Racing Seat Fitment help: Bride Zeta XL vs Recaro SPG XL

BettyZ · 10-18-2019, 12:04 AM

I tested buddyclub setup with sparco evo2L. Couldn't even get in the car. Buddyclub rails are twice as thick as sparco rails, the brackets raise the rails above OEM, and most importantly, the welds are not continuous and are also "Guangzhao" trash welds. I would not entrust my life to Buddyclub.

As for that shop... idk what a Mustang floor pan looks like, but the Z's has a lot of topography. OEM front bolt holes are 3/4" above the pan itself. Im just a mildly-gifted amateur myself, and I'm sure a dedicated shop could come up with a solution. But I'd want to see real numbers before I paid. One thing I learned from my experience is that millimeters really do count when it comes to vertical seat fitment.

Sent from my SM-G955U using Tapatalk

BettyZ · 10-18-2019, 12:09 AM

One other thing. After shaving the seat cushion, going for a fixed seat, and fabbing the lowest mount possible, I fit in the Z with a helmet. But...

I was so low that my pedal geometry was all screwed up. Had shift issues even with RJM v3 clutch pedal. And, I could not see over the hood or fenders. Had no idea where the front of the car was, to the point that I stopped using drive-thrus.

Sent from my SM-G955U using Tapatalk

OptionZero · 10-18-2019, 02:16 PM

Custom rails are on the table

Zewerr · 10-19-2019, 12:42 AM

I feel like Buddy Club rails with the right seat can successfully mount the seat low enough. I have Buddy Club rails with Corbeau FX1 Pros which is not the correct combination and have been looking at different seats to make something work. I've mostly been looking at the side mount positions and for seats that lack a flat bottom to add additional clearance. If you need a wide seat, though, I can see the Buddy Club rails as a limiting factor. But narrow seats can be mounted low if they are capable.

jchammond · 10-19-2019, 05:38 AM

Quote:

Originally Posted by BettyZ

One other thing. After shaving the seat cushion, going for a fixed seat, and fabbing the lowest mount possible, I fit in the Z with a helmet. But...

I was so low that my pedal geometry was all screwed up. Had shift issues even with RJM v3 clutch pedal. And, I could not see over the hood or fenders. Had no idea where the front of the car was, to the point that I stopped using drive-thrus.

Sent from my SM-G955U using Tapatalk

I’m gonna check out your seat today; as I’m 6’6” & 270’ish...mostly up top.

I’ve been following this thread,because the touring leather seats I have are a no-go

I removed the drivers seat from the 11’ model I had & drilled out the mounting legs from the rails- then had them cut down an inch all over & made do with it (lotta work)...better, but probably close to where cloth/base seats position.

OptionZero · 11-05-2019, 07:23 PM

Took a day off and put in a call with Wine Country Motorsports at Sonoma Raceway

gonna test out the whole goddamn Sparco lineup! they also have stock of Cobra and OMP

brought my helmet this time too

I must say i am pretty grateful that there are Sparco and Recaro distributors within a couple hours

if only there were a damn Bride showroom around here too

Spooler · 11-06-2019, 04:54 PM

Never even saw this thread. I am looking too. Need a Halo seat though. Thank god I am shorter. LOL

Rusty · 11-06-2019, 10:01 PM

Quote:

Originally Posted by Spooler

Never even saw this thread. I am looking too. Need a Halo seat though. Thank god I am shorter. LOL

One of a few times being vertically challenged pays off.

2011 Nismo#91 · 11-07-2019, 08:40 PM

Bride Zeta seats are not racing seats, they have no certificate, they are just aftermarket seats. The Recaro seats are FIA seats.

