The "Will it fit?" thread

redondoaveb · 10-25-2017, 07:42 PM

Quote:

Originally Posted by jchammond

That’s a soft,Mean looking Tire!

I got a good price on them with the discount that discount tires has right now on their ebay store. Wheels and tires are being delivered tomorrow, just in time to get them installed before my car goes in on Tuesday for the new supercharger tune.

redondoaveb · 10-27-2017, 08:21 PM

I test fit my wheels and tires today. 20x10 +22 front and 20x11 +28 rear with 255/35 front and 305/30 rear. Car is in the shop getting the supercharger installed. There are a bunch of parts off the car including trans (new clutch). Car is up on 4 post lift. We set the car on the ground and the rear is fine, tires are a little tucked in the wheel wells but I have about a half inch of poke outside of the wheel wells on the front. I know the suspension isn't settled and if the camber will change any when settled. I'm currently set at -1.4 camber front. I'm wondering if I need to run more negative camber or if I need to go to a 9" wheel and or a different offset.

k67p67 · 10-27-2017, 09:36 PM

A 20mm spacer in the rear would match the fit of the front wheels.

redondoaveb · 10-27-2017, 09:55 PM

Quote:

Originally Posted by k67p67

A 20mm spacer in the rear would match the fit of the front wheels.

I might go a small spacer in the rear but I'd like to keep the wheels tucked under the fender.

k67p67 · 10-27-2017, 10:06 PM

With a 20mm spacer in the rear, your new setup would look like this (technically 2mm more aggressive). This is 19x10 +24 and 19x11 +10.

redondoaveb · 10-27-2017, 10:17 PM

Quote:

Originally Posted by k67p67

With a 20mm spacer in the rear, your new setup would look like this (technically 2mm more aggressive). This is 19x10 +24 and 19x11 +10.

That looks good. I had 20mm spacers on my sport rays I just took off. I can put them on and see how it looks. Just out of curiosity, what camber are you running in the front?

k67p67 · 10-27-2017, 10:30 PM

Not sure. It is fairly close to spec. West End Alignment corner-balanced it and I didn't receive any measurement sheet.

10-27-2017, 09:36 PM	#3 (permalink)
k67p67 Enthusiast Member Join Date: Oct 2016 Location: Rancho Cucamonga, CA Posts: 312 Drives: 2017 Nismo Tech 6MT Rep Power: 3937	A 20mm spacer in the rear would match the fit of the front wheels. __________________ SOLD2017 370Z Nismo Tech 6MT PART OUT IN PROGRESS Work \| Motordyne \| Powertrix \| Swift \| Michelin \| Takeda \| Hotchkis \| RJM \| Voodoo13 \| SPL \| SPC \| Z1 Motorsports \| ZSpeed \| Morimoto \| Craft Square

10-27-2017, 10:06 PM	#5 (permalink)
k67p67 Enthusiast Member Join Date: Oct 2016 Location: Rancho Cucamonga, CA Posts: 312 Drives: 2017 Nismo Tech 6MT Rep Power: 3937	With a 20mm spacer in the rear, your new setup would look like this (technically 2mm more aggressive). This is 19x10 +24 and 19x11 +10. __________________ SOLD2017 370Z Nismo Tech 6MT PART OUT IN PROGRESS Work \| Motordyne \| Powertrix \| Swift \| Michelin \| Takeda \| Hotchkis \| RJM \| Voodoo13 \| SPL \| SPC \| Z1 Motorsports \| ZSpeed \| Morimoto \| Craft Square

10-27-2017, 10:30 PM	#7 (permalink)
k67p67 Enthusiast Member Join Date: Oct 2016 Location: Rancho Cucamonga, CA Posts: 312 Drives: 2017 Nismo Tech 6MT Rep Power: 3937	Not sure. It is fairly close to spec. West End Alignment corner-balanced it and I didn't receive any measurement sheet. __________________ SOLD2017 370Z Nismo Tech 6MT PART OUT IN PROGRESS Work \| Motordyne \| Powertrix \| Swift \| Michelin \| Takeda \| Hotchkis \| RJM \| Voodoo13 \| SPL \| SPC \| Z1 Motorsports \| ZSpeed \| Morimoto \| Craft Square Last edited by k67p67; 10-27-2017 at 10:40 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Official The370Z "Hot Girls with Hot cars" thread NSFW 01.01.09	AK370Z	Gentleman's Club	187	01-12-2011 12:24 AM
why did the thread "Sharing a bad experience with my 370Z" get closed?	TheSnakeJake	Nissan 370Z General Discussions	1	03-26-2010 11:35 PM
Why there isn't a "Monterey Blue"370Z thread?	Devil Z	Nissan 370Z Photos / Spyshots / Video / Media Gallery	9	08-24-2009 01:55 PM
Official "Guess the Stig's Time" Thread	ResIpsa	Nissan 370Z General Discussions	11	07-27-2009 09:45 PM
Official "Nissan 370Z spotted in Japan" Thread	AK370Z	Nissan 370Z Photos / Spyshots / Video / Media Gallery	120	05-01-2009 09:30 AM

10-27-2017, 08:21 PM	#2 (permalink)
redondoaveb A True Z Fanatic Join Date: Apr 2017 Location: So. Commiefornia Posts: 6,370 Drives: 2014 Nismo Gunmetal Rep Power: 2684374	I test fit my wheels and tires today. 20x10 +22 front and 20x11 +28 rear with 255/35 front and 305/30 rear. Car is in the shop getting the supercharger installed. There are a bunch of parts off the car including trans (new clutch). Car is up on 4 post lift. We set the car on the ground and the rear is fine, tires are a little tucked in the wheel wells but I have about a half inch of poke outside of the wheel wells on the front. I know the suspension isn't settled and if the camber will change any when settled. I'm currently set at -1.4 camber front. I'm wondering if I need to run more negative camber or if I need to go to a 9" wheel and or a different offset.