DEALER says Ichiba 20mm Type 2 Bolt-On Wheel Spacers are DANGEROUS!?

hansoac · 05-11-2011, 07:29 AM

***MY FAULT: EXACT SPACER ON WHEEL IS Ichiba 20mm Type 2 Bolt-On Wheel Spacers***
So, I have another post about my car stumbling when it sits for awhile and you go to start it. As suggested, I took it to the dealer ASAP. I dropped it off yesterday at 11:00 AM and told the service manager about the issue and also asked him to check out my camber and alignment, as I detected un-even wear on my tires. Well, the guy calls me yesterday at about 4:30 and says they can't find anything wrong with the engine to cause the stumbling and didn't think it was a severe issue. However, the Level 4 Nissan tech that road force balanced my rims was very concerned about the spacers that were installed. He mentioned that the spacers were starting to dig into the rim and that this type of spacer is VERY dangerous to have on and will cause the wheel to fail eventually. He noted that the spacer had begun to dig into the rim and its forcing the axle and tires to not "flex" properly. he also noted that this is why the wheel got a bit shaky at highway speeds. Any thoughts on this...anyone else have these spacers?? I just don't want to take them off if he is being dramatic/jealous because they make the stance look so much more aggressive on the car.

leighspped · 05-11-2011, 08:02 AM

It sounds like u should just take a tire off and take a look for yourself. ....
They are also covering there a$$. They could be right, they can only void the warenty if they prove ur aftermarket product did the damage.... So take a wheel off and post a pic and will see

wstar · 05-11-2011, 08:24 AM

He could have a point if the spacers you're using actually don't match the wheel you're using. Make them show it to you, or check it yourself. You need to visually see this supposed damage to the wheel, and visually/mechanically verify that the spacer is of the correct shape to mate with the wheel and hub correctly. It's always possible you have the wrong model of spacer, or that something else minor is wrong (e.g. there needs to be a hub-centric ring on the inside or outside of the spacer and its missing?).

kenchan · 05-11-2011, 08:24 AM

Need to see picts of the inner side of wheel.

WhiskeyHotel · 05-11-2011, 08:26 AM

Ditto - look for yourself.

PapoZalsa · 05-11-2011, 08:27 AM

Those looks like they are V2, doesn't specify if they are hub centric or not that I can see...

I had Ichiba V2 on my 350Z and didn't have an issue, not heard before about CZP.

hansoac · 05-11-2011, 08:30 AM

These are the EXACT ones i ordered, they are Ichiba's: Ichiba 20mm Type 2 Bolt-On Wheel Spacers - 370Z - performance parts

The guy did mention that the Z uses a hub-centric system..so it needs a hub centric spacer. I am not positive on what exactly this means. My guess is you can't/shouldn't use a bolt on spacer

PapoZalsa · 05-11-2011, 08:47 AM

Quote:

Originally Posted by hansoac

These are the EXACT ones i ordered, they are Ichiba's: Ichiba 20mm Type 2 Bolt-On Wheel Spacers - 370Z - performance parts

The guy did mention that the Z uses a hub-centric system..so it needs a hub centric spacer. I am not positive on what exactly this means. My guess is you can't/shouldn't use a bolt on spacer

You mention CZP first, however hub centric is a ring that comes with the spacer set it keeps the wheels center on the spacer. That way you don't get vibration from your wheels.

Someone correct me if I'm wrong...

hansoac · 05-11-2011, 09:01 AM

Quote:

Originally Posted by PapoZalsa

You mention CZP first, however hub centric is a ring that the spacer set will come with to keep the wheels center on the spacer. That way you don't get vibration of your wheels.

Someone correct me if I'm wrong...

My fault...I got myself mixed up as i ordered them from czp.us

AK..maybe you could update the thread title? Unless there is a way i can do it myself.

wstar · 05-11-2011, 11:17 AM

A wheel or spacer can be hub-centric without using a hub-centric ring (plastic shim). The shims are just so that wheel/spacer mfgs can make universal parts that fit different hub diameters without specializing too much. I don't know whether those specific spacers were meant to be used with a hub-centric ring on our application or not. Ask the mfg?

