Lug Nuts - The definitive guide

chops · 12-16-2013, 11:36 PM

Quote:

Originally Posted by kenchan

should have my neo's by end of the week.

just got my locks on! no pic, but heres the 4 i took off to put locks on. you'll like the color on the sa-55's!

equalme · 12-16-2013, 11:40 PM

I had no intention of replacing my lug nuts...but since I just lost the key to the mcgard locks I might as well spend the money on the muteki!

The SR48 won't stick out too funky on the stock rays would they?

chops · 12-17-2013, 12:32 AM

Quote:

Originally Posted by equalme

I had no intention of replacing my lug nuts...but since I just lost the key to the mcgard locks I might as well spend the money on the muteki!

The SR48 won't stick out too funky on the stock rays would they?

do not use tuner lugs on stock wheels!!! you will break the studs

equalme · 12-17-2013, 08:36 AM

Quote:

Originally Posted by chops

do not use tuner lugs on stock wheels!!! you will break the studs

How so? I thought lugs were lugs...

osbornsm · 12-17-2013, 08:42 AM

Quote:

Originally Posted by equalme

How so? I thought lugs were lugs...

Please re-read initial post of this thread.

...Then come back and edit your post.

wstar · 12-17-2013, 08:44 AM

Quote:

Originally Posted by kenchan

you shouldn't use impact wrenches with those adapters... hell, i dont use impact wrenches on any of my nice wheels.

Eh they're track wheels, I don't care about scratches, they come off a lot, and there's no real harm using an impact to remove (just not to install!). Except for the part about the weak thin-walled adapters. They don't always break, so I've learned to just stock up on them (don't throw away old ones when I get new ones) since they're all the same pattern anyways.

equalme · 12-17-2013, 09:13 AM

So looks like I will need washer type lugs which the muteki are not?

wstar · 12-17-2013, 09:25 AM

Yes, the stock wheels need the washer-style, the Muteki's are cones.

kenchan · 12-17-2013, 10:30 AM

Quote:

Originally Posted by wstar

Eh they're track wheels, I don't care about scratches, they come off a lot, and there's no real harm using an impact to remove (just not to install!). Except for the part about the weak thin-walled adapters. They don't always break, so I've learned to just stock up on them (don't throw away old ones when I get new ones) since they're all the same pattern anyways.

the adapters are not meant to be used with an impact, that's wat i meant.

scratches on lug bores is more of a personal issue i have with wheels. i hate scuffed up wheels.

thus i never take my wheels to the tire shop while still on the car (unless it's at tirerack... they use hand jacks and hand tools and low power drivers).

Apoc370z · 12-17-2013, 12:56 PM

Quote:

Originally Posted by kenchan

should have my neo's by end of the week.

can i call you daddy and you buy me a set for christmas as well?

GaleForce · 12-18-2013, 10:05 AM

So where are we at in regards to Aluminium nuts? These are 7075 T6 aluminum, which is very strong from what I understand (I'm not a metallurgist though). If torqued properly = ok? Add anti-seize to be safe = good to go?

fuct · 12-18-2013, 11:09 AM

Quote:

Originally Posted by equalme

So looks like I will need washer type lugs which the muteki are not?

ding ding ding, we have a winner!

kenchan · 12-18-2013, 01:10 PM

mr.gale- im sure they do fine as long as you use the entire thread allowed and 80lbs/ft.

minimum thread needed is 10mm for steel lugs, so perhaps you might need 13-14mm just to be on the safe side. i too have no scientific data on the strengths.

however i do know they strip a lot easier than steel lugs.

Waiz · 12-18-2013, 02:03 PM

Quote:

Originally Posted by GaleForce

So where are we at in regards to Aluminium nuts? These are 7075 T6 aluminum, which is very strong from what I understand (I'm not a metallurgist though). If torqued properly = ok? Add anti-seize to be safe = good to go?

If you plan on removing your wheels alot I would pass, otherwise they are fine to use

Under no circumstance should you use anti-seeze on your lugs or studs though

fuct · 12-19-2013, 07:47 AM

12-17-2013, 09:13 AM	#67 (permalink)
equalme Track Member Join Date: Feb 2013 Location: Kansas City Posts: 656 Drives: RCF Rep Power: 14	So looks like I will need washer type lugs which the muteki are not? osbornsm likes this.

12-17-2013, 09:25 AM	#68 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3595	Yes, the stock wheels need the washer-style, the Muteki's are cones. __________________ 7AT Track Car! Journal thread / Car setup details

12-18-2013, 10:05 AM	#71 (permalink)
GaleForce A True Z Fanatic Join Date: Aug 2011 Location: Ontario, Canada Posts: 21,749 Drives: Varis Arising II Rep Power: 51865	So where are we at in regards to Aluminium nuts? These are 7075 T6 aluminum, which is very strong from what I understand (I'm not a metallurgist though). If torqued properly = ok? Add anti-seize to be safe = good to go? __________________ >>>GaleForce's Build<<< >>>FaceBook @3GsCustoms<<<>>>Instagram @GaleForce370z<<< Varis Kamikaze-Z

12-18-2013, 01:10 PM	#73 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	mr.gale- im sure they do fine as long as you use the entire thread allowed and 80lbs/ft. minimum thread needed is 10mm for steel lugs, so perhaps you might need 13-14mm just to be on the safe side. i too have no scientific data on the strengths. however i do know they strip a lot easier than steel lugs. GaleForce likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
EcoJet: Definitive Edition - Jay Leno's Garage	Nismo89	Other Vehicles	0	10-31-2012 10:32 PM
The Definitive Z34 Brake Resource	SE	Brakes & Suspension	68	05-11-2012 02:19 PM
A guide for your next office encounter	Anatoray	The Lounge (Off Topic)	0	03-15-2011 04:35 PM
Nissan Chemical Guide PDF	kdo2milger	Nissan 370Z Owners Manual / Service Manuals	8	07-20-2009 02:04 PM

12-16-2013, 11:40 PM	#62 (permalink)
equalme Track Member Join Date: Feb 2013 Location: Kansas City Posts: 656 Drives: RCF Rep Power: 14	I had no intention of replacing my lug nuts...but since I just lost the key to the mcgard locks I might as well spend the money on the muteki! The SR48 won't stick out too funky on the stock rays would they?

12-19-2013, 07:47 AM	#75 (permalink)
fuct A True Z Fanatic Join Date: May 2009 Location: Sugar Land Posts: 3,692 Drives: 97' Ranger :) Rep Power: 24