Uprev Tuning Info

roplusbee · 06-26-2012, 02:03 AM

I get my replacement ECU tomorrow morning and then off to the dyno for tuning. I am going to see if it is possible to run one map with etc on and another with it off. I haven't even seen the software yet, so I am running blind till later on. I am sure the tuner is going to be sick of my questions, lol!

Sent via Tapatalk 2 on my D-Team G-Slate

slynx · 06-27-2012, 07:21 PM

In for results! Very interested in the effect of etc on/off

Baer383 · 07-03-2012, 08:31 PM

I'm ordering my Uprev stuff next week but I don't know how much I'll be able to help I'm FI.

seymore4 · 07-03-2012, 10:54 PM

Quote:

Originally Posted by roplusbee

I am going to see if it is possible to run one map with etc on and another with it off.

The ETC control effects the entire tune, its not like the fuel, timing, or rev/speed limiter controls which are map specific, there's only one setting for all 5 maps. Same thing with the code deletion and fan engagement temp settings

zguynate · 07-09-2012, 09:19 PM

Hey pokey would you mind posting your current timing table?

roplusbee · 08-04-2012, 01:19 PM

So turning ETC off killed pretty much everything. Dave was able to adjust the torque table and that made it so that VDC was less invasive. Now I just have to get a cable and figure out which license upgrade to purchase so that I can remedy my pig rich condition. Cold/warm start it poor as well. Good luck contacting UPREV and getting a straight answer. I spoke with Rich about either getting tuned @ UPREV or getting a cable and license upgrade and he told me to email him. That was Tuesday and no response yet..............

Sent via Tapatalk 2 on my D-Team G-Slate

Baer383 · 08-04-2012, 01:32 PM

Quote:

Originally Posted by roplusbee

So turning ETC off killed pretty much everything. Dave was able to adjust the torque table and that made it so that VDC was less invasive. Now I just have to get a cable and figure out which license upgrade to purchase so that I can remedy my pig rich condition. Cold/warm start it poor as well. Good luck contacting UPREV and getting a straight answer. I spoke with Rich about either getting tuned @ UPREV or getting a cable and license upgrade and he told me to email him. That was Tuesday and no response yet..............

Sent via Tapatalk 2 on my D-Team G-Slate

Pm semore4 he got me my upgrade to tuner,tuning my car now.

seymore4 · 08-04-2012, 07:13 PM

Quote:

Originally Posted by Baer383

Pm seymore4 he got me my upgrade to tuner,tuning my car now.

Done and Done. Rich is cool and all but he does get distracted easily and isn't the best at following up with people... lol

Huck · 08-11-2012, 03:18 PM

God, all this tuning talk makes me want to buy my cable right now. Gotta save up for it

This all makes me sad, cause the tuner that did my car only changed A/F ratio to 13.1 and timing I think +1, and that was about it. He didn't do maps or anything... Now I just want to learn to do it myself and save some money.

Baer383 · 08-11-2012, 04:01 PM

Quote:

Originally Posted by Huck

God, all this tuning talk makes me want to buy my cable right now. Gotta save up for it

This all makes me sad, cause the tuner that did my car only changed A/F ratio to 13.1 and timing I think +1, and that was about it. He didn't do maps or anything... Now I just want to learn to do it myself and save some money.

I just got back from dailing in mine it is fun as sh!t

Huck · 08-11-2012, 04:39 PM

My only concern is blowing the motor lol. I just have to take it slow. I hope you guys don't mind when I start asking 4.5 metric tons of questions!

Z eliminator · 12-06-2012, 11:27 AM

What tables do you ajust the timing in ?
do you bump it 2 or 4 degress.
im new at this as i went from my wicked Cobb tune to uprev,because of the GTM tranney had to have an un prev flash.
Can you flash the tranney with uprev and put the cobb back on the ECU.
thanks

Z

Baer383 · 12-06-2012, 11:32 AM

Quote:

Originally Posted by Z eliminator

What tables do you ajust the timing in ?
do you bump it 2 or 4 degress.
im new at this as i went from my wicked Cobb tune to uprev,because of the GTM tranney had to have an un prev flash.
Can you flash the tranney with uprev and put the cobb back on the ECU.
thanks

Z

I have some new software where I copy and paste my timing map and it shows me the table in DBTDC

I don't think you will need the Cobb once you get use to tuning with Uprev.

Sh0velMan · 12-06-2012, 03:44 PM

Quote:

Originally Posted by Baer383

I have some new software where I copy and paste my timing map and it shows me the table in DBTDC

I don't think you will need the Cobb once you get use to tuning with Uprev.

Timing is pretty fickle on our cars tho. It will only actually add that timing if the knock sensor lets it.

In my car it is highly dependent on IAT and ECT whether I see -27deg or -17.

Baer383 · 12-06-2012, 03:53 PM

Quote:

Originally Posted by Sh0velMan

Timing is pretty fickle on our cars tho. It will only actually add that timing if the knock sensor lets it.

In my car it is highly dependent on IAT and ECT whether I see -27deg or -17.

They are,but for some reason even thou mine is FI it likes alott of timing till about 6k then it makes more power when the timing is pulled back after that.

