8" Mid-bass in doors...

ChopsZ

I have yet to pull the door cards off of my Z, and have only seen a few pictures of the speaker opening in the door itself.

How much space is there between the door and the rear of the door card? If a thick enough baffle is used, do you guys think an 8" mid-bass driver would fit without interfering with the fitment of the door card?

Many thanks in advance!

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

night blade

I'd just take the door panel off and measure it, not that hard to to do. Installed 6.75" a month or so ago, it was a tight fit for sure, but you never know, these mid's are huge, can't imagine a 8" fitting there.

__________________
2016 Nissan 370z Base 6MT Pearl White | RJM Performance
2012 Kia Sportage 6AT (the short bus)

MaysEffect

no.

ChopsZ

Yeah, I'm not too terribly concerned with it. It's more of a curious thing than anything. I'll be replacing the dash tweeters and dynamatting the rear of the car way before I do anything with door speakers.

The stock door speakers don't sound half bad with a good head unit with decent power going to them, and high-pass them around 40 - 50 Hz. Even better when you low-pass them anywhere below 4 kHz.

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

ChopsZ

Yeah, great explanation there...

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

RonRizz

Main concern would be depth. Yes, you can fit an 8" in the door, with minor modification, and plenty of deadening. If I remember correctly, the factory baffle is about 1" thick.
The Bose setup comes with 6x9's in doors, if i'm not mistaken, so an 8" is definitely do-able.

__________________
P99rs Head Unit--- Amps- 2 Pioneer Prs800d --- Zapco ST1000MX---Zapco ST-4XSQ---- SI BM mk5 Subs---SI TM65v2 Midbass--- SI M3 mids--- SI M25 xbl2 tweeters ----- 2016 MECA street class 3rd place at world finals

ChopsZ

Pretty much what I was thinking. As you said, the Bose system comes with 6x9's, so an 8" driver shouldn't be too difficult you would think.

Mounting depth shouldn't be an issue, at least from some of the 8" drivers that I've been looking at. They're about the same (a couple even less) than some 6.5" drivers.

The real concern would be clearance between the driver and door card as well as making a spacer that can possibly move the driver off center from the stock opening in the door to allow it to fit properly.

BTW, I'm not looking at component sets, but rather raw drivers. Controlling it all actively via the head unit gives me a lot more selection and flexibility on what drivers to choose from.

Right now, I'm just researching my options.

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

Jayhovah

I'd think it could be done, but the magnet will need to clear the hole in the sheet metal, and the excursion can't be so crazy that the portions of the cone not over the hole don't bottom out on you. If you were willing to cut metal, I'd bet this could be done pretty easily.

__________________
2013 Gun Metallic Sport - Gamma V3 Twin Turbogized
DIY Gamma V3 TT Install * Jayhovah's Gamma V3 TT Install Pic'Z and Vid'Z * DIY: Washer Reservoir for the Boosted