Bride's English website is terrible but they do say the following are certified seats, RACING series, which they say are FIA tested: PROFACE/MAXIS/GARDIS/ZODIA

Brendan · 11-08-2019, 08:59 AM

Is there a difference between fia compliance and fia certified?
The site states that the zeta and vios are compliant as well
https://bride-jp.com/en/seat/zeta/ZE..._XL_black.html
https://bride-jp.com/en/seat/vios/VI...lack_logo.html

OptionZero · 11-08-2019, 03:34 PM

sparco evo II QRT
Perfect fit. Harness holes clear shoulders

Only question is how to get it low

OptionZero · 11-08-2019, 11:57 PM

Anyone knows if the Bride XL sliders will work? Roughly the same width for QRT and the Zeta XL

Fwiw, the sparco dealer tells me Planted makes the sparco mount/sliders

Really wish the sparco came in red

Hotrodz · 11-09-2019, 11:34 AM

Quote:

Originally Posted by OptionZero

Anyone knows if the Bride XL sliders will work? Roughly the same width for QRT and the Zeta XL

Fwiw, the sparco dealer tells me Planted makes the sparco mount/sliders

Really wish the sparco came in red

Planted does and they are fairly low but you will still need to modify the floor if you want to use the slider.

OptionZero · 11-11-2019, 03:08 PM

Well this is interesting

https://bride-jp.com/en/news/2019/09...-products.html

They list a Bride Zeta IV XL as upcoming product, no further info

Wait and see. New design feature on the zeta IV is highlighted to be bigger harness holes so its worth checkin out

AlWakRa · 11-11-2019, 05:48 PM

Quote:

Originally Posted by OptionZero

Well this is interesting

https://bride-jp.com/en/news/2019/09...-products.html

They list a Bride Zeta IV XL as upcoming product, no further info

Wait and see. New design feature on the zeta IV is highlighted to be bigger harness holes so its worth checkin out

I saw Zeta 3 XL dimensions and it appears to be nearly the same dimensions as Cobra Imola GT I have, both are smaller outside than SPG XL, but as per diagrams, Imola GT match SPG internal sizing, Imola has a high harness hole.

Anyway, you tried the seats, so I would say go for the one you feel most comfortable in, as well as having a higher harness hole to install harness safely.

10-18-2019, 12:04 AM	#16 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 37 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	I tested buddyclub setup with sparco evo2L. Couldn't even get in the car. Buddyclub rails are twice as thick as sparco rails, the brackets raise the rails above OEM, and most importantly, the welds are not continuous and are also "Guangzhao" trash welds. I would not entrust my life to Buddyclub. As for that shop... idk what a Mustang floor pan looks like, but the Z's has a lot of topography. OEM front bolt holes are 3/4" above the pan itself. Im just a mildly-gifted amateur myself, and I'm sure a dedicated shop could come up with a solution. But I'd want to see real numbers before I paid. One thing I learned from my experience is that millimeters really do count when it comes to vertical seat fitment. Sent from my SM-G955U using Tapatalk Quicksilvers likes this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

10-18-2019, 12:09 AM	#17 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 37 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	One other thing. After shaving the seat cushion, going for a fixed seat, and fabbing the lowest mount possible, I fit in the Z with a helmet. But... I was so low that my pedal geometry was all screwed up. Had shift issues even with RJM v3 clutch pedal. And, I could not see over the hood or fenders. Had no idea where the front of the car was, to the point that I stopped using drive-thrus. Sent from my SM-G955U using Tapatalk Hotrodz and Quicksilvers like this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

10-18-2019, 02:16 PM	#18 (permalink)
OptionZero A True Z Fanatic Join Date: Apr 2011 Location: Sacramento Posts: 3,225 Drives: 15 370Z Nismo 6MT Rep Power: 214100	Custom rails are on the table Hotrodz likes this. __________________ OptionZero Build Thread

10-19-2019, 12:42 AM	#19 (permalink)
Zewerr Base Member Join Date: Jan 2019 Location: Tacoma, WA Posts: 45 Drives: 11 370Z 82/182 STU Rep Power: 6	I feel like Buddy Club rails with the right seat can successfully mount the seat low enough. I have Buddy Club rails with Corbeau FX1 Pros which is not the correct combination and have been looking at different seats to make something work. I've mostly been looking at the side mount positions and for seats that lack a flat bottom to add additional clearance. If you need a wide seat, though, I can see the Buddy Club rails as a limiting factor. But narrow seats can be mounted low if they are capable. Last edited by Zewerr; 11-08-2019 at 02:56 AM.