SPOHN · 05-11-2011, 12:21 PM

Are you on stock wheels?

kenchan · 05-11-2011, 12:28 PM

Quote:

Originally Posted by hansoac

These are the EXACT ones i ordered, they are Ichiba's: Ichiba 20mm Type 2 Bolt-On Wheel Spacers - 370Z - performance parts

The guy did mention that the Z uses a hub-centric system..so it needs a hub centric spacer. I am not positive on what exactly this means. My guess is you can't/shouldn't use a bolt on spacer

you're using the right ones. hubcentric wheels rely on both the hub and lugs to keep it in place.

you need to show us a pict of the inside of the wheel, expecially the center bore (behind the center cap). that's where the hubcentric ring lip sits on. im thinking the dealer is saying he's found some cracks or something in that area.

hansoac · 05-11-2011, 12:41 PM

Quote:

Originally Posted by SPOHN

Are you on stock wheels?

Yeah I am sitting on the 19' rays that come with the sport package.

Kenchan - hopefully can get some pics this weekend. Need to make a trip before ripping the wheels off as I do not have the tools for it laying around.

370Ztune · 05-11-2011, 01:09 PM

The Ichiba spacers are usually hubcentric. The little "lip" around the center of the spacer is the hubcentric ring; it's not a separate piece like Project Kics spacers. The hubcentric ring is there to center the wheel on the hub; when you don't use hubcentric rings, the lugs are used to center the wheel which can cause vibrations at speed.

Check to make sure that the hubcentric ring is still intact and also that it fits your wheel's center bore properly. If there's any kind of play, this is probably where the vibration is coming from.

BeachZTT · 05-11-2011, 02:32 PM

^^ Exactly, I have hubcentric spacers for my Z32 track wheels. You do not want the bolt circle and tapered lugs centering the wheel on the axis of rotation. Something as small as a bent stud can/will cause an eccentric rotation of the entire wheel. Certain cause of vibration no matter how well it is balanced. Usually these situations are minimal at the time of balance and get worse with tire wear.

05-11-2011, 07:29 AM	#1 (permalink)
hansoac Enthusiast Member Join Date: Feb 2011 Location: Toledo Posts: 497 Drives: 09 370z Sport CY Rep Power: 14	DEALER says Ichiba 20mm Type 2 Bolt-On Wheel Spacers are DANGEROUS!? *MY FAULT: EXACT SPACER ON WHEEL IS Ichiba 20mm Type 2 Bolt-On Wheel Spacers* So, I have another post about my car stumbling when it sits for awhile and you go to start it. As suggested, I took it to the dealer ASAP. I dropped it off yesterday at 11:00 AM and told the service manager about the issue and also asked him to check out my camber and alignment, as I detected un-even wear on my tires. Well, the guy calls me yesterday at about 4:30 and says they can't find anything wrong with the engine to cause the stumbling and didn't think it was a severe issue. However, the Level 4 Nissan tech that road force balanced my rims was very concerned about the spacers that were installed. He mentioned that the spacers were starting to dig into the rim and that this type of spacer is VERY dangerous to have on and will cause the wheel to fail eventually. He noted that the spacer had begun to dig into the rim and its forcing the axle and tires to not "flex" properly. he also noted that this is why the wheel got a bit shaky at highway speeds. Any thoughts on this...anyone else have these spacers?? I just don't want to take them off if he is being dramatic/jealous because they make the stance look so much more aggressive on the car. Last edited by hansoac; 05-11-2011 at 09:00 AM.

05-11-2011, 08:02 AM	#2 (permalink)
leighspped Enthusiast Member Join Date: Feb 2011 Location: Morristown Posts: 444 Drives: US Rep Power: 14	It sounds like u should just take a tire off and take a look for yourself. .... They are also covering there a$$. They could be right, they can only void the warenty if they prove ur aftermarket product did the damage.... So take a wheel off and post a pic and will see __________________ Performance: Fast Intentions LTH + CBX + Injen CAI + UpRev + KW3 + Whiteline sway bars + short throw shifter + 34r oil cooler = 335whp + (OS Giken Clutch and Diff) Interior : Recaro seat + Alpine HU and Rockford Fosgate Amp and Speakers + Passport 9500ci + JDM shift knob + LED's Forged avant garde m310's 19x9 19x12 RE-11 Last edited by leighspped; 05-11-2011 at 09:32 AM.

