Keeping temps down on track?

Averying · 07-24-2023, 07:04 PM

Quote:

Originally Posted by Z is 4 ZEBRA!

When you cut out the parts of the bumper… did you fill in any of the gaps to make it look better? It was it a straight up hack-saw job haha

Also, with my stock bash bar, I’m not sure cutting the upper grill piece would be as effective

Sent from my iPhone using Tapatalk

SeeThruHead · 07-24-2023, 09:26 PM

Ducting!

Averying · 07-24-2023, 10:24 PM

Quote:

Originally Posted by SeeThruHead

Ducting!

Good find. HP Academy (same company as the people making that video) is one of my favorites. Their podcasts are super interesting for the tech nerds our there

Sent from my iPhone using Tapatalk

SeeThruHead · 07-26-2023, 08:32 PM

can you show how the greddy is plumbed?

Averying · 07-26-2023, 09:51 PM

Quote:

Originally Posted by KapitalZ

The effect of progressive engine cooling modifications that I've made to my car on engine oil temperature at the track:

1. OEM (no cooling mods) = 275° (limp mode)
2. 25 Row Setrab Oil Cooler = 257°F to 275°F
3. 25 Row + Mishimoto Performance Radiator + WaterWetter = 239°F to 257°F
4. 25 Row + Mishi Rad + GReddy Radiator Breather Tank = 221°F to 239°F

I also run a grill mesh guard to keep the cooler and rad clean (see pic) and an Evor CF rad shroud.

Didn’t realize the breather tank made such a big difference to water temps! Looks like a fairly simple and cheap upgrade for the future.

Sent from my iPhone using Tapatalk

Tedmeister · 07-27-2023, 07:54 PM

My radiator and oil cooler are separated, with ducting to both. Make sure there is space behind the cooler and radiator for the air to go. No matter how well you duct to force the air into them, if there is nowhere for the air to go, you
won't get the air flow for maximum cooling. I just moved my oil temp sensor
to the sandwich adapter, so I know the temps as the oil enters the block.
My temps maxed out at 190 with ambient temps around 95. I'm N/A though.

Averying · 07-27-2023, 08:19 PM

Quote:

Originally Posted by Tedmeister

My radiator and oil cooler are separated, with ducting to both. Make sure there is space behind the cooler and radiator for the air to go. No matter how well you duct to force the air into them, if there is nowhere for the air to go, you
won't get the air flow for maximum cooling. I just moved my oil temp sensor
to the sandwich adapter, so I know the temps as the oil enters the block.
My temps maxed out at 190 with ambient temps around 95. I'm N/A though.

Max temp of 190 is super impressive regardless of being N/A!

Sent from my iPhone using Tapatalk

SeeThruHead · 07-27-2023, 10:24 PM

Quote:

Originally Posted by KapitalZ

There's a good illustration of how it's plumbed on this CZP webpage: https://conceptzperformance.com/gred...908_p_8682.php

There's a bunch of extra parts required for plumbing that are not included in the standard GReddy kit but are shown on the GKTech kit webpage (where I bought the extra parts I needed separately): https://au.gktech.com/products/z34-3...wirl-pot-setup

The GKTech tank is essentially a copy of the Greddy tank. Greg Kruse at GKTech got me sorted with parts and installation advice for the GReddy tank, before his version was available. Note the GKTech kit webpage includes links to Assembly Guides.

See attached pic showing my GReddy tank attached to the firewall of my Z.

i think i'm going to buy this
but not sure how to do the caps

it looks like the instructions say you take the pressurized cap off the oem and put it on the swirl pot

but the location of that cap moved throughout the years.

maybe i will just email them for the proper plumbing setup.

SeeThruHead · 07-28-2023, 09:30 AM

from gktech:

Quote:

Essentially you would ignore the cap that is closest to the engine which would be a blanking cap.

So then you would put a blanking cap on the reservoir, move that pressurizes cap to the header tank, however, I don't think there would be much benefit on this setup as its already technically a swirl pot setup and you would need to run it higher then the tank, which I don't know if you will achieve, clearance wise.

So seems like there's no point

Elmo370z · 07-30-2023, 01:14 AM

Swirl
Pot isn’t necessary, nor is an radiator upgrade. Simple duct is all you need with a 34 row oil
Cooler. Im at 500whp give or take and don’t experience any overheating.

weebs25 · 12-26-2023, 11:41 AM

I did this setup last summer on my 09. I only ran 2 events with it but I can say I noticed a difference. I was having troubles with getting bubbles in my system then overflowing and sitting in the reservoir. The ease of install and stop of this was worth the couple hundred bucks to me! I didn’t climb over stock temps because of it. The prior few I had to take cool downs frequently.
Currently I’m working on ducting - like mentioned above I don’t want to go aftermarket radiator.

07-24-2023, 09:26 PM	#17 (permalink)
SeeThruHead Track Member Join Date: Jun 2020 Location: Toronto Posts: 716 Drives: Red '18 Sport Manual Rep Power: 23498	Ducting! danegrey likes this. __________________ My Build thread STH Build Plan Thread Images too big fix here

07-26-2023, 08:32 PM	#19 (permalink)
SeeThruHead Track Member Join Date: Jun 2020 Location: Toronto Posts: 716 Drives: Red '18 Sport Manual Rep Power: 23498	can you show how the greddy is plumbed? __________________ My Build thread STH Build Plan Thread Images too big fix here

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
high water temps at track (limp mode)	z510	Track / Autocross / Drifting / Dragstrip	5	06-04-2019 09:44 AM
Brake Temps at the track	DarkJak	Track / Autocross / Drifting / Dragstrip	7	06-24-2018 12:58 AM
Keeping N/A	SoFloZ	Engine & Drivetrain	9	04-19-2012 12:31 AM
Keeping a distance and still get cut off?	cjeezy	Nissan 370Z General Discussions	47	04-15-2011 01:32 AM
Solved! Greddy Twin Turbo oil temps 220 on track	jayfightmoves	Forced Induction	22	07-13-2010 12:22 AM

07-27-2023, 07:54 PM	#21 (permalink)
Tedmeister Base Member Join Date: Feb 2017 Location: Florida Posts: 68 Drives: 12 M6 Rep Power: 6776	My radiator and oil cooler are separated, with ducting to both. Make sure there is space behind the cooler and radiator for the air to go. No matter how well you duct to force the air into them, if there is nowhere for the air to go, you won't get the air flow for maximum cooling. I just moved my oil temp sensor to the sandwich adapter, so I know the temps as the oil enters the block. My temps maxed out at 190 with ambient temps around 95. I'm N/A though.

07-30-2023, 01:14 AM	#25 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	Swirl Pot isn’t necessary, nor is an radiator upgrade. Simple duct is all you need with a 34 row oil Cooler. Im at 500whp give or take and don’t experience any overheating.