Real Time Scanning, Code Clearing, Performance Monitoring, Aeroforce Scan Gauge Part2

JMac88 · 12-05-2010, 02:11 PM

I was hoping to have pictures of this in the dash before doing this new post but unfortunately my installer has been way to busy. This update is in a new thread to get all the information in one post, but also to try and get more support for the gauge. I am hoping the more descriptive title will attract more attention.

The Aeroforce gauge is an all in one gauge. I have been using them on all my cars for a while, and when I found out that they started supporting Nissan vehicles i jumped all over it. Its very easy to install. It gathers all the information and power from a single connection to your OBD2 Port. The OBD2 port will support up to 3 gauges which works perfect for the 370z.

Below is a list of parameters that have been tested and working on our cars.

WIDEBAND A/F RATIO – Taken from factory wideband O2 sensors
INTAKE AIR- Intake Air Temperature
COOLANT TEMP- Engine Coolant Temperature
INTAKE VALVE TIMING - valve timing in degrees
RPM- engine Revolutions Per Minute
MAF SENSOR VOLTS - raw voltage of mass air flow sensor
INJECTOR PULSE WIDTH
FUEL TEMPERATURE - measured at the tank
THROTTLE POS PCT- Throttle Position percentage (0-100%)
CATALYTIC CONVERTER TEMP BANK 1
CATALYTIC CONVERTER TEMP BANK 2
IGNITION ADVANCE- ignition timing advance
SHORT TRIM B1-short term fuel trim bank#1
SHORT TRIM B2-short term fuel trim bank#2
LONG TRIM B1-long term fuel trim bank#1
LONG TRIM B2-long term fuel trim bank#2
BATTERY VOLTAGE- Alternator/battery output voltage
ENGINE LOAD-calculated Engine Load (0-100%)
ENGINE RUN TIME - minutes since ignition was turned on
READ AND CLEAR DTC CODES
WARNING LIGHTS - commonly used with RPM for a shift light, but can be used with any of the listed parameters.
PERFORMANCE MONITORING - 0-60 time, 1/8th and 1/4 mile, ect...

There are also 2 ANALOG INPUTS on the back of the gauge. You can attach extra sensors to monitor parameters not scanned by the car. The kits include wideband sensors if you do not trust the factory ones, oil pressure, fuel pressure, boost sensor, EGT kits, temperature sensor kits, and a nitrous sensor.

These parameters were not working when tested on my car.
MAF SENSOR LB/M- Mass Air Flow (lbs/min) (They know its because we have dual mafs. Should not be hard to correct)
AMBIENT AIR TEMP - air temperature before the air filter, may be outside ambient or engine bay temp. (linked to maf sensor)
Miles Per Gallon – instantaneous fuel economy (linked to maf sensor)
Calculated net horsepower (linked to maf sensor)
INJECTOR DUTY CYCLE – 0-100%
TRANSMISSION RATIO - CVT transmission (while these say CVT, may still work with A/T trans)
TORQUE RATIO - CVT transmission
PRIMARY TRANSMISSION OIL PRESSURE
SECONDARY TRANS OIL PRESSURE
TRANS TEMP- Transmission Temperature (gas powered automatics including CVT)
Manual fan control - allows you to turn your fans on while the car is off.

The guys at Aeroforce are looking for are looking for a test car in the North Ridge, OH area. Send me a PM if your interested and I will get you in touch with them.

I also know the pricing they are going to be offering on 3 gauges. Its VERY good. But before i post the price i will need to talk to AK. I know that they would like to become a sponsor for the site, but they would like to see what kind of support they can get for the gauge before they do so as it is pricey to become a vendor. Talked to AK, and got an OK for pricing. $550 for 3 gauges

If you are somewhat interested in a gauge like this for our cars, please post your support. The pricing for what you get is unbeatable.

As a small tribute to the community, they will be programming our "z" logo into the start up screen. Below are pics of the gauge temporarily mounted in my car.

puckshaw · 12-05-2010, 02:46 PM

I'm still interested.

wheee! · 12-05-2010, 06:00 PM

subscribed...!

