Nissan 370Z Forum  

370Z Forums HOME My Picture Album Nissan 370Z Pictures Premium Membership Become a Forum Sponsor
Go Back   Nissan 370Z Forum > Search Forums
Reload this Page Search Results
Register All Albums FAQDonate Members List Calendar Today's Posts


Page 1 of 18 1 2311 Last »
Showing results 1 to 25 of 428
Search took 0.03 seconds. Search: Posts Made By: juld0zer
Forum: Engine & Drivetrain 11-07-2017, 06:14 AM
Replies: 22
Views: 6,838
Posted By juld0zer
Might have to take it to an auto electrician and...

Might have to take it to an auto electrician and ask them to scope the crank sensor for you.

Next step would be to inspect the tone ring on the flywheel - borescope and turn the engine over by...
Forum: Brakes & Suspension 11-07-2017, 05:50 AM
Replies: 12
Views: 1,930
Posted By juld0zer
Does the brake even work on that wheel? ie with...

Does the brake even work on that wheel? ie with the pressure bleeder at 15psi, can you rotate the wheel by hand?

How about when an assistant is standing on the brake pedal?
Forum: Engine & Drivetrain 10-27-2017, 08:42 PM
Replies: 207
Views: 63,520
Posted By juld0zer
I always thought it was throttle related because...

I always thought it was throttle related because i had a bug in my throttle map that would only randomly cause the severe lag where the revs increase extremely slowly. My guess is that the TPS or the...
Forum: Engine & Drivetrain 07-08-2017, 08:25 AM
Replies: 1,022
Views: 162,034
Posted By juld0zer
You cant do anything tuning-wise to reduce the...

You cant do anything tuning-wise to reduce the impact of heatsoak. The only solution is to address the heatsoak problem - insulate, reflect and relocate. Heatsoak is inevitable. You goal is to delay...
Forum: Engine & Drivetrain 07-06-2017, 08:20 AM
Replies: 1,022
Views: 162,034
Posted By juld0zer
Has anyone approached Nissan to do a software...

Has anyone approached Nissan to do a software update on the car or at least the ECU?

When i reflashed a different throttle map using Uprev, it cured it. Aside from the heatsoak issues but you need...
Forum: Engine & Drivetrain 01-26-2017, 07:44 PM
Replies: 169
Views: 91,690
Posted By juld0zer
lol folks it's 100-105Nm for cars with spring...

lol folks it's 100-105Nm for cars with spring washer and beer cap or 180-185Nm for what i assume is cars with just the nut and cotter pin.

It's been a while but i think i used 185Nm and then a big...
Forum: Engine & Drivetrain 01-04-2017, 07:40 PM
Replies: 169
Views: 91,690
Posted By juld0zer
I sold the car a few years ago. It was still good...

I sold the car a few years ago. It was still good by the time i sold it too
Forum: Engine & Drivetrain 11-17-2016, 08:20 AM
Replies: 207
Views: 63,520
Posted By juld0zer
So a bodgy throttle body harness extender was the...

So a bodgy throttle body harness extender was the cause?
Forum: Engine & Drivetrain 10-29-2016, 06:10 AM
Replies: 87
Views: 25,304
Posted By juld0zer
Get an oil cooler to begin with. Mine was a 2011...

Get an oil cooler to begin with. Mine was a 2011 model with the factory oil/water heat exchanger and even in our hot Aussie summers it rarely went over 100*c in normal driving
Forum: Engine & Drivetrain 10-07-2016, 09:21 AM
Replies: 1,022
Views: 162,034
Posted By juld0zer
ZeN, Please refer to my earlier posts. I...

ZeN,
Please refer to my earlier posts. I detailed exactly what you propose on doing. I have done it before and it works, and later on after a lot of research i went several steps further to restore...
Forum: Engine & Drivetrain 08-01-2016, 05:27 PM
Replies: 10
Views: 3,310
Posted By juld0zer
What was the outcome for this issue?

What was the outcome for this issue?
Forum: Engine & Drivetrain 04-19-2016, 07:28 AM
Replies: 22
Views: 15,074
Posted By juld0zer
You can get pretty cheap basic oscilloscopes...

You can get pretty cheap basic oscilloscopes these days that would help in this situation. Assuming everything electrically checks out you're left with a faulty ECU or mechanical fault, such as the...
Forum: Brakes & Suspension 03-13-2016, 03:45 PM
Replies: 49
Views: 15,759
Posted By juld0zer
Yep, i posted up a thread about it. You need a...

