Nissan 370Z Forum
Page 3 of 6 12 3 45 Last »
Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)
-   Tuning (http://www.the370z.com/tuning/)
-   -   EcuTek Releases Phase 2 RaceRom !! (http://www.the370z.com/tuning/104020-ecutek-releases-phase-2-racerom.html)

visconti 05-30-2015 12:55 AM
Quote:
Originally Posted by BGTV8 (Post 3213373)
I have a load cell in the gear-lever of my sequential gear box (which will go into the Z34 at some stage) ... can I use this to trigger ignition/fuel cut so I can change up without lifting off the throttle ?? Is there any way I can feed this signal into the OEM ECU and EcuTek manage fuel/ignition cut

I was thinking I'd need Motec/Haltech for flat-shift ..........

Email me, I'm sure we can figure something out


Sent from my iPhone using Tapatalk

Elmo370z 05-30-2015 01:22 PM
Any qualified tuners in the tampa area?

Jsmith7861 05-31-2015 01:35 AM
After reading this thread, I am insanely excited to get home and get the Z finished up. As I said in the other thread Visconti, do you know of any tuners in the VA area through you? Or do you just make the trip? I am currently deployed, but whenever I get back I decided I will be using Ecutek instead of Uprev.

Elmo370z 05-31-2015 09:34 AM
I'm interested as well

visconti 05-31-2015 09:21 PM
Quote:
Originally Posted by Jsmith7861 (Post 3214136)
After reading this thread, I am insanely excited to get home and get the Z finished up. As I said in the other thread Visconti, do you know of any tuners in the VA area through you? Or do you just make the trip? I am currently deployed, but whenever I get back I decided I will be using Ecutek instead of Uprev.
Pureautomotive is one of our dealers - we make trips there and tune out of their shop

John

Japanjay 05-31-2015 09:56 PM
Quote:
Originally Posted by visconti (Post 3207157)
Ecutek is always accepting qualified tuners.

What I can tell you is I've been doing this type of Nissan tuning with ecutek on GTR for several years, a lot of the stuff that's in this software is due to my Involvement behind the scenes... Any skilled tuner can pick up this suite and tune your car but it's going to take a while for them to get a handle on the very advanced custom map stuff that some of us have been using on a daily basis for years.

I do make trips, need my expenses covered and some money in my pocket to make it worth it.. The more cars you have the cheaper it'll be per car.

I'm defiantly down to make a trip

John


Sent from my iPhone using Tapatalk
Shoot me a PM on cost of software per car, group of 5, max you can get done in a day, extra costs for your time. I might be able to get around 5 that would be interested in this.

Elmo370z 06-01-2015 11:37 PM
HOw would i go about getting Ecu Race Rom, besides having to flying you to florida and paying you on top of that?

nismonster 06-03-2015 09:02 AM
1 Attachment(s)
Hi Guys, wanted to share; I contacted EcuTek about if the phase 2 rom can adjust the SRM so that different gears (namely 4.08) can use SRM with full compatibility -- ie. no CEL after 100 mph and exact rev matching on downshifts.

According to an EcuTek rep, this is possible. He attached an image file that I'm guessing is the settings to plug into the ROM interface.

Here's the exact email he sent me:

Quote:
Originally Posted by EcuTek Rep
Upon further research and speaking to one of our development guys this has been done by one of our dealers in Japan, I have found a map in the phase 2 software that corrects the gear ratios (see attached screenshot) so to confirm, this can be done and has been done.
As excited as I am about this, I will probably wait for someone else to be the guinea pig. Let me know if anyone with SRM and 4.08 gears has used this rom to adjust these settings before.

visconti 06-03-2015 09:09 AM
Quote:
Originally Posted by nismonster (Post 3217611)
Hi Guys, wanted to share; I contacted EcuTek about if the phase 2 rom can adjust the SRM so that different gears (namely 4.08) can use SRM with full compatibility -- ie. no CEL after 100 mph and exact rev matching on downshifts.

According to an EcuTek rep, this is possible. He attached an image file that I'm guessing is the settings to plug into the ROM interface.

Here's the exact email he sent me:



As excited as I am about this, I will probably wait for someone else to be the guinea pig. Let me know if anyone with SRM and 4.08 gears has used this rom to adjust these settings before.
It's been in the software for over a year now

I've personally have done this on a few cars, and it 100% works.




John

gbrettin 06-03-2015 03:56 PM
Well, I think I know what my next purchase is... :)

Elmo370z 06-03-2015 06:15 PM
Any video proof of this working?

JARblue 06-03-2015 06:24 PM
Quote:
Originally Posted by Elmo370z (Post 3218062)
Any video proof of this working?
Video proof of the tune with 4.08 gears working with SRM?

I'm just playing devil's advocate here, but if you don't trust his statement that he has done it, are you really going to trust that the car in the video has 4.08 gears installed?

tommyguns 06-03-2015 08:37 PM
Well after a B A D experience with my preferred shop and this latest announcement by EcuTek I'm jumping ship from the shop and uprev. Heading over to M&S Performance on Long Island this Saturday, having the ART pipes installed and a Visconti tune, looking for 93 / 93 aggressive / 93 w/75 shot nitrous / valet. May do the flat foot shift and launch control, we'll see not really sure but I'm super excited. I'll be taking video's of the runs especially when we spray for the first time. I'll post up the results.

visconti 06-03-2015 10:19 PM
Quote:
Originally Posted by JARblue (Post 3218066)
Video proof of the tune with 4.08 gears working with SRM?

I'm just playing devil's advocate here, but if you don't trust his statement that he has done it, are you really going to trust that the car in the video has 4.08 gears installed?
Buy a tune and I'll let you make a video to post up ;)

Elmo370z 06-03-2015 10:26 PM
I will keep you in mind sir, def has my interest.


All times are GMT -5. The time now is 01:28 PM.
Page 3 of 6 12 3 45 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2