Staples · 12-06-2010, 10:11 AM

Great info, JMac. I'm sure there's going to be a good amount of support, especially on how easy the install actually is. I'm going to give them a call today and see if they're willing to give Infiniti some love too.

JMac88 · 12-06-2010, 02:14 PM

Talked to AK, He said i could post the price...

$550 for 3 gauges...

smoking deal IMO

Hey Staples, I have been talking with them about Infiniti support too. They see no reason why it will not carry over

wheee! · 12-06-2010, 02:23 PM

You mean a 3 gauge cluster to replace the factory setup, with each gauge displaying up to two separate parameters simultaneously from the same OBDII feed? WOW!

Jordo! · 12-06-2010, 03:28 PM

Do we need three gauges? Can't you toggle between all parameters using one?

JMac88 · 12-06-2010, 04:29 PM

You don't need 3. I am thinking most people would want 3 to replace the 3 gauges. If you wanted only one to mount somewhere else in the vehicle you can do that too.

Pretty sure the price on 1 is $249.

Staples, they have a g37 going in as a test car is that you? They are still looking for a 370 too

Jordo! · 12-06-2010, 05:37 PM

Quote:

Originally Posted by JMac88

You don't need 3. I am thinking most people would want 3 to replace the 3 gauges. If you wanted only one to mount somewhere else in the vehicle you can do that too.

Pretty sure the price on 1 is $249.

Staples, they have a g37 going in as a test car is that you? They are still looking for a 370 too

Okay -- cool. I'd be interested in one mounted somewhere as an extra guage as in the photo above.

christian370z · 12-06-2010, 06:37 PM

This looks great, I am definitely interested. Hopefully I will find a good location for an extra gauge as I do not want to mess with the dash just yet in terms of reaching the OEM gauges.

wheee! · 12-06-2010, 06:47 PM

Anyone hear of an A Pillar solution yet?

JMac88 · 12-06-2010, 09:31 PM

new A-Pillar would be nice, but i think most companies are steering clear because of the air bags

Something like Zats set-up would be nice with just one.
http://www.the370z.com/members/zat_z...fi-pillar.html

wishihadnav · 12-07-2010, 05:07 PM

great price!..maybe they can work in a deal for the sensors..ie boost, egt, etc..

Jordo! · 12-07-2010, 05:47 PM

Any chance of compiling a listing of folks who want one vs 3 and working out a deal for each group?

Count me in for 1

Also, it looks like each gauge can display two parameters at a time -- is that correct?

JMac88 · 12-07-2010, 09:08 PM

Quote:

Originally Posted by wishihadnav

great price!..maybe they can work in a deal for the sensors..ie boost, egt, etc..

I will talk to them about this as this thought has crossed my mind too.

Quote:

Originally Posted by Jordo!

Also, it looks like each gauge can display two parameters at a time -- is that correct?

That's correct. You can have the displays cycle through data if you wish too.