Yep, i posted up a thread about it. You need a castellated nut to replace the inadequate Nissan design. Easiest suitable replacement is the Kawasaki axle nuts but you need some thick washers to make...
Forum: Tuning 03-11-2016, 05:24 PM
Replies: 399
Views: 98,309
Posted By juld0zer
I don't think so. Just do the ecu reset procedure...

I don't think so. Just do the ecu reset procedure to clear the fuel trims.

If you have Uprev you could've datalogged the MAF sensors and compare the pair then replace and compare the new pair....
Forum: Engine & Drivetrain 02-17-2016, 09:39 AM
Replies: 169
Views: 91,690
Posted By juld0zer
The M77 grease is to be applied to the flat face...

The M77 grease is to be applied to the flat face of the outer CV only. Not the splines. The flat face is the face which butts up against the hub. It's approx 10mm wide. There is a TSB for the 370Z...
Forum: Engine & Drivetrain 12-22-2015, 01:29 AM
Replies: 77
Views: 36,771
Posted By juld0zer
For me, i did have the Stillen G3 fitted at the...

For me, i did have the Stillen G3 fitted at the time but i had it on for ages before it started happening. In the end, it was a bug in the throttle map i had loaded with Uprev. My guess is that under...
Forum: Engine & Drivetrain 12-21-2015, 09:20 AM
Replies: 77
Views: 36,771
Posted By juld0zer
Jerking and bucking sounds like dirty or...

Jerking and bucking sounds like dirty or contaminated MAF/s to me. Clean both MAF sensors using the correct cleaner aerosol and then do a battery reset and go for a drive.
Forum: Engine & Drivetrain 12-20-2015, 09:58 PM
Replies: 32
Views: 6,502
Posted By juld0zer
I dont have my Z anymore but what you can do is...

I dont have my Z anymore but what you can do is get a length of whipper snipper line and use that to simulate how you'll route it because a coathanger wont simulate the tendency of braided hose to...
Forum: Engine & Drivetrain 08-09-2015, 08:13 AM
Replies: 21
Views: 4,650
Posted By juld0zer
You have two choices: 1. Delete the factory...

You have two choices:
1. Delete the factory water/oil heat exchanger sandwich plate and just join the coolant lines together - but you must fit a thermostatic sandwich plate otherwise your oil takes...
Forum: Engine & Drivetrain 08-09-2015, 07:51 AM
Replies: 21
Views: 3,589
Posted By juld0zer
Warped upper manifold Digi?? Is that what was...

Warped upper manifold Digi?? Is that what was causing your power loss issues?

Damn man, i hope you have finally sorted it out.

When i fitted my Motordyne manifold for testing, i dont recall...
Forum: Engine & Drivetrain 08-09-2015, 07:41 AM
Replies: 11
Views: 3,527
Posted By juld0zer
relearn is a must. there is 3 relearns you must...

relearn is a must. there is 3 relearns you must do, and follow the steps to a T.
Forum: Engine & Drivetrain 08-09-2015, 07:36 AM
Replies: 82
Views: 12,563
Posted By juld0zer
the other guy was in the UAE. He had the cams...

the other guy was in the UAE. He had the cams installed then had some issues with post-installation. Can't remember his username but if you go back thru the threads and look for one with VVEL fault...
Forum: Engine & Drivetrain 08-09-2015, 07:31 AM
Replies: 9
Views: 1,952
Posted By juld0zer
Can you load the Stillen tune on to see what...

Can you load the Stillen tune on to see what happens? 553600rpm??
Forum: Engine & Drivetrain 07-16-2015, 05:57 AM
Replies: 11
Views: 2,422
Posted By juld0zer
I found that an oil with a high moly content...

I found that an oil with a high moly content definitely helped to reduce the valvetrain noise at 'higher' oil temps such as after a hard run
Forum: Engine & Drivetrain 07-14-2015, 03:19 AM
Replies: 207
Views: 63,520
Posted By juld0zer
Seems odd. These are low mileage cars yeah? I...

Seems odd. These are low mileage cars yeah?
I cleaned mine at approx 60000km (cant remember exact mileage before i sold it) and the amount of gunk on there was negligible. It was mostly just...
Showing results 1 to 25 of 428
Page 1 of 18 1 2311 Last »

 
Forum Jump

All times are GMT -5. The time now is 11:25 AM.

Contact Us - Home Page - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2