Bleeding CMC

ARrado15 · 04-17-2016, 01:20 AM

So I replaced my CMC, slave, clutch and flywheel and when I go to gravity bleed it, nothing happens. The fluid stays in the reservoir and goes no where. I've tried pumping the clutch but nothing. Is there anything in doing wrong?

ARrado15 · 04-17-2016, 05:33 AM

I got it working. I had to tighten everything up, then loosen up the hard line going to the master cylinder. I then had my wife slowly press the clutch down, while I simultaneously open the line a little to let the bubbles escape. Then I would crack the slave bleeder and repeat. Once I got a good flow from the slave, I only would bleed the slave.

Spstone · 04-25-2016, 01:43 PM

I have yet to do it on a 370, but I know on the 300ZX and the ranger I had with a similar CSC the only way to do it was with a vacuum bleeder or a pressure bleeder. I think I paid 30 or 40 bucks for my vacuum bleeder and just keeping the amount of clean up down was worth the money.

04-17-2016, 01:20 AM	#1 (permalink)
ARrado15 Base Member Join Date: Nov 2015 Location: Las Vegas Posts: 96 Drives: 370z M6 Rep Power: 17	Bleeding CMC So I replaced my CMC, slave, clutch and flywheel and when I go to gravity bleed it, nothing happens. The fluid stays in the reservoir and goes no where. I've tried pumping the clutch but nothing. Is there anything in doing wrong? __________________ Stillen G3, Stillen CBE, Berk HFC, Eibach Springs, H&R Spacers, PW:JDM Knob, RJM Clutch Assembly, Z1 Clutch & Flywheel, Zspeed HD CSC, Stillen Oil Cooler

04-17-2016, 05:33 AM	#2 (permalink)
ARrado15 Base Member Join Date: Nov 2015 Location: Las Vegas Posts: 96 Drives: 370z M6 Rep Power: 17	I got it working. I had to tighten everything up, then loosen up the hard line going to the master cylinder. I then had my wife slowly press the clutch down, while I simultaneously open the line a little to let the bubbles escape. Then I would crack the slave bleeder and repeat. Once I got a good flow from the slave, I only would bleed the slave. YzGyz likes this. __________________ Stillen G3, Stillen CBE, Berk HFC, Eibach Springs, H&R Spacers, PW:JDM Knob, RJM Clutch Assembly, Z1 Clutch & Flywheel, Zspeed HD CSC, Stillen Oil Cooler

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Calling all clutch bleeding experts	Rangerz	Engine & Drivetrain	9	10-22-2014 11:33 AM
Desperate for clutch bleeding help	Pheonix	Engine & Drivetrain	22	05-10-2014 03:21 AM
Clutch bleeding BIG issues	edconline	Engine & Drivetrain	16	04-10-2014 09:00 AM
Problem with Brake Bleeding	Read T	Brakes & Suspension	3	12-08-2013 05:32 PM
Brake bleeding sequence	fastguy9r	DIY Section (Do-It-Yourself)	3	07-04-2012 10:22 AM

04-25-2016, 01:43 PM	#3 (permalink)
Spstone Enthusiast Member Join Date: Aug 2015 Location: Wilmington, nc Posts: 354 Drives: 14 370Z Nismo 6MT PW Rep Power: 10	I have yet to do it on a 370, but I know on the 300ZX and the ranger I had with a similar CSC the only way to do it was with a vacuum bleeder or a pressure bleeder. I think I paid 30 or 40 bucks for my vacuum bleeder and just keeping the amount of clean up down was worth the money.