05-11-2011, 08:24 AM	#3 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3594	He could have a point if the spacers you're using actually don't match the wheel you're using. Make them show it to you, or check it yourself. You need to visually see this supposed damage to the wheel, and visually/mechanically verify that the spacer is of the correct shape to mate with the wheel and hub correctly. It's always possible you have the wrong model of spacer, or that something else minor is wrong (e.g. there needs to be a hub-centric ring on the inside or outside of the spacer and its missing?). __________________ 7AT Track Car! Journal thread / Car setup details

05-11-2011, 08:27 AM	#6 (permalink)
PapoZalsa A True Z Fanatic Join Date: Nov 2009 Location: Not in Sunny Florida Posts: 6,358 Drives: 16 Nismo w/Tech Pack Rep Power: 4500	Those looks like they are V2, doesn't specify if they are hub centric or not that I can see... I had Ichiba V2 on my 350Z and didn't have an issue, not heard before about CZP. __________________ 2009 370Z MB Base w/Sport Package 6MT Modshack's Custom Air Intakes /3M Clear Bra/ Illuminated Kick Plates / F. I CBE w/12" resonators / EVO-R Front Lip / Rear Hatch Wing / Tein S-Tech Springs /Ilegal Tint in the Rep. of VA/4x20mm Z1 Spacers/ Vinyl Roof/Liquid Carbon Designs

05-11-2011, 11:17 AM	#10 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3594	A wheel or spacer can be hub-centric without using a hub-centric ring (plastic shim). The shims are just so that wheel/spacer mfgs can make universal parts that fit different hub diameters without specializing too much. I don't know whether those specific spacers were meant to be used with a hub-centric ring on our application or not. Ask the mfg? __________________ 7AT Track Car! Journal thread / Car setup details

05-11-2011, 08:24 AM	#4 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	Need to see picts of the inner side of wheel.

05-11-2011, 08:26 AM	#5 (permalink)
WhiskeyHotel Track Member Join Date: Nov 2009 Location: Oklahoma Posts: 530 Drives: 2015 GT-R PW Premium Rep Power: 17	Ditto - look for yourself.

05-11-2011, 08:30 AM	#7 (permalink)
hansoac Enthusiast Member Join Date: Feb 2011 Location: Toledo Posts: 497 Drives: 09 370z Sport CY Rep Power: 14	These are the EXACT ones i ordered, they are Ichiba's: Ichiba 20mm Type 2 Bolt-On Wheel Spacers - 370Z - performance parts The guy did mention that the Z uses a hub-centric system..so it needs a hub centric spacer. I am not positive on what exactly this means. My guess is you can't/shouldn't use a bolt on spacer

05-11-2011, 12:21 PM	#11 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	Are you on stock wheels? __________________

05-11-2011, 01:09 PM	#14 (permalink)
370Ztune The370Z.com Sponsor Join Date: Jan 2009 Location: Los Angeles, CA Posts: 2,477 Drives: Z34 370Z Rep Power: 46	The Ichiba spacers are usually hubcentric. The little "lip" around the center of the spacer is the hubcentric ring; it's not a separate piece like Project Kics spacers. The hubcentric ring is there to center the wheel on the hub; when you don't use hubcentric rings, the lugs are used to center the wheel which can cause vibrations at speed. Check to make sure that the hubcentric ring is still intact and also that it fits your wheel's center bore properly. If there's any kind of play, this is probably where the vibration is coming from. __________________ The Real JDM Facebook Bulletproof Instagram

05-11-2011, 02:32 PM	#15 (permalink)
BeachZTT Track Member Join Date: Jul 2009 Location: Colorado Posts: 746 Drives: '10 BC ZR T/S/Nav Rep Power: 17	^^ Exactly, I have hubcentric spacers for my Z32 track wheels. You do not want the bolt circle and tapered lugs centering the wheel on the axis of rotation. Something as small as a bent stud can/will cause an eccentric rotation of the entire wheel. Certain cause of vibration no matter how well it is balanced. Usually these situations are minimal at the time of balance and get worse with tire wear. __________________ '10 ZR Black Cherry Sport/Touring/Nav, Swift Springs, Stillen G3s, 15mm-F 20mm-R Spacers, SPC, Spoiler Solutions Rear Wing, Stubby Antenna

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[For Sale] Ichiba Wheel Spacers v2 20mm	mcanlay370Z	Northern California Region	1	06-15-2011 04:39 PM
FS: Ichiba V1 Stud Replacement 20mm Wheel Spacers	toxik	Parts for sale (Private Classifieds)	9	01-19-2011 06:11 PM
2Ea. 20mm Ichiba Wheel Spacers V2	neveucd	Parts for sale (Private Classifieds)	3	08-11-2010 10:29 PM
Ichiba V2 bolt-on 20mm for front wheels -- fits?	///M-Power	Wheels & Tires	0	09-03-2009 01:48 PM