ECUTEK/UPREV idle relearn

THE BULL · 07-27-2022, 03:00 PM

Hello everyone, is it possible to force an idle relearn on swaps?

Playing around with Ecutek on my swap I tried doing an idle relearn however it was unsuccessful. I idle around 750-800rpm/ 18% load after warm up(no codes) which is fine however it peeked my curiosity since Ecutek has the ability however some swaps wouldn't have IPDM, hood switch and other requirements "needed" for the relearn.

So far disconnecting/connecting throttles dont act like a Z/G where on some occasions requires the relearn, mine's coldstarts and goes through the warm up process just like OEM however stays at 750-800rpm instead of the 650-700rpm that usually see which doesnt bother me however makes me question if this is due to the lack of the learn which at the moment seems unobtainable.

Thanks in advance.

abm89 · 07-27-2022, 03:05 PM

I dont know about swaps, but you can run the ECUtek relearn from the phone. I have never got it to work properly, but my car will auto learn after an ECM reset.

idk if that's any help.

THE BULL · 07-27-2022, 03:27 PM

Quote:

Originally Posted by abm89

I dont know about swaps, but you can run the ECUtek relearn from the phone. I have never got it to work properly, but my car will auto learn after an ECM reset.

idk if that's any help.

Same here, it will "auto relearn" to a point however from the phone it will not work.

abm89 · 07-27-2022, 03:28 PM

750 to 800 is ok tbh. it depends on your setup though.

THE BULL · 07-27-2022, 03:37 PM

Quote:

Originally Posted by abm89

750 to 800 is ok tbh. it depends on your setup though.

I'm happy with it however I own a G37 and wonder if the remaining 100rpm is would be achieved by the relearn or other possible aspects.

I prefer the higher RPM but wonder about other's results.

07-27-2022, 03:00 PM	#1 (permalink)
THE BULL Base Member Join Date: Apr 2021 Location: Florida Posts: 217 Drives: G37S Rep Power: 26848	ECUTEK/UPREV idle relearn Hello everyone, is it possible to force an idle relearn on swaps? Playing around with Ecutek on my swap I tried doing an idle relearn however it was unsuccessful. I idle around 750-800rpm/ 18% load after warm up(no codes) which is fine however it peeked my curiosity since Ecutek has the ability however some swaps wouldn't have IPDM, hood switch and other requirements "needed" for the relearn. So far disconnecting/connecting throttles dont act like a Z/G where on some occasions requires the relearn, mine's coldstarts and goes through the warm up process just like OEM however stays at 750-800rpm instead of the 650-700rpm that usually see which doesnt bother me however makes me question if this is due to the lack of the learn which at the moment seems unobtainable. Thanks in advance.

07-27-2022, 03:05 PM	#2 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	I dont know about swaps, but you can run the ECUtek relearn from the phone. I have never got it to work properly, but my car will auto learn after an ECM reset. idk if that's any help. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

07-27-2022, 03:28 PM	#4 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	750 to 800 is ok tbh. it depends on your setup though. Optimiser likes this. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Help with Idle Air Volume Relearn Procedure	T-Rex57	Intake/Exhaust	14	10-07-2019 01:01 PM
Ecutek: Weird fuel trim issues and miss at idle	Rob298mx	Tuning	0	09-02-2016 05:38 PM
Throttle body idle relearn	avery370z	Engine & Drivetrain	3	06-02-2016 12:35 PM
UpRev to EcuTek - Here we go...	mezzo	Tuning	20	10-31-2015 10:28 AM
uprev vs ecutek ?	bleunetizen	Tuning	4	08-29-2014 09:14 AM