![]() |
Here, my saved list is easier. Front -2.9 camber, 0.05* toe out, 6.5 caster Rear -1.8 camber, 0.05* toe in 3080lbs, 1750lbs front, 1330lbs rear, no corner balance yet 2013
|
|
LinkBack | Thread Tools | Display Modes |
![]() |
#31 (permalink) |
A True Z Fanatic
Join Date: May 2013
Location: Columbus, OH
Posts: 5,051
Drives: 2013 Silver 370z
Rep Power: 3389 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Here, my saved list is easier.
Front -2.9 camber, 0.05* toe out, 6.5 caster Rear -1.8 camber, 0.05* toe in 3080lbs, 1750lbs front, 1330lbs rear, no corner balance yet 2013 Sport 6mt Engine---- OBX LTH with DEI titanium wrap Motordyne XYZ Y pipe with DEI titanium wrap Custom single 3" side exit exhaust, 1- 18" bottle res, 1 ultra quiet res, DEI titanium wrap Stillen gen 3 CAI with DEI gold wrap My dual AOS setup My PnP TB, upper and lower manifolds My 48 row oil cooler CJ motorsports large baffled oil pan Venting valve vents to atmos Gas tank cut in half for fuel starve fix Gas tank vent line with Boyd rollover vent/check valve Redline 5w30 oil CSF triple pass radiator Tuned by Crucial Performance Drive---- My rear 25 row diff cooler/Tilton pump with temp gauge SPL solid diff bushings Drop Eng. poly tranny mount Redline diff fluid Redline tranny fluid Z1 solid engine mounts Suspension---- Stance 2 way true type coilovers 18k/8k SPL toe links SPL traction arms SPL rear chamber arms Hotckins front sway bar OEM rear sway bar SPL camber arms front SPL rear knuckle bushings SPL front end links My rear eccentric lock out kit Traction and yaw kill switch Brakes----- Z1 SS brake lines Front brake cooling ducts Rear brake cooling ducts Rbf600 fluid Z1 2 piece rear rotors Z1 2 piece front rotors Carbotech XP12 front pads and XP10 rear pads ABS system delete with Wilwood proportional valve Aero---- My Front splitter My Canards My complete flat bottom My rear diffuser APR 71" GT-250 wing chassis mounted Vented upper bumper for CAI and top of radiator Wheels/tires RPF-1 18x10.5 +15 square but rear is -30 RS-3's 285/35/18 square 45mm rear spacer with 10.9 hardware 3" ARP extended rear wheel studs Safety OMP fiberglass FIA halo seat. OMP 6 point FIA belt with 2" shoulder straps for Hans device. Hans III device. OMP belt with 8.8 ring hardware 10.9 hardware holding seat to raisers and base. Planted FIA steel base Planted FIA aluminium raisers. FIA 1.75" roll cage Misc. Rear wide body fenders Deka 11lbs battery E-brake delete Full car air bag system delete All non essential wires deleted throughout Vinyl wrapped AC system deleted along with two pulleys Wanted. Wavetrac rear diff 275/35/18 A7's Spare set RPF1's Corner balance Wind tunnel
__________________
13 370z- Last edited by synolimit; 11-21-2016 at 05:33 AM. |
![]() |
![]() |
Bookmarks |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Post Your Track Setup! | RCZ | Track / Autocross / Drifting / Dragstrip | 42 | 11-26-2016 08:53 AM |
Which is a better Track Setup? | scruffydog | Wheels & Tires | 2 | 02-28-2013 07:58 PM |
Track Setup for KW V3s | scruffydog | Track / Autocross / Drifting / Dragstrip | 6 | 01-30-2013 02:29 PM |
KW v3 track setup | Nism0370 | Track / Autocross / Drifting / Dragstrip | 17 | 01-30-2013 12:45 AM |
Alignment for my track setup | Germanguy | Track / Autocross / Drifting / Dragstrip | 6 | 07-25-2012 05:42 PM |