EcuTek RaceRom Feature Request Thread !

[visconti]

Originally Posted by 7speed

If synchro rev match is programmed purely by ecu? Then can they program it in for us non sport models.

The sport module have additional hardware that allow that rev sync to happen.

EcuTek does have something called AUTO-BLIP which is a dumb down version of your rev sync.

John

[wstar]

From an NA 7AT perspective doing road courses:

1) Figure our 7AT torque management and how it interplays with the throttle tables and the 7AT's version of SychroRevMatch for shifting, so that we can tune up the speed and firmness of the shifts without making them jerky where they'd break traction at the rear during corner entry/exit.

2) (and this probably applies to 6MT as well?) - make it programmable for different rear end ratios and tire sizes so that SRM works correctly and the speedo reads correctly when those are non-stock. Don't really care about breaking VDC/TCS/ABLS (disabled anyways on track car), just as long as SRM + Speedo are ok.

3) Digital readout of temps on the dash: Oil, Water, and Trans. My understanding from going through the wiring/depinning mess is that the main gauge pod (the 3x big pods behind the steering wheel) is directly on the CANBUS, and then the 3 little gauges are driven indirectly by some other little protocol from that unit - so I get you may not be able to mess with the clock. Honestly, looking at the circuit board behind the little gauges, I suspect the RTC for time display is implemented right there next to the gauge.

But: I think the driver info display on the left (the little orange mono LCD screen) might be worth hacking on. If you can't control that display directly, you could at least display one temp to it I bet: it has a stock mode where it displays ambient air temp - maybe you could trick that into showing water, oil, or trans temp in its place?

In any case, I'm sure you know more about available display methods than I do. We really need all 3 temps (oil, water, 7AT trans) digitally, but if you can only display one by hacking the ambient display, maybe give an option in the editor to choose which of the three to display there. The use-case reasons for each of the 3 being important:

1) Oil Temp - seems lowest priority because we *do* have a gauge for this, but there are two reasons to hate the stock gauge: (a) It doesn't read below 140, which would be handy when warming up a car with a big oil cooler on cold days + (b) on a track car with a custom dash, that little oil temp gauge is the only reason you can't ditch the stock little-3-gauge thingy (unless you add your own separate oil temp sensor + gauge, while also leaving the stock one in place for the ECU to use...). It would just be really handy to get the ECU's oil temp data elsewhere and be able to toss out that little gauge cluster when customizing the dash in a track car.

2) Water temp - The little dots display is horrible and doesn't tell you crap, really. On the other hand, at least this one is easily readable by any OBD-II device on the industry-standard PID for it, so there are other workarounds for some people in some situations.

3) 7AT trans temp - this is critical for estimating fluid life, and precisely reading it is also critical for doing your own fluid changes. The TCM has the sensor and talks to the ECU over CAN. The factory Consult-III tool can display this temp, but AFAIK *nobody* has released anything to the aftermarket that's capable, and nobody has managed to dig up a secret PID that can be used with any normal OBD-II reader or whatever. The workaround is of course drilling and tapping the pan and running your own separate fluid temp gauge, and hoping that reads within a margin of error from the TCM's sensor placement for fluid change levels.

[wstar]

Oh more wishlist items, assuming you don't already have this:

Be sure it's able to disable the check engine lights for removing non-essential equipment (e.g. when you gut the AC system, the radio system, etc - those throw various codes). With the Other Vendor, it's a matter of disabling specific error codes to keep the CEL clean for real problems. Bonus points if you can give us a *full* security system disable, meaning either or both of these things:

1) No need for a keyfob or the main fobgina unit at all - can disconnect all keyfob sensors/units and anytime the battery is hooked up, the start/stop button Just Works. As I understand it, this may require a little bit of custom wiring in addition to the ECU progamming, but if you could at least have a mode that works and give us clear instructions about it, that would be good enough (e.g. "Enable this option, then connect pin X on harness Y to pin Z on harness Foo, and ground this other wire over here...").
2) Ability to completely unplug/depin and remove the steering wheel lock module without the ECU throwing a security fit and requiring some hacky workaround that fakes like the module is still wired up to the car.

[wstar]

Was just re-thinking about temp displays above... if direct display of oil/water/trans is out, any chance your reflash could expose oil+trans temps on an unused PID number that normal OBD-II tools could be programmed to read? Maybe reuse some semi-standard PID numbers from other mfgs that do report those numbers?

[Chuck33079]

A solid release date for features?

[arnoldas]

when should we expect to see these features released?

[jrb55gh]

I would like to be able to see water, engine oil, 7at temps displayable on a street driven Z.

In addition displaying knock retard would aid in choosing the correct fuel and ignition timing for the street use.

[visconti]

Features are currently going under closed beta testing

Those of you who have EcuTek from me shoot me a PM or email for details

John

[Spikuh]

This may not be possible (or someone may have described this already), but I had a thought about map switching.

Add it to the list of functions that is handled on the left screen of the main cluster as opposed to loosing some other function (I think it is cruise control you lose with UpRev). Where the fuel gauge is.

[Seb@SZ]

Originally Posted by visconti

Features are currently going under closed beta testing

Those of you who have EcuTek from me shoot me a PM or email for details

John

Hi John

You have PM.

thanks

[Chuck33079]

Originally Posted by Spikuh

This may not be possible (or someone may have described this already), but I had a thought about map switching.

Add it to the list of functions that is handled on the left screen of the main cluster as opposed to loosing some other function (I think it is cruise control you lose with UpRev). Where the fuel gauge is.

You don't lose cruse control with Uprev. You just use the cruise control buttons to select the map.

[visconti]

check this out guys -

My new, unique mod for the GT-R - R35 GT-R - GT-R Life

[Rangerz]

Originally Posted by Chuck33079

You don't lose cruse control with Uprev. You just use the cruise control buttons to select the map.

Hey Chuck,

how do you tell which map is active out of the, 5 I think you can have with uprev

[Chuck33079]

Originally Posted by Rangerz

Hey Chuck,



how do you tell which map is active out of the, 5 I think you can have with uprev

I don't remember offhand. I've just got one map.

[Hotrodz]

When you set your maps the cruise control light will blink back at you 1 time if you set map one and 2 times for the next map and so on.