11-05-2019, 07:23 PM	#21 (permalink)
OptionZero A True Z Fanatic Join Date: Apr 2011 Location: Sacramento Posts: 3,225 Drives: 15 370Z Nismo 6MT Rep Power: 214100	Took a day off and put in a call with Wine Country Motorsports at Sonoma Raceway gonna test out the whole goddamn Sparco lineup! they also have stock of Cobra and OMP brought my helmet this time too I must say i am pretty grateful that there are Sparco and Recaro distributors within a couple hours if only there were a damn Bride showroom around here too Hotrodz and Spooler like this. __________________ OptionZero Build Thread

11-06-2019, 04:54 PM	#22 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,798 Drives: 2013 Nismo 370z Rep Power: 2684392	Never even saw this thread. I am looking too. Need a Halo seat though. Thank god I am shorter. LOL Rusty and Hotrodz like this.

11-07-2019, 08:40 PM	#24 (permalink)
2011 Nismo#91 A True Z Fanatic Join Date: Mar 2011 Location: NJ Posts: 2,400 Drives: slowly Rep Power: 40569	Bride Zeta seats are not racing seats, they have no certificate, they are just aftermarket seats. The Recaro seats are FIA seats. Bride's English website is terrible but they do say the following are certified seats, RACING series, which they say are FIA tested: PROFACE/MAXIS/GARDIS/ZODIA

11-08-2019, 08:59 AM	#25 (permalink)
Brendan Track Member Join Date: Apr 2013 Location: Colorado Posts: 640 Drives: Poor man's Porsche Rep Power: 542	Is there a difference between fia compliance and fia certified? The site states that the zeta and vios are compliant as well https://bride-jp.com/en/seat/zeta/ZE..._XL_black.html https://bride-jp.com/en/seat/vios/VI...lack_logo.html

11-08-2019, 03:34 PM	#26 (permalink)
OptionZero A True Z Fanatic Join Date: Apr 2011 Location: Sacramento Posts: 3,225 Drives: 15 370Z Nismo 6MT Rep Power: 214100	sparco evo II QRT Perfect fit. Harness holes clear shoulders Only question is how to get it low Hotrodz and Brendan like this. __________________ OptionZero Build Thread

11-08-2019, 11:57 PM	#27 (permalink)
OptionZero A True Z Fanatic Join Date: Apr 2011 Location: Sacramento Posts: 3,225 Drives: 15 370Z Nismo 6MT Rep Power: 214100	Anyone knows if the Bride XL sliders will work? Roughly the same width for QRT and the Zeta XL Fwiw, the sparco dealer tells me Planted makes the sparco mount/sliders Really wish the sparco came in red __________________ OptionZero Build Thread

11-11-2019, 03:08 PM	#29 (permalink)
OptionZero A True Z Fanatic Join Date: Apr 2011 Location: Sacramento Posts: 3,225 Drives: 15 370Z Nismo 6MT Rep Power: 214100	Well this is interesting https://bride-jp.com/en/news/2019/09...-products.html They list a Bride Zeta IV XL as upcoming product, no further info Wait and see. New design feature on the zeta IV is highlighted to be bigger harness holes so its worth checkin out __________________ OptionZero Build Thread

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] Red Bride/Recaro/Status Racing Seat	VDesi07	Parts for sale (Private Classifieds)	2	02-19-2015 09:59 AM
Bride Zeta 3 or Cusco Zeta 3 in CFRP	ckim64	Wanted	0	12-10-2014 04:02 PM
FS: Bride seat Rail; 370z Fitment	abakja1	Hawaii	14	06-17-2012 12:54 PM
[FOR SALE] Brand new Recaro SPG XL racing seat	Kyle@STILLEN	Parts for sale (Private Classifieds)	6	04-29-2011 11:42 PM
Racing Seat Brackets - Bride Gias	Equinox	Exterior & Interior	60	03-12-2011 05:11 PM