|
I obtained and installed the CZP 34 row oil cooler kit and it has done an amazing job of bringing down the oil temps on my 370z, maybe too good.
|
|||||||
 |
|
|
LinkBack | Thread Tools | Display Modes |
06-12-2020, 07:15 PM
|
#1 (permalink) |
|
Base Member
 
Join Date: May 2020
Location: Houston, TX
Posts: 36
Drives: 2010 370z Supercharg
Rep Power: 5  |
Engine oil temps too low with 34 row setrab oil cooler?
I obtained and installed the CZP 34 row oil cooler kit and it has done an amazing job of bringing down the oil temps on my 370z, maybe too good. It used to run on average around 220-230, up to 240 when I have pushed it some. After installing this oil cooler, I have not seen it get past 205-210 degree range and during general driving it has been averaging 185-190. Is this too low? Granted it is Texas and it is only in the 80s right now, but will quickly get to the 100s and then I might be happy about the temps. Thoughts?
|
|
|
|
06-12-2020, 07:36 PM
|
#2 (permalink) |
|
A True Z Fanatic
Join Date: Nov 2009
Location: Western Maryland
Posts: 1,280
Drives: Wife crazy & 09 370Z
Rep Power: 105454  |
185+ is fine. Anything lower then that for extended time is bad. If it goes lower, I would recommend a thermostatic oil sandwhich plate.
__________________
~Rob  -DD Air Guide, Stillen G3 CAIs, 63mm Throttle Bodies, Motordyne M370, Berk HFCs, FI TDX CBE (non-res, CF), Sprint booster v3, Ecutek Dyno Tuned, and the list goes on... |
|
|
|
|
06-13-2020, 04:28 PM
|
#4 (permalink) |
|
A True Z Fanatic
Join Date: Jan 2016
Location: Atlantic SE
Posts: 1,323
Drives: '10 K23 ST 7AT
Rep Power: 30525 |
I have a Setrab 25 row with 6 rows blocked off and a Termo plate and will still barely sniff 180* in FL summer. Probably blocking off 2 more rows. Comparing apples to apples same highway temps as you pre-cooler install and post cooler install.
__________________
Toys Not Tots |
|
|
|
|
06-20-2020, 05:39 PM
|
#5 (permalink) |
|
Enthusiast Member
Join Date: Nov 2009
Location: SF, CA
Posts: 339
Drives: 17 C7 Z06 M7
Rep Power: 66 |
Don't worry about it, especially for part-throttle applications. You just don't want the temperature going past 230 as you start to lose power and past 260+ as it starts to damage the oil. When I still had my Z, I seriously considered adding a 2nd 34-row cooler.
__________________
2017 Corvette Z06 7MT | 1LE | Stage 3 | DSCSport |
|
|
|
|
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| [FOR SALE] Setrab 25 row oil cooler (just the cooler, no lines) - central NJ | PharmDZ | Parts for sale (Private Classifieds) | 4 | 04-06-2019 09:46 AM |
| [WTB] Setrab Oil Cooler | jjonas828 | Parts for sale (Private Classifieds) | 0 | 09-21-2014 10:31 PM |
| [WTB] Setrab 25 or 34 Row Oil Cooler | jjonas828 | Parts for sale (Private Classifieds) | 0 | 08-31-2014 09:58 AM |
| Concern with Oil Cooler / Oil Temps | PharmDZ | Engine & Drivetrain | 18 | 05-05-2014 05:08 PM |
| [FOR SALE] AT Transmission Cooler with Setrab 19 Row cooler | zakimak | Parts for sale (Private Classifieds) | 4 | 03-03-2012 12:44 PM |
2Likes
Linear Mode