12-05-2010, 02:11 PM	#1 (permalink)
JMac88 Enthusiast Member Join Date: Jun 2010 Location: Edmonton AB Posts: 416 Drives: 2010 PW 370z Rep Power: 15	Real Time Scanning, Code Clearing, Performance Monitoring, Aeroforce Scan Gauge Part2 I was hoping to have pictures of this in the dash before doing this new post but unfortunately my installer has been way to busy. This update is in a new thread to get all the information in one post, but also to try and get more support for the gauge. I am hoping the more descriptive title will attract more attention. The Aeroforce gauge is an all in one gauge. I have been using them on all my cars for a while, and when I found out that they started supporting Nissan vehicles i jumped all over it. Its very easy to install. It gathers all the information and power from a single connection to your OBD2 Port. The OBD2 port will support up to 3 gauges which works perfect for the 370z. Below is a list of parameters that have been tested and working on our cars. WIDEBAND A/F RATIO – Taken from factory wideband O2 sensors INTAKE AIR- Intake Air Temperature COOLANT TEMP- Engine Coolant Temperature INTAKE VALVE TIMING - valve timing in degrees RPM- engine Revolutions Per Minute MAF SENSOR VOLTS - raw voltage of mass air flow sensor INJECTOR PULSE WIDTH FUEL TEMPERATURE - measured at the tank THROTTLE POS PCT- Throttle Position percentage (0-100%) CATALYTIC CONVERTER TEMP BANK 1 CATALYTIC CONVERTER TEMP BANK 2 IGNITION ADVANCE- ignition timing advance SHORT TRIM B1-short term fuel trim bank#1 SHORT TRIM B2-short term fuel trim bank#2 LONG TRIM B1-long term fuel trim bank#1 LONG TRIM B2-long term fuel trim bank#2 BATTERY VOLTAGE- Alternator/battery output voltage ENGINE LOAD-calculated Engine Load (0-100%) ENGINE RUN TIME - minutes since ignition was turned on READ AND CLEAR DTC CODES WARNING LIGHTS - commonly used with RPM for a shift light, but can be used with any of the listed parameters. PERFORMANCE MONITORING - 0-60 time, 1/8th and 1/4 mile, ect... There are also 2 ANALOG INPUTS on the back of the gauge. You can attach extra sensors to monitor parameters not scanned by the car. The kits include wideband sensors if you do not trust the factory ones, oil pressure, fuel pressure, boost sensor, EGT kits, temperature sensor kits, and a nitrous sensor. These parameters were not working when tested on my car. MAF SENSOR LB/M- Mass Air Flow (lbs/min) (They know its because we have dual mafs. Should not be hard to correct) AMBIENT AIR TEMP - air temperature before the air filter, may be outside ambient or engine bay temp. (linked to maf sensor) Miles Per Gallon – instantaneous fuel economy (linked to maf sensor) Calculated net horsepower (linked to maf sensor) INJECTOR DUTY CYCLE – 0-100% TRANSMISSION RATIO - CVT transmission (while these say CVT, may still work with A/T trans) TORQUE RATIO - CVT transmission PRIMARY TRANSMISSION OIL PRESSURE SECONDARY TRANS OIL PRESSURE TRANS TEMP- Transmission Temperature (gas powered automatics including CVT) Manual fan control - allows you to turn your fans on while the car is off. The guys at Aeroforce are looking for are looking for a test car in the North Ridge, OH area. Send me a PM if your interested and I will get you in touch with them. I also know the pricing they are going to be offering on 3 gauges. Its VERY good. But before i post the price i will need to talk to AK. I know that they would like to become a sponsor for the site, but they would like to see what kind of support they can get for the gauge before they do so as it is pricey to become a vendor. Talked to AK, and got an OK for pricing. $550 for 3 gauges If you are somewhat interested in a gauge like this for our cars, please post your support. The pricing for what you get is unbeatable. As a small tribute to the community, they will be programming our "z" logo into the start up screen. Below are pics of the gauge temporarily mounted in my car. __________________ Full Mod List Last edited by JMac88; 12-07-2010 at 10:42 AM.

12-05-2010, 06:00 PM	#3 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	subscribed...! __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

12-06-2010, 10:11 AM	#4 (permalink)
Staples Track Member Join Date: Sep 2010 Location: Baltimore, MD Posts: 546 Drives: '08 Infiniti G37s Rep Power: 16	Great info, JMac. I'm sure there's going to be a good amount of support, especially on how easy the install actually is. I'm going to give them a call today and see if they're willing to give Infiniti some love too. __________________ '08 Infiniti G37s - Forced Induction Fed

12-06-2010, 02:14 PM	#5 (permalink)
JMac88 Enthusiast Member Join Date: Jun 2010 Location: Edmonton AB Posts: 416 Drives: 2010 PW 370z Rep Power: 15	Talked to AK, He said i could post the price... $550 for 3 gauges... smoking deal IMO Hey Staples, I have been talking with them about Infiniti support too. They see no reason why it will not carry over __________________ Full Mod List

12-06-2010, 02:23 PM	#6 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	You mean a 3 gauge cluster to replace the factory setup, with each gauge displaying up to two separate parameters simultaneously from the same OBDII feed? WOW! __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

12-05-2010, 02:46 PM	#2 (permalink)
puckshaw Track Member Join Date: Nov 2009 Location: Charlotte, NC Posts: 620 Drives: 09 PW 370Z Touring Rep Power: 17	I'm still interested.

