider). I'll measure the precise amount of clearance I currently have with the new mounts from Z1. I was using the planted mounts along with the Sparco Side rails. It seems to be lower to my view. The change in height is noticeable because I have to work a bit harder to see curb lines when turning sharper to avoid the potential for curbing my rims. I'll update this thread again shortly.

mara · 02-01-2022, 09:22 PM

Quote:

Originally Posted by Corsairprime

Hey I am 6'2" as well. The single mount option offered by Z1 lowered the drivers seat by about 1.5" to 2" and the passenger even more(no slider). I'll measure the precise amount of clearance I currently have with the new mounts from Z1. I was using the planted mounts along with the Sparco Side rails. It seems to be lower to my view. The change in height is noticeable because I have to work a bit harder to see curb lines when turning sharper to avoid the potential for curbing my rims. I'll update this thread again shortly.

Nice to know.
I actually have a set of buddy club rails on order right now.
so fingers crossed they do the job.

good to see more pics/vid if you have the time.

Hotrodz · 02-01-2022, 11:12 PM

Quote:

Originally Posted by mara

Nice to know.

I actually have a set of buddy club rails on order right now.

so fingers crossed they do the job.

good to see more pics/vid if you have the time.

Return them! Others have issues with getting their seat to sit straight and they can be a little wonky!

Sent from my SM-G965U using Tapatalk

Corsairprime · 02-02-2022, 08:41 AM

Quote:

Originally Posted by Corsairprime

Hey I am 6'2" as well. The single mount option offered by Z1 lowered the drivers seat by about 1.5" to 2" and the passenger even more(no slider). I'll measure the precise amount of clearance I currently have with the new mounts from Z1. I was using the planted mounts along with the Sparco Side rails. It seems to be lower to my view. The change in height is noticeable because I have to work a bit harder to see curb lines when turning sharper to avoid the potential for curbing my rims. I'll update this thread again shortly.

Ok guys, I have measured the clearance in the driver's seat with my helmet on and the race belts secured. I have about 1.5" clearance to the headliner from my helmet crown. For me this is about two fingers width. Depending on how I tilt my head forward or back it can drop to 3/4", still quite roomy for a track day appearance. I did not measure the passenger side for clearance but will update this thread with the same information as I have the helmet with me today. I expect it might be similar to the drivers side clearance. Details to follow.

What variety of pictures would you like. Let me know and I'll get them together.

rspray2000 · 02-02-2022, 06:20 PM

Quote:

Originally Posted by Corsairprime

Ok guys, I have measured the clearance in the driver's seat with my helmet on and the race belts secured. I have about 1.5" clearance to the headliner from my helmet crown. For me this is about two fingers width. Depending on how I tilt my head forward or back it can drop to 3/4", still quite roomy for a track day appearance. I did not measure the passenger side for clearance but will update this thread with the same information as I have the helmet with me today. I expect it might be similar to the drivers side clearance. Details to follow.

What variety of pictures would you like. Let me know and I'll get them together.

I’m 6’2” and wonder if these would enable me to clear the “broomstick test” in my roadster…

Corsairprime · 02-03-2022, 10:58 AM

Ok, I did the same fingers above the Helmet test on the passenger seat. The clearance measurement for me is the same as the drivers seat. I get 2 fingers above the crown of the helmet. Two fingers translates to 1.5" at a maximum to the headliner in my Z. You definitely sit lower in the car. It is interesting to note without the helmet, I'd say there is about 3.5" to 4" from the top of my head to the headliner. It feels very roomy for a car with racing seats and 5 point harnesses.

01-01-2022, 09:19 AM	#1 (permalink)
Corsairprime Base Member Join Date: May 2014 Location: Frisco, TX Posts: 215 Drives: 14 370Z Nismo GM 6MT Rep Power: 3545	Z1 Seat Rails - removed planted rails Hi Z fans. I just wanted to relate that recently I traded my planted seat rails for the Z1 seat rail mounts. It was well worth the effort in my view. The side mounts by Z1, see Link: Z1 Seat Rails for the 370, are superior in the fact that the side mount seat rails mount lower in the car to start with and are alot less of a fuss to setup. You should buy at least one hardware kit when you pickup your rails. It'll be good enough for both sides of the car. I first swapped out my factory seats for Sparco Evo XL QRT seats and tried to make the Planted mounts work along with the Sparco side mounts. This forces the seatbase to start out 1.5" to 2" higher on both sides of the cabin. If you use a slider, even more. Well if you track your car like I do then every inch of headroom is precious. Swapping to the Z1 seat rails gives you back the room you need on both sides of the car for adequate helmet clearance be it a passenger or DE instructor. The passenger seat mounted with Planted Seat Rails, sliders and Sparco side mounts. Same seat on Z1 Seat rails. Sorry for the sideways view of the second image. But the real indication of success is the lower front right part of the seat. It sits quite a bit lower with only one seat mount needed instead of two or three. PM me if you have questions or want to see other images. I'll take more pictures if you need me to. NOTE: The hardware spacer count on the door side rear mount is key. You only need them in this one location on each side of the car, no other location requires them. One larger inside and one medium outside the Z1 rail. But only in that location on each side of the car. OptionZero likes this. __________________ Corsairprime 2014 Nismo #462, GunMetal Grey, GT-R Start Button, AAM S-Line/R-Line intake and S-Line exhaust, Berk HFCs, Osiris Tuned at JoTech Last edited by Corsairprime; 01-01-2022 at 03:31 PM.

