Help/Advice with SPC Toe Bolt Install

KeCh · 02-22-2019, 04:45 AM

I was planning to install the SPC toe bolt along with my camber arms this weekend. I am going to be following the DIY post; however, I just have a few questions. I heard that the 2013+ 370z models have a steel sub frame instead of aluminum which makes things complicated. Which dremel bit should I use for the steel subframe since the recommended bits were for the aluminum subframe. Also, how could I protect my elongated holes from rusting. Could I just spray some primer for steel? Thanks.

Senna-F1 · 02-22-2019, 04:58 AM

I believe i used a tungsten carbide cutter. I still broke 1 so don’t use too much pressure.

https://rover.ebay.com/rover/0/0/0?m...2F381148829530

Sent from my iPhone using Tapatalk

Rusty · 02-22-2019, 08:56 PM

All of the 370Z sub-frames are steel.

The burr bit posted will work. Tip, dip the end of the bit in ATF before you start. It will help keep the bit sharp.

To keep the metal from rusting. You can get a spray can of cold galvanizing paint. Spray it into a cup and brush it on.

KeCh · 02-24-2019, 03:03 AM

Thank you guys very much

02-22-2019, 04:45 AM	#1 (permalink)
KeCh Base Member Join Date: Sep 2018 Location: BC, Canada Posts: 5 Drives: 16 Nissan 370z M6 Rep Power: 7	Help/Advice with SPC Toe Bolt Install I was planning to install the SPC toe bolt along with my camber arms this weekend. I am going to be following the DIY post; however, I just have a few questions. I heard that the 2013+ 370z models have a steel sub frame instead of aluminum which makes things complicated. Which dremel bit should I use for the steel subframe since the recommended bits were for the aluminum subframe. Also, how could I protect my elongated holes from rusting. Could I just spray some primer for steel? Thanks.

02-22-2019, 04:58 AM	#2 (permalink)
Senna-F1 Enthusiast Member Join Date: Jun 2016 Location: Cary, NC Age: 54 Posts: 425 Drives: 370SC,EliseSC,MR2T Rep Power: 50	I believe i used a tungsten carbide cutter. I still broke 1 so don’t use too much pressure. https://rover.ebay.com/rover/0/0/0?m...2F381148829530 Sent from my iPhone using Tapatalk KeCh likes this. __________________ 618 WHP.452 WTQ.4" Python Intake.15 psi.e50.Topgunz SC.SOHO Tune.S1SE.STG 4 Clutch.Motordyne LTH/Test Pipes/Exhaust.485 Pump.1050x

02-22-2019, 08:56 PM	#3 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,218 Drives: 2011 Nismo GM 6M Rep Power: 2684438	All of the 370Z sub-frames are steel. The burr bit posted will work. Tip, dip the end of the bit in ATF before you start. It will help keep the bit sharp. To keep the metal from rusting. You can get a spray can of cold galvanizing paint. Spray it into a cup and brush it on. KeCh likes this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
H&r spacers bolt on install	Zero dark	Wheels & Tires	0	03-27-2015 12:49 AM
alignment/camber adjustment/toe bolt install	David Parra	Southern California Region	7	07-28-2013 04:46 PM
Toe bolt install question	olddudesrule	Brakes & Suspension	8	06-07-2013 05:29 PM
Any advice on getting rusted bolt off the exhaust?	ssmoked	Intake/Exhaust	9	05-16-2013 04:43 PM
Diy spc toe bolt install (MISTAKE) HELP	RedBullRR	DIY Section (Do-It-Yourself)	2	08-19-2011 03:25 PM

02-24-2019, 03:03 AM	#4 (permalink)
KeCh Base Member Join Date: Sep 2018 Location: BC, Canada Posts: 5 Drives: 16 Nissan 370z M6 Rep Power: 7	Thank you guys very much