12-06-2010, 03:28 PM	#7 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 418	Do we need three gauges? Can't you toggle between all parameters using one? __________________ Enjoy it. Destroy it.

12-06-2010, 04:29 PM	#8 (permalink)
JMac88 Enthusiast Member Join Date: Jun 2010 Location: Edmonton AB Posts: 416 Drives: 2010 PW 370z Rep Power: 15	You don't need 3. I am thinking most people would want 3 to replace the 3 gauges. If you wanted only one to mount somewhere else in the vehicle you can do that too. Pretty sure the price on 1 is $249. Staples, they have a g37 going in as a test car is that you? They are still looking for a 370 too __________________ Full Mod List Last edited by JMac88; 12-06-2010 at 04:31 PM.

12-06-2010, 06:37 PM	#10 (permalink)
christian370z A True Z Fanatic Join Date: Jul 2010 Location: Newport Beach Posts: 3,900 Drives: 2010 370Z/Saab 900se Rep Power: 432	This looks great, I am definitely interested. Hopefully I will find a good location for an extra gauge as I do not want to mess with the dash just yet in terms of reaching the OEM gauges. __________________ -320whp / 259wftlbs- SP Rays -- RE-11s -- SpecialtyZ Tune -- Swift Springs -- Stillen 25R Oil Cooler -- Stillen G3 Intakes -- Berk HFCs -- F.I. 12" CBE -- Stillen Sway Bars -- Es14 Spring -- INGS+1 lip -- CF Spoiler -- GTR Start Button -- VLED Parking Lights -- PWJDM V2 shift knob

12-06-2010, 06:47 PM	#11 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	Anyone hear of an A Pillar solution yet? __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

12-06-2010, 09:31 PM	#12 (permalink)
JMac88 Enthusiast Member Join Date: Jun 2010 Location: Edmonton AB Posts: 416 Drives: 2010 PW 370z Rep Power: 15	new A-Pillar would be nice, but i think most companies are steering clear because of the air bags Something like Zats set-up would be nice with just one. http://www.the370z.com/members/zat_z...fi-pillar.html __________________ Full Mod List Last edited by JMac88; 12-06-2010 at 09:34 PM.

12-07-2010, 05:07 PM	#13 (permalink)
wishihadnav A True Z Fanatic Join Date: Nov 2009 Location: 90090 Posts: 1,851 Drives: Force Fed Nismo Rep Power: 184	great price!..maybe they can work in a deal for the sensors..ie boost, egt, etc..

12-07-2010, 05:47 PM	#14 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 418	Any chance of compiling a listing of folks who want one vs 3 and working out a deal for each group? Count me in for 1 Also, it looks like each gauge can display two parameters at a time -- is that correct? __________________ Enjoy it. Destroy it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Scan Gauge II Help	BernieB	DIY Section (Do-It-Yourself)	7	10-04-2011 09:05 AM
Product Announcement HKS CAMP2 Real-Time Engine Monitoring	Slidefox	Forced Induction	8	07-09-2011 12:50 PM
Aeroforce Interceptor	JMac88	Tuning	52	12-28-2010 11:59 AM
OBD II real-time monitor causing problems?	toon_herit	Nissan 370Z General Discussions	6	02-22-2010 06:35 PM
How about a real time chat?	Pushing_Tin	The370Z.com Feedback, Suggestions & Questions	28	07-24-2009 12:04 AM