01-01-2022, 12:35 PM	#2 (permalink)
OptionZero A True Z Fanatic Join Date: Apr 2011 Location: Sacramento Posts: 3,235 Drives: 15 370Z Nismo 6MT Rep Power: 214100	Good to know it works on the EVO XL Z1’s listing says its only up to 465mm wide seats and i thought the Evo Was wider Corsairprime likes this. __________________ OptionZero Build Thread

01-01-2022, 03:39 PM	#3 (permalink)
Corsairprime Base Member Join Date: May 2014 Location: Frisco, TX Posts: 215 Drives: 14 370Z Nismo GM 6MT Rep Power: 3545	A better picture comparison of the difference between the Planted mount and the Z1 Mount from the passenger side of the cabin. Planted: Z1 Seat Rail: __________________ Corsairprime 2014 Nismo #462, GunMetal Grey, GT-R Start Button, AAM S-Line/R-Line intake and S-Line exhaust, Berk HFCs, Osiris Tuned at JoTech

01-01-2022, 03:46 PM	#4 (permalink)
Corsairprime Base Member Join Date: May 2014 Location: Frisco, TX Posts: 215 Drives: 14 370Z Nismo GM 6MT Rep Power: 3545	The dimensions of the Sparco EVO XL QRT Regarding the size of the seat I have from Sparco. See the chart, Not sure if this dimension info helps, but I am using the largest seat they sell with this Z1 Mount and it works just fine. Props to Z1 for creating a workable seat mount system for side mount seats. The hardware kit is critical in helping to adapt these mounts to fit your seat. I ordered one just in case and I am glad that I did. The Sparco Seat Size Chart: __________________ Corsairprime 2014 Nismo #462, GunMetal Grey, GT-R Start Button, AAM S-Line/R-Line intake and S-Line exhaust, Berk HFCs, Osiris Tuned at JoTech

01-03-2022, 09:18 AM	#6 (permalink)
Corsairprime Base Member Join Date: May 2014 Location: Frisco, TX Posts: 215 Drives: 14 370Z Nismo GM 6MT Rep Power: 3545	I would be interested to see who else has used these side-mount Z1 seat rails to mount seat in their Zs. Post your pics here. So far I am very happy with the results. mara likes this. __________________ Corsairprime 2014 Nismo #462, GunMetal Grey, GT-R Start Button, AAM S-Line/R-Line intake and S-Line exhaust, Berk HFCs, Osiris Tuned at JoTech

01-03-2022, 11:47 AM	#7 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	I had my Evo II seat mounted to a Wedge Engineering seat mount and had to ditch the rails. I bought the Z1 side mounts for the passenger side and will be fix mounting the passenger seat. I don't like sliders for a track car unless OEM. Just my two cents. I do like the simplicity of Z1 mounts. My driver's is a custom mount but if I don't like it I may go with the Z1 side mount. Sent from my SM-G965U using Tapatalk Corsairprime likes this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

02-01-2022, 06:59 AM	#8 (permalink)
mara Base Member Join Date: Jan 2020 Location: NSW Posts: 2 Drives: my16 370z Rep Power: 5	Do you mind telling us how tall you are and what sort of head clearance you are getting with a helmet on. Also does your sparco seating position sit lower then oem seat. Reason im asking as im 6"2 and looking at getting a set or seats so i can fit in the car with a helmet on. (Tall ppl problems) Corsairprime likes this. Last edited by mara; 02-01-2022 at 07:06 AM.

02-03-2022, 10:58 AM	#15 (permalink)
Corsairprime Base Member Join Date: May 2014 Location: Frisco, TX Posts: 215 Drives: 14 370Z Nismo GM 6MT Rep Power: 3545	Ok, I did the same fingers above the Helmet test on the passenger seat. The clearance measurement for me is the same as the drivers seat. I get 2 fingers above the crown of the helmet. Two fingers translates to 1.5" at a maximum to the headliner in my Z. You definitely sit lower in the car. It is interesting to note without the helmet, I'd say there is about 3.5" to 4" from the top of my head to the headliner. It feels very roomy for a car with racing seats and 5 point harnesses. __________________ Corsairprime 2014 Nismo #462, GunMetal Grey, GT-R Start Button, AAM S-Line/R-Line intake and S-Line exhaust, Berk HFCs, Osiris Tuned at JoTech

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Sparco Evo L Seat W/Rails - $300	MyLadyZ	Parts for sale (Private Classifieds)	3	03-15-2018 06:40 PM
[FOR SALE] Bride seat rails	JENZ	Parts for sale (Private Classifieds)	23	03-27-2017 07:43 PM
[FOR SALE] Bride RO Seat Rails	CarbonFZ	Parts for sale (Private Classifieds)	24	07-30-2015 04:09 PM
Seat rails that will seat around stock height or slightly lower?	Volk Z	Exterior & Interior	15	05-08-2013 02:12 PM
Seat rails?	AWX Z34	Nissan 370Z General Discussions	0	03-05-2012 02:02 PM