official 1/4 mile track times

FPenvy

driver mod.

__________________
324whp/258wtq AAM Tuned |F.I. NonRes CF CBE/NonRes TestPipes #373|UpRev Tuner|Akuma Motorsports Intakes|Z1 34 Row Oil Cooler

Huck

Àsshole!

Zdayz 2014!!

__________________

FPenvy

love you

__________________
324whp/258wtq AAM Tuned |F.I. NonRes CF CBE/NonRes TestPipes #373|UpRev Tuner|Akuma Motorsports Intakes|Z1 34 Row Oil Cooler

Huck

Hehe. But seriously, I need to know what I'm doing wrong. I tried blipping the throttle right before take off and starting from like maybe 2k rpm, no wheel spin. Then I tried revving at around 3500 and dumping the clutch and trying to modulate wheel spin. Got a **** load of wheel hop. Then I tried driving at around 5k and slipping the clutch. Couldn't get better than a 2.09 60'.

Zdayz 2014!!

__________________

TheBoomSpoon

Search, i remember a whole thread on this from the 6mt guys. I'm awesome at flooring it and flipping the paddle

I launch at about 1700 on 7at. My best 60ft is 1.920 so far.

Huck

I've searched and read a few different pages, I was just wondering if anyone here had any other tips or tricks. The general consensus to be launched at 3500 rpm, and drop the pressure in your tires to about 28 pounds.

Zdayz 2014!!

__________________

TheBoomSpoon

I leave my rears at 35. I tried 30 twice and same 60ft but slower trap for me.

Tadpole

Like they say at the drag strip. <If you're spinning you ain't winning>

__________________
Takeda TR3009P Short Ram Intakes, Custom Dual Exhaust, X-Piped with 18" Resonators & TopSpeed Axle Backs. EVO-R Led Third Foglight,

tranceformer

Huck, it's trial & error. Depends on the track conditions too. What kind of tires are you running? Camber? Suspension?

I got my best results doing it this way:

-Rear tire pressure = 25 psi (although I felt like I lost a mph or two this way)
-Do a quick 3-4 sec burnout (I'll take sh*t for this) - puts a little heat in the tires and gets all the water out of the grooves
-hold 4,000 to 5,000 RPM at the line - not easy to "hold steady" with the drive-by-wire, i usually end up kinda of bouncing it around there
-'quickly' let out the clutch (not dumping it, but not slowly slipping it either)
-the split second the rear starts to squat, put your foot into the gas pedal HARD. if you spin at this point then your run is FUBAR. If you get on the gas too late, you'll get wheelhop.

With factory suspension, Sport wheels & tires, stock clutch I managed to cut high 1.8x to low 1.9x 60ft launches. Best I ever ran was 1.85 60ft. This was at PBIR down here in Palm Beach, IMO a very sticky track.

Side note: I'll never forget the night I was running low 1.9x and a few high 1.8x 60ft launches and some random hot shot at the track was critiquing my time slips. He said that I "need to work on my launches" and I'll be able to get some faster times. I asked him what car he was driving that night.... "oh that GT-R over there is mine".

__________________
Ray
2009 370Z Base Sport 6MT / 12.860 @ 109.09mph / 1.921 60ft / street tires
official 1/4 mile track times

Huck

Thanks man I appreciate it, exactly what I was looking for.

Currently running Forgestar f14 11" in the back, Michelin PSS 305's, -2.6° camber I think. I just got camber arms in the mail today do those need to be installed and then camber should be like -1.6-1.8. I'll reload my trunk, drop a little tire pressure and see what happens.

Zdayz 2014!!

__________________

Huck

Lol, your story reminds me of the first time I went to this track. There was some kid with a Stang GT pulled up in the staging lane and talked with another Stang guy about my Z like I couldn't hear him. They were laughing at my "slow @ss jap shît" and how he was gonna burn me.

I smoked his *** 6-7 times that night. He wasn't happy.

Zdayz 2014!!

__________________

FPenvy

if you are dead set on better times then lose the camber.

i've thought of this many times but i DD my Z so it would hurt the overall drive of the car since it's set up for handling and it's too fun to throw into turns to change it. the Z is camber heavy in the rear so that mean less tire is contacting the track for traction on a drag strip launch. factor in the squat on the launch and you lose even more of the contact patch.

__________________
324whp/258wtq AAM Tuned |F.I. NonRes CF CBE/NonRes TestPipes #373|UpRev Tuner|Akuma Motorsports Intakes|Z1 34 Row Oil Cooler

Z eliminator

60 ft 1.800

Z

__________________
12.343 @114.14 . 4.5 stroker motor is now being built. Dec 1 2015.

Huck

Boom

Zdayz 2014!!

__________________

tranceformer

like presto said, camber can make a big difference. I've made good passes on factory alignment and for a while tried -1.0 rear camber. It didn't seem to help as much on track launches, but definitely helped a lot on the 'street'.

__________________
Ray
2009 370Z Base Sport 6MT / 12.860 @ 109.09mph / 1.921 60ft / street tires
official 1/4 mile track times