Track Day Chat

Rusty · 12-03-2020, 03:07 PM

Quote:

Originally Posted by justin_boy

gotcha! I just replaced lines so thats why i had that fluid in there cause i needed to fill it anyway, and has a higher boiling point than rbf 660.

also, should I replace front and rear, or just front?

any pads you recommend?

Replace both front and rear. I started out with EBC Yellowstuff pads. As I got faster. I switched to the Carbotech pads.

justin_boy · 12-03-2020, 03:24 PM

Quote:

Originally Posted by Rusty

Replace both front and rear. I started out with EBC Yellowstuff pads. As I got faster. I switched to the Carbotech pads.

sweet...looking at corbotech from z1, theres so many options. which pad type did you go with?

justin_boy · 12-03-2020, 03:31 PM

okay so i ordered xp12's for the front and xp10's for the rear

thank you gentlemen for all of the help!!!!

Rusty · 12-03-2020, 03:46 PM

Quote:

Originally Posted by justin_boy

okay so i ordered xp12's for the front and xp10's for the rear

thank you gentlemen for all of the help!!!!

That could be a bit much. I'm using the 10F/8R combo.

justin_boy · 12-03-2020, 03:52 PM

Quote:

Originally Posted by Rusty

That could be a bit much. I'm using the 10F/8R combo.

guys from z1 recommended, told me to be mindful while warming up and ill go through my rotors a little faster but im okay with all that

they said some people daily this combo

Rusty · 12-03-2020, 03:55 PM

Quote:

Originally Posted by justin_boy

guys from z1 recommended, told me to be mindful while warming up and ill go through my rotors a little faster but im okay with all that

they said some people daily this combo

Be prepared for the squeak when cold.

Hotrodz · 12-03-2020, 06:10 PM

I agree with Rusty I ran xp10 front and 8 in the back. They were plenty and they squeal like mad when they are cold. You may experience either a hard bite or no bite at all when they a cold. They also dust really bad if that is a thing for you!

Sent from my SM-G965U using Tapatalk

Spooler · 12-03-2020, 06:49 PM

Quote:

Originally Posted by Rusty

Be prepared for the squeak when cold.

RaceCar..... I love it when they squeal, just annoys the hell out of everyone around me. I just laugh.

justin_boy · 12-05-2020, 03:01 AM

Quote:

Originally Posted by Spooler

RaceCar..... I love it when they squeal, just annoys the hell out of everyone around me. I just laugh.

lol the squeak never gets old for me

justin_boy · 12-05-2020, 03:03 AM

Quote:

Originally Posted by Hotrodz

I agree with Rusty I ran xp10 front and 8 in the back. They were plenty and they squeal like mad when they are cold. You may experience either a hard bite or no bite at all when they a cold. They also dust really bad if that is a thing for you!

Sent from my SM-G965U using Tapatalk

yes i have to be mindful to warm them up, why would i get a hard bite? i though i would have to worry aboout no bite til up to temp

eh the dust doesnt bother me lol

Hotrodz · 12-07-2020, 11:44 AM

Quote:

Originally Posted by justin_boy

yes i have to be mindful to warm them up, why would i get a hard bite? i though i would have to worry aboout no bite til up to temp

eh the dust doesnt bother me lol

All I am saying is that until the brakes are up to temperature they are unpredictable as I have experienced them to not bite, ice mode or grab and stop on a dime. Just providing food for thought.

Sent from my SM-G965U using Tapatalk

justin_boy · 12-07-2020, 07:06 PM

Quote:

Originally Posted by Hotrodz

All I am saying is that until the brakes are up to temperature they are unpredictable as I have experienced them to not bite, ice mode or grab and stop on a dime. Just providing food for thought.

Sent from my SM-G965U using Tapatalk

I most definitely appreciate you, i just didnt understand the hard bite. Gotta be super mindful, thank you for that

i already have to take it easy for the first 10 min anyways cause of the nankang ar-1 i currently have

bpchaos · 12-08-2020, 02:41 PM

I run XP10/XP8. It always surprises me when I think they're too cold to work and you end up slamming the passenger into the dash. Also the squeal. I don't know how some of you deal with it but man is it high pitched lol.

///maestro · 01-06-2021, 03:59 PM

Anyone measure bump & droop when installing coilovers? Roll Center?