06-26-2012, 02:03 AM	#46 (permalink)
roplusbee A True Z Fanatic Join Date: Dec 2009 Location: Killeen, TX Posts: 2,360 Drives: 2007 350Z NISMO Rep Power: 22	I get my replacement ECU tomorrow morning and then off to the dyno for tuning. I am going to see if it is possible to run one map with etc on and another with it off. I haven't even seen the software yet, so I am running blind till later on. I am sure the tuner is going to be sick of my questions, lol! Sent via Tapatalk 2 on my D-Team G-Slate __________________ 2007 350Z NISMO #0618: Zerolift \| UPREV \| F.I. \| Greddy \| Competition Clutch \| Injector Dynamics \| Aeromotive \| Pioneer \| JL

07-03-2012, 08:31 PM	#48 (permalink)
Baer383 A True Z Fanatic Join Date: Aug 2010 Location: Lawrenceville,Ga Posts: 4,293 Drives: My foot up your azz Rep Power: 30	I'm ordering my Uprev stuff next week but I don't know how much I'll be able to help I'm FI. __________________ 2013 ZL1 754 rwhp 747 rwtq

07-09-2012, 09:19 PM	#50 (permalink)
zguynate A True Z Fanatic Join Date: Jan 2012 Location: Strangeland Posts: 1,054 Drives: 09 370z Rep Power: 73	Hey pokey would you mind posting your current timing table? __________________ 2009 370z touring w/sports package

08-04-2012, 01:19 PM	#51 (permalink)
roplusbee A True Z Fanatic Join Date: Dec 2009 Location: Killeen, TX Posts: 2,360 Drives: 2007 350Z NISMO Rep Power: 22	So turning ETC off killed pretty much everything. Dave was able to adjust the torque table and that made it so that VDC was less invasive. Now I just have to get a cable and figure out which license upgrade to purchase so that I can remedy my pig rich condition. Cold/warm start it poor as well. Good luck contacting UPREV and getting a straight answer. I spoke with Rich about either getting tuned @ UPREV or getting a cable and license upgrade and he told me to email him. That was Tuesday and no response yet.............. Sent via Tapatalk 2 on my D-Team G-Slate __________________ 2007 350Z NISMO #0618: Zerolift \| UPREV \| F.I. \| Greddy \| Competition Clutch \| Injector Dynamics \| Aeromotive \| Pioneer \| JL

08-11-2012, 03:18 PM	#54 (permalink)
Huck A True Z Fanatic Join Date: Jan 2012 Location: Cocoa, Florida Age: 42 Posts: 5,075 Drives: Pantydropper machine Rep Power: 33	God, all this tuning talk makes me want to buy my cable right now. Gotta save up for it This all makes me sad, cause the tuner that did my car only changed A/F ratio to 13.1 and timing I think +1, and that was about it. He didn't do maps or anything... Now I just want to learn to do it myself and save some money. __________________ VLEDS \| Evo-R \| Moddiction \| CF Hood Struts \| F.I. CF CBE & LTH \| Stillen CAI \| NST Pulleys \| UpRev \| Z1 \| M7 \| Status \| Forgestar \| PSS \| Whiteline \| SPL \| SPC \| Kenwood \| Zenclosure \| Kicker \| Alpine Type R

06-27-2012, 07:21 PM	#47 (permalink)
slynx Base Member Join Date: Apr 2010 Location: Queens, NY Posts: 25 Drives: 370z 12 S 6MT Rep Power: 15	In for results! Very interested in the effect of etc on/off

08-11-2012, 04:39 PM	#56 (permalink)
Huck A True Z Fanatic Join Date: Jan 2012 Location: Cocoa, Florida Age: 42 Posts: 5,075 Drives: Pantydropper machine Rep Power: 33	My only concern is blowing the motor lol. I just have to take it slow. I hope you guys don't mind when I start asking 4.5 metric tons of questions! __________________ VLEDS \| Evo-R \| Moddiction \| CF Hood Struts \| F.I. CF CBE & LTH \| Stillen CAI \| NST Pulleys \| UpRev \| Z1 \| M7 \| Status \| Forgestar \| PSS \| Whiteline \| SPL \| SPC \| Kenwood \| Zenclosure \| Kicker \| Alpine Type R

12-06-2012, 11:27 AM	#57 (permalink)
Z eliminator A True Z Fanatic Join Date: Jul 2009 Location: Ontario Canada Posts: 1,659 Drives: 370 Z 7AT Sports Rep Power: 19	What tables do you ajust the timing in ? do you bump it 2 or 4 degress. im new at this as i went from my wicked Cobb tune to uprev,because of the GTM tranney had to have an un prev flash. Can you flash the tranney with uprev and put the cobb back on the ECU. thanks Z __________________ 12.343 @114.14 . 4.5 stroker motor is now being built. Dec 1 2015.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Uprev e-tune vs dyno tuning with uprev??	babbagandu	Tuning	6	05-07-2012 11:53 PM
Uprev Tuning Specials at R/T Tuning	Erik@RTTuning	Drivetrain/Engine	5	02-03-2012 10:55 AM
Kaizen Tuning, Acton MA UpRev Tuning	Kaizen Tuning	North East Region	0	07-12-2011 12:31 AM
Need more info about tuning	Diocletian	Tuning	7	06-12-2010 02:48 PM