My track day/time trial Nismo build....

wanabgts

My car has been doing really well on the overtired toyo's at around 34psi front, 30psi rear. Im going to be adding camber to the front for the next round, this is surface isn't all that high of grip so at other sites/track I should have more of a problem.

Zack

Zauskycop

Sounds about right for asphalt. I run 35F/30R and that seems to help the rear. I go about 3 lbs higher on (rare) concrete...

Tracy Ramsey

wanabgts

Ended up getting the car out for a SCCA Track Night in America event the second weekend of the month. Car performed very well for me all afternoon, temps are in check finally and the suspension setup is much better than last year.

Need to get my brake ducting and new pads and rotors on before the next outing, I never lost brakes but they were definitely being taxed on this day.

Ended up running a 1:24.9 at Portland International Raceway which is my best "road tire" time at this track. Highest straight speed was 149mph, also up 4.5mph from the last time out.

I'm confident there is 2 seconds in the car if I were to add a wing, so I'm struggling with how much of a "street car" I really want it to be. A battle which I usually lose and end up doing racecar stuff.







Zack

DannyGT

Single 24 row oil cooler works for you at that power? What are the max temps? hit limp mode at all?

__________________
Performance GTM Stage 1 SC, GTM Res.Test Pipes, Invidia Gemini Exhaust, GTM HD Oil Cooler
Wheels & Suspension AME Tracer TM02's 19x9.5F 19x10.5R w/ 265x35F & 305x30R, Hotchkis Sways, BC (BR) Racing Coilovers (Car Sold)

wanabgts

My 24 row is probably as small as I can run. Here is the list of stuff I have done to keep oil temps in check:

24 row cooler

7" shrouded fan on oil cooler, thermostatically controlled @160*

I run the pan spacer, and 1 qt overfull, so almost 7qts of oil total

Motul 300v, ester core seems to produce less heat when compressed

CSF radiator w/15% antifreeze and water wetter

The main thing for me has been running the car richer, 11:0 a/f vs. 11.6 a/f was almost 15 degrees in oil temps and a big difference in coolant as well.

I can maintain 260* oil temps now for over 25 min of running the car hard at 550whp. With the quality of oils and such now I don't think this is anywhere near unreasonable for 30min or less. And no I have never experienced limp mode.

Zack

Halfkiddio

260 degrees is about 20-30 degrees hotter than I would prefer to run, especially on a boosted Z. But that's just my personal preference.

wanabgts

Thermal breakdown is near 550 on modern oils, as long as you aren't running into detonation problems because of temp I think your all good to go. 240* is typically what I would shoot for as well, but modern cars do typically run much hotter.

5 years on this setup, stock engine, 500+whp for 3-7 track days a year.

Zack

Halfkiddio

Yea I agree it will be fine at 260, but I just feel that is somewhat high. But if its lasted this long at that level, then it should be fine. Like I said, that's just my personal preference to not run higher than 240 degrees or so.

Rusty

Which tune you running? Uprev, or Ecutec? Running at 260F it should be pulling timing.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

wanabgts

Sorry for the late up date guys, have only got to run the car twice in the last couple months. I ended up getting my brake ducts done finally, kind of a PITA with all of the charge piping, intakes, and oil cooler plumbing. I had to use the side vents, which I wasn't keen on doing. I decided that blocking them off completely will help with high pressure in the fender wells.

I used the Stillen mounting plates on the spindles, which fit well and made hooking up to the center of the rotor easy. I made the block of plates out of aluminum, and welded some bead rolled tube on to clamp the ducting to.

I plan on getting ARP studs in so I can run 10mm spacers in back. Im also working on rear downforce options that don't include a big wing.

Don't mind the munched splitter, I caught some debris.



Zack

Rusty

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

carlitos_370z

nice work man!!! you give me an idea to install brake ducts on my 2013+Z front bumper

wanabgts

Thank you sir!, Have to get creative with the plumbing sometimes!

Zack

carlitos_370z

Hell yeah! Im going finish a few things first but for my next track day Im going to work on the brake ducts

wanabgts

Well I got the car cleaned up to head to my home garage for Fall/winter season. I will be doing some work on the car over the winter. Planning on getting my trans/differential coolers installed, ducting, and hopefully the bushings replaced. The paint came out good, and got all the cone/rubber marks off from a year of racing!



Zack