anyone installed Iq3 datalogger?
 

I have ordered an iq3 datalogger to get my laptimes, etc.... Trying to see where did you get the rpm signal etc or some of the settings... never used one before.
It will be here in about 2 weeks, and been thinking of places to install it. I will also be looking at quickrelease hub and steering wheel

http://sphotos-b.xx.fbcdn.net/hphoto...28749538_n.jpg

http://sphotos-a.xx.fbcdn.net/hphoto...40438776_n.jpg


My buddy's Z with OMP steering wheel:
http://sphotos-a.xx.fbcdn.net/hphoto...41263108_n.jpg

Thinking of something like this too:
http://cdn.racerpartswholesale.com/i...3817_popup.jpg

I've heard z1 has or had a 350z with one....


---
I am here: http://maps.google.com/maps?ll=34.157712,-118.465740

Looks like no one got one... I'll keep putting my progress on here....

It arrived last night:
http://sphotos-a.xx.fbcdn.net/hphoto...53486983_n.jpg

nice, baller system

yea this looks like a nice add on to someone whos already boosted....

im not there yet :shakes head:

I don't think he is FI... It's a track toy.

lol he's no where near FI. I think he just has intake, exhaust.

That's right I'm not FI, this is for lap timing, datalogger etc, will give you predicted lap timing, video overlay and analysis as well. I will be mounting it on the cubby hole for now.

I need help finding engine rpm signal wire. Iq3 racepak says it requires "

50% duty cycle, 5-18V square wave signal"

Anyone????

Thanks!!!

Do I tap into - side of an injector? Or ....... ??

https://www.dropbox.com/s/3n58r4zvyb...issan_370Z.pdf

This lists the Tach wire as - RED, AC, ECU Grey 32 pin plug, Pin 14

Hope this helps.

Thanks a lot I will try that and report back!!

Didn't get a chance to tap into the rpm signal wire for now but here is a first test fitment. Once I get a quick release hub and steering wheel it will go infront of the stock gauges and make it removable...

http://sphotos-b.xx.fbcdn.net/hphoto...95316966_n.jpg

http://sphotos-b.xx.fbcdn.net/hphoto...15247213_n.jpg

http://sphotos-a.xx.fbcdn.net/hphoto...61001238_n.jpg

http://sphotos-b.xx.fbcdn.net/hphoto...78183940_n.jpg

http://sphotos-b.xx.fbcdn.net/hphoto...69359477_n.jpg
went with these buttons for now as the tactile were very sensitive and it is what I was looking for

Ignore the wiring etc... didn't have time to clean it up late last night!

Won't this simply read off the OBDII port with a dongle of some kind.

I have one of these being fitted to my race car as it is under-going an analogue to digital conversion in our off-season and we've chosen to use a Haltech ECU and the Haltech badges the IQ3 as its "dash".

Inlcuded in my kit was a dongle that plugs into the Z34 OBDII port and I canthen plug wghat looks like a serial connector on the dash into the dongle.

I won;t have it all back in my hands until later in December and based on the IQ3 doc off the Haltech web-site, all I need are two config files for the dash, one for the Z34 and another for the race car ...

I'd be surprised if you'd need to patch into thw wiring as these kits are marketed as comppetition to the MoTeC CDL3 and that I know is plug and play with an OBDII connector.

Not sure if this helps ...

Thank's for the reply, I did not yet buy the odb2 module that plugs in right behind the dash. My friend bought a lot of these so I got one decently priced. I will be orderign the odb2 soon though and it is plug and play.

I still rather connect the RPM via the wire instead of odb2 based on refresh rates.... I will update again in a few days when I have time to finish things up. The GPS on this isn't the greatest, takes a few minutes to acquire a signal and it's best to have it outside the car..... might stick it on the hatch somewhere (magnetic) or just open the window and put it on the roof while at the track...

In for updates

I haven't ordered the ob2 module yet, my friend is pricing it out!! Next on order is their universal 4 sensor USM module and add an oil pressure sensor. The Iq3 will output it and I can setup warning lights etc!

bump! did u ever find where to tap for rpm signal?

Ron, sorry this was on the back burner, I did not tap into the rpm signal wire, I just ordered an obd2 Wire for the racepak, got lucky and found one on ebay for $280 just now, I still need to tap into the rpm signal wire.

I also bought a steering column upper cover so I can relocate my iq3 dash in front of the stock dash.
Here's a quick chop I am removing it from the center cubby hole to here:

https://sphotos-a.xx.fbcdn.net/hphot...86644813_n.jpg

https://fbcdn-sphotos-g-a.akamaihd.n...08808623_n.jpg

Also ordered one of these: Haltech IQ3 Dash Mounting Bracket Black Anodized Aluminum HT06 800 MB IQ3 | eBay
http://thmb.inkfrog.com/rsz.php?user...size=520&gap=0

this bracket is very expensive through racepak, I found that one very cheap... or you can make your own. I won't be able to do all this until 1-2 weeks, have a time attack this weekend so getting the car prepped.

Finally getting to relocating everything not finished yet:

https://scontent-b-lax.xx.fbcdn.net/...04&oe=54C14619

https://fbcdn-sphotos-g-a.akamaihd.n...a5a1b77d74927e

https://fbcdn-sphotos-a-a.akamaihd.n...6adcfb430e62c1

Lookin good man, ETA on Martin at the track?

I have to run this Thursday and car is far from done...... Fr Shootout by superstreet/import tuner.

Some updates, tachometer, shift lights and gear indicator have been programmed

http://tapatalk.imageshack.com/v2/14...dbbbbd324e.jpg

What does it use for those signals? CAN?

There is an obd2 cable you can buy extra, or you buy sensors but they are VERY expensive $300-450 each.... RPM signal you just tape into ECU rpm wire, pin 110.

Just having issues getting the obd2 to read right now will have to send it to manufacturer.