Here are some pics of my bump(full compression, no springs) and droop (full decompression).

Rear full droop:

Rear full bump:

Rear Ride height:

Front full droop:

Front full bump:

Front Ride height:

Measurements: (from the top of the center cap to the center-most part of the fender)
Rear:

Fully Compressed (no spring): 317.5 mm

Full droop: 444.5 mm

Ride height (car on ground with spring): 352.425mm

Front:

Fully Compressed (no spring): 311.15 mm

Full Droop: 444.5 mm

Ride Height: 342.9mm

I may raise the front a bit, looks like I'll need a swift spring to properly preload the fronts, If I go any higher, the springs become loose. Only way to tell is to do a corner balance which will hopefully happen after I get my half-cage done.

Rusty · 01-06-2021, 04:11 PM

Quote:

Originally Posted by ///maestro

Anyone measure bump & droop when installing coilovers? Roll Center?

Here are some pics of my bump(full compression, no springs) and droop (full decompression).

Rear full droop:

Rear full bump:

Rear Ride height:

Front full droop:

Front full bump:

Front Ride height:

Measurements: (from the top of the center cap to the center-most part of the fender)
Rear:

Fully Compressed (no spring): 317.5 mm

Full droop: 444.5 mm

Ride height (car on ground with spring): 352.425mm

Front:

Fully Compressed (no spring): 311.15 mm

Full Droop: 444.5 mm

Ride Height: 342.9mm

I may raise the front a bit, looks like I'll need a swift spring to properly preload the fronts, If I go any higher, the springs become loose. Only way to tell is to do a corner balance which will hopefully happen after I get my half-cage done.

When you did this. Did you watch to see how much the camber changes during full movement?

12-03-2020, 06:10 PM	#217 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	I agree with Rusty I ran xp10 front and 8 in the back. They were plenty and they squeal like mad when they are cold. You may experience either a hard bite or no bite at all when they a cold. They also dust really bad if that is a thing for you! Sent from my SM-G965U using Tapatalk Rusty, Mick_12Nismo, Spooler and 1 others like this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

12-08-2020, 02:41 PM	#223 (permalink)
bpchaos Base Member Join Date: Oct 2016 Location: Los Angeles, CA Posts: 74 Drives: G37S (370z+ seats) Rep Power: 3364	I run XP10/XP8. It always surprises me when I think they're too cold to work and you end up slamming the passenger into the dash. Also the squeal. I don't know how some of you deal with it but man is it high pitched lol. Rusty and Hotrodz like this.

01-06-2021, 03:59 PM	#224 (permalink)
///maestro Track Member Join Date: Dec 2014 Location: Grand Rapids, MI Posts: 530 Drives: 11' 370z\|09' BMW M3 Rep Power: 12	Anyone measure bump & droop when installing coilovers? Roll Center? Here are some pics of my bump(full compression, no springs) and droop (full decompression). Rear full droop: Rear full bump: Rear Ride height: Front full droop: Front full bump: Front Ride height: Measurements: (from the top of the center cap to the center-most part of the fender) Rear: Fully Compressed (no spring): 317.5 mm Full droop: 444.5 mm Ride height (car on ground with spring): 352.425mm Front: Fully Compressed (no spring): 311.15 mm Full Droop: 444.5 mm Ride Height: 342.9mm I may raise the front a bit, looks like I'll need a swift spring to properly preload the fronts, If I go any higher, the springs become loose. Only way to tell is to do a corner balance which will hopefully happen after I get my half-cage done. Rusty and Hotrodz like this. __________________ Gallo24 swapped 370z Instagram: @z34_motorsport

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Sacramento Meets/Chat	Cbtech	Northern California Region	1880	07-25-2016 02:01 PM
Midwest Chat Thread everyone is welcome!	erkthejerk73	Mid Western Region	745	02-19-2015 08:34 PM
Houston Chat Thread	d&g35	Texas	931	06-11-2013 08:03 PM

12-03-2020, 03:31 PM	#213 (permalink)
justin_boy Track Member Join Date: May 2015 Location: woodland hills Posts: 600 Drives: z34 Rep Power: 8367	okay so i ordered xp12's for the front and xp10's for the rear thank you gentlemen for all of the help!!!!