Wheel Locks for '10 Nismo
 

Will these locks fit the car?

http://www.rhdjapan.com/kyo-ei-dency...t-silver-30851

Wanted to make sure since I have been reading up on all the problems people had with the wrong wheel locks from Nissan.


I am guessing the "Part Num: DY03C (M12xP1.25)" is the correct part!?!?!

Thanks for the help

More than likely....sorry to say...nope.

The OEM rims need a "mag" style or a washer type lug nut. These would work if you have aftermarket rims.

You would probably have to use the OEM wheel locks...it looks like this:

http://www.the370z.com/north-west-re...eel-locks.html

Sorry to say.

I used the make and model selector on the site and they were listed for a 370Z... weird oh well.

i watched the guy at discount tire remove all four factory locks in under 20 minutes. (i lost my key)

These are a bit different though they are covered by a cap that is held on by a pretty strong magnet. The cap has to be removed to get to the "Key" part and the cap rotates around the lug/key. Read some pretty good review on the product but you are right given the right tools and time I am sure anyone can get them off.

Anyways after doing a bit more research the lug is not the type on the 370Z Nismo even though the site claims they should work. I was hoping I was wrong but guess not :-)

Hey Fuct,

Did you put wheel locks on your NISMO and if so can you advise of the make and model so I can order some? Thanks in advance.

Only wheel locks i know of for any of the factory wheels are the OEM locks, which in my opinion are a POS.

yah talk to your dealer for the factory locks.

Actually I ordered "Gorilla" brand wheel lock part #63621. Found them on Amazon.com for around $13. Better than $51 form the dealer.

For stock wheels I would go with stock wheel locks. The stock lugs have a washer on them. The stealership put the wrong wheel locks on my z and now one is stripped while the other lock just snapped off, so be careful

Check out the sticky: http://www.the370z.com/wheels-tires/...d-lug-nut.html

http://ecx.images-amazon.com/images/...500_AA300_.jpg

yea these wont work, sorry man.

Which Oem locks fit the Sport Rays? Anywhere I can get them cheap?

Why not? Please state reason.:tiphat:

wat's the diameter of the flat section? it appears too narrow :confused:

it came with four washers for that reason.:happydance:

^^ nice. take some snaps.

Will do, but I am at work and will be here till 9pm tonight. I will have to take them in the morning. Fingers crossed.

:driving:

wheres the washer? you said it came with them, how are the washers mounted on this type of lug?

Here are some pre-install pics...

Two more coming.

Last two...

The washers they packaged were a little to short, so I had to go to Autozone and pickup another set of them and made sure that they were also a little wider. Plus I had to stack them together. Here is a comparison photo and then a finished photo. All in all, the grad total was $20 bucks. WINNING!

Do you guys think that the KYO-EI DENCY 2000 LOCK NUTS
Wold work for a OEM sport package rim? DYO3C
KYO-EI - Dency 2000 Lock Nuts - Nengun Performance
It's either this OR Parking enforcement tire parking boot, booting enforcement
Or
http://www.amazon.com/Gorilla-Automo...ar=1&carId=001

hahaha buy the boot!

I just placed an order of these Lug Nuts + Lock Nuts for my black powdercoated Nismo Wheels.
12x1.25 Black Lug Nuts: Standard Mag .750 Inch Shank Lug Nuts-Set of 20-Flat Seat-CW5205B
Gorilla 73621NBC $19.7 Wheel Locks - Set of 4 Standard Mag Seat, Black 13/16" Hex Key Included 12mm x 1.25 Thread

These should work right?

So...did it work???

It worked out just fine. I had to use two washers per lug nuts. No issues thus far.