ZSpeed CMAK with a RJM clutch pedal??

dvboy · 04-21-2021, 09:03 AM

Couldn't find this on a search,but do these 2 components work well together?Currently have my RJM pedal installed,the APF setting is at 50%,is that a good place to start and can the CMAK be bled at that setting,or would I have to slide it to the stock setting (0%) to do that like the stock CSC?Do not have the CMAK as of yet.

40 to 332 · 04-21-2021, 10:11 AM

They work well together. Ask Ryan at RJM about the best settings for bleeding. He's always very helpful and is familiar with the CMAK unit.

stock12 · 04-23-2021, 09:23 PM

From the Rev 3.x instruction manual on RJM's website:

Quote:

* Note On Bleeding Clutch System* If you are attempting to manually bleed the hydraulic system (without a Power Bleeding System) while the RJM Pedal is installed then you must reduce the AFP setting to 0% restoring full stroke to the master cylinder in order toget all the air out. Failing to do so will make manual bleeding extremely difficult of not impossible. You must also adjust the Clutch Rod angle to ensure the master cylinder rod is moving straight in/out of the master cylinder after adjusting the AFP setting to Zero. Failure to adjust the clutch rod angle may cause binding of the pedal linkage and potentially damage to the master cylinder internally. Please see the Tuning Section of this RJM Installation Guide for Specific Steps Required.

dvboy · 04-23-2021, 10:13 PM

Quote:

Originally Posted by stock12

From the Rev 3.x instruction manual on RJM's website:

Thanks.....I believe these instructions were intended for the stock clutch/csc set-up,but I did contact Ryan at RJM and the same applies for the CMAK set-up as well(setting APF at 0% for bleeding).Joe at ZSpeed recommends leaving the RJM pedal in the stock APF (0%)position after the bleeding is complete.Ryan at RJM says u can adjust it to the 50-75% APF setting with the ZSpeed clutch/CMAK after the bleeding is complete.I am going to try it out at the stock 0% first and maybe bump it up to 25-50% if I want to change the feel a bit.

stock12 · 04-23-2021, 10:22 PM

It sounds like it's safest at 0% (or just using a power bleeder if you have one) but you can keep it at 50-75% if you have a CMAK. If that's the way you like it, it's more convenient to leave it at that setting while you bleed, but if you have to adjust it anyway, you might as well adjust it to 0 to be safest.

Is that the gist of it?

dvboy · 04-23-2021, 10:49 PM

With the CMAK the APF setting has to be set to 0% to do a proper bleed just like the stock system.

04-21-2021, 09:03 AM	#1 (permalink)
dvboy Enthusiast Member Join Date: Jun 2015 Location: Canada Posts: 269 Drives: 2016,M6 Rep Power: 26	ZSpeed CMAK with a RJM clutch pedal?? Couldn't find this on a search,but do these 2 components work well together?Currently have my RJM pedal installed,the APF setting is at 50%,is that a good place to start and can the CMAK be bled at that setting,or would I have to slide it to the stock setting (0%) to do that like the stock CSC?Do not have the CMAK as of yet. __________________ Pioneer AVIC 8000NEX,Hertz ML 1600,ScanSpeak D3004,Audison AV 5.1K,Helix DSP.2,Illusion Audio L10 Sub,RJM Clutch pedal,Stillen G3 long tube intake,Nismo exhaust,AAM S-line axle back,Ecutek tune Last edited by dvboy; 04-24-2021 at 10:42 AM.

04-23-2021, 10:49 PM	#6 (permalink)
dvboy Enthusiast Member Join Date: Jun 2015 Location: Canada Posts: 269 Drives: 2016,M6 Rep Power: 26	With the CMAK the APF setting has to be set to 0% to do a proper bleed just like the stock system. BettyZ likes this. __________________ Pioneer AVIC 8000NEX,Hertz ML 1600,ScanSpeak D3004,Audison AV 5.1K,Helix DSP.2,Illusion Audio L10 Sub,RJM Clutch pedal,Stillen G3 long tube intake,Nismo exhaust,AAM S-line axle back,Ecutek tune

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ZSpeed Stage 1, 2 & 3 Clutch and CMAK Clutch Release System Packs! In Stock!	Joe@ZSpeed	Drivetrain/Engine	85	12-17-2024 04:52 PM
ZSpeed Performance CMAK "V2" CSC Delete CLUTCH MOVEMENT ALTERATION KITS Now Available	Joe@ZSpeed	Drivetrain/Engine	34	04-21-2020 08:57 AM
[WTB] ZSPEED Clutch/Flywheel + CMAK combo	dboss	Parts for sale (Private Classifieds)	1	03-26-2019 10:53 AM
ZSpeed CMAK Clutch Movement Alteration Kit CSC Delete	Joe@ZSpeed	Drivetrain/Engine	114	07-17-2018 10:36 AM
ZSpeed Performance "CMAK" Review	cdoxp800	Engine & Drivetrain	26	01-31-2018 12:45 AM

04-21-2021, 10:11 AM	#2 (permalink)
40 to 332 Enthusiast Member Join Date: Apr 2013 Location: Kimberley, BC, CANADA Posts: 452 Drives: 13 370Z BS M6 Sport Rep Power: 439	They work well together. Ask Ryan at RJM about the best settings for bleeding. He's always very helpful and is familiar with the CMAK unit.

04-23-2021, 10:22 PM	#5 (permalink)
stock12 Base Member Join Date: Jan 2019 Location: Ontario, Canada Posts: 12 Drives: 2012 370Z Touring Rep Power: 77	It sounds like it's safest at 0% (or just using a power bleeder if you have one) but you can keep it at 50-75% if you have a CMAK. If that's the way you like it, it's more convenient to leave it at that setting while you bleed, but if you have to adjust it anyway, you might as well adjust it to 0 to be safest. Is that the gist of it?