CSC issue continues...

flytime · 07-15-2019, 10:06 AM

Hello everyone. 2011 370z sport tech w/83k on the clock. The CSC was replaced with zspeed HD CSC. Used Motul High temp brake fluid. After the install the car would start squeaking with the clutch out. If you put push in the clutch it squeal. I'm not sure what the issue is but I plan to put the car on Jack's again and drop the transmission. Something is obviously not right....

flytime · 07-15-2019, 11:08 AM

There's pressure on the clutch pedal and the fluid is full. I'm at a lost on why it's squeaking and squealing. Any input would be greatly appreciated. Perhaps it was aligned right? I'm not sure.

BettyZ · 07-16-2019, 09:15 PM

What made you opt for the HD CSC instead of getting a CMAK?

Sent from my SM-G955U using Tapatalk

JARblue · 07-16-2019, 09:16 PM

Who did the install? I'd take it back to them. Was the CMC done also? ZSpeed products are top notch, so I doubt it's the HD CSC. Joe can answer any questions you might have.

-ZS-Carpenter · 07-16-2019, 09:40 PM

did you change the pilot bushing?

2011 Nismo#91 · 07-17-2019, 06:23 AM

Installation issue would be my guess, either something was missed or not adjusted correctly.

07-15-2019, 10:06 AM	#1 (permalink)
flytime Base Member Join Date: Mar 2017 Location: Sheboygan Posts: 11 Drives: 2011 Nissan 370z Rep Power: 8	CSC issue continues... Hello everyone. 2011 370z sport tech w/83k on the clock. The CSC was replaced with zspeed HD CSC. Used Motul High temp brake fluid. After the install the car would start squeaking with the clutch out. If you put push in the clutch it squeal. I'm not sure what the issue is but I plan to put the car on Jack's again and drop the transmission. Something is obviously not right....

07-16-2019, 09:15 PM	#3 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 38 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	What made you opt for the HD CSC instead of getting a CMAK? Sent from my SM-G955U using Tapatalk __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

07-16-2019, 09:16 PM	#4 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	Who did the install? I'd take it back to them. Was the CMC done also? ZSpeed products are top notch, so I doubt it's the HD CSC. Joe can answer any questions you might have. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

07-16-2019, 09:40 PM	#5 (permalink)
-ZS-Carpenter A True Z Fanatic Join Date: Sep 2016 Location: Illinois Posts: 2,410 Drives: 13 370z 6MT Rep Power: 2684367	did you change the pilot bushing? SouthArk370Z likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
10.03 1/4 Mile , the chase continues	Hal@Dynosty	Forced Induction	7	11-08-2017 03:29 PM
Nissan continues to hit new lows!!!!	UNKNOWN_370	Other Vehicles	8	10-26-2017 11:32 AM
Luck continues...	zaimer	Nissan 370Z General Discussions	14	01-15-2016 01:30 PM
Old Z New Z - The legend continues	GiorgioZ	New 370Z Owner	5	02-21-2011 04:39 PM
The pile continues to grow...	Dembflyr	Nissan 370Z General Discussions	3	12-24-2010 11:53 AM

07-15-2019, 11:08 AM	#2 (permalink)
flytime Base Member Join Date: Mar 2017 Location: Sheboygan Posts: 11 Drives: 2011 Nissan 370z Rep Power: 8	There's pressure on the clutch pedal and the fluid is full. I'm at a lost on why it's squeaking and squealing. Any input would be greatly appreciated. Perhaps it was aligned right? I'm not sure.

07-17-2019, 06:23 AM	#6 (permalink)
2011 Nismo#91 A True Z Fanatic Join Date: Mar 2011 Location: NJ Posts: 2,402 Drives: slowly Rep Power: 40569	Installation issue would be my guess, either something was missed or not adjusted correctly.