Complete Custom 3.5'' Exhaust

Megan370z · 12-01-2013, 10:27 AM

Updated info about the complete N/A Package Deal on post # 12

I'm wondering if anybody could be seriously interested into my custom exhaust.

the kit include the whole exhaust setup which is;

- Modified Momentum headers (not the z1 copy)
- Custom Y-Pipe 2.5'' paired with a transition & megaphone to 3.5'' single exit.
- Custom 3.5'' mid pipe with a 18'' resonator.
- Custom Muffler section 3.5'' in & out.
- 2x HFC (y-pipe)
- 2x Resonator (y-pipe)
- Custom rear holding bracket (with bolts)
- All mandrel bent 304SS tubing.
- TIG Welded and Back-Purged for improved stronger welds.
- Equipped with modified V-bands to reduce turbulence.
- No gasket required.
- Much improved scavenging effect due to the both transition and megaphone *Header & Y-Pipe* which mean more power !
- With the benefit of V-Band the swap of those parts can be done in 10 mins ! (either 2x resonator or 2x HFC)

You will need to remove the rear bracing tower shown in the bottom Red square
Edit ; The G37, 350z, G35 has the same setup. Only the 370z has the V-Brace which isn't absolutely needed . The G37 share the exact same setup as the 370z but does not include the V-brace and that big Tower for the brace on the 370z.

then install the provided *blue* rear holding bracket
the 2 holding bolts goes into the already installed welded nut into the frame.
and you will lose the 2 braces going to the front bolts of the sub-frame.
IMO they arent crucial to the rear stability since the 350z does not have it and have the same sub-frame setup.

Ofcourse you will need to remove the rear fog light and slightly cut a circle in it ....

you will have an improved ground clearance since everything was installed to be as close as possible to the frame.

as a bonus half of the exhaust were heat wraped with DEI titanium (100feets of it)

serious buyer only please.

Sorry I do not have a VQ37VHR (VVEL) dyno. since I have the HR heads.
IMO this is the best ALL-OUT exhaust setup on the 370z.

If the following parts are installed
- Stillen Gen 3 CAI
- VHR intake manifold (with intake runner smoothed out)
- my custom Throttle body
- Uprev / EcuTek

I predict it will outperform the Z1 setup that had a result of 342whp with one of our 370z member on their dynojet.

My guess is by over 10whp from what I already gained previously from stock to fully modded
256whp to 324whp = 68whp of gain with my previous less optimized exhaust & HR intake manifold
*WITHOUT VVEL TUNING*

when Z1 only got a gain from stock to fully modded including their secret mod to 62whp of gain and Mike the owner of that Z did said they tuned the VVEL ( from 280 to 342 )

Why am I selling ?
Going another route. and no im not selling the Z

Christmas's special price of 3000$

the kit is evaluated at 5000$ with my welding labour and initial installation on my part.

Megan370z · 12-01-2013, 11:25 AM

Youtube video of the sweet noise

Inside of the car.
with some 1500-7500rpm pull
cruising speed
and last a 4or 5th gear pull ( cant remember )

Video taken outside of the car by the road and doing a fly-by.

Loud and made for a true hardcore enthusiasm driver and/or racer.

most pictures of the exhaust built can be seen here ( click me )

fairlady_z34 · 12-01-2013, 11:46 AM

i think at that price, you should have gotten some dyno results with just exhaust if you wanted some potential buyer. to baller for me. glws

Megan370z · 12-01-2013, 11:52 AM

Quote:

Originally Posted by fairlady_z34

i think at that price, you should have gotten some dyno results with just exhaust if you wanted some potential buyer. to baller for me. glws

can you drive over here with your 370z ? I will be glad to install it and go on the dyno...

as I mentioned in the first post . I dont have the VVEL setup anymore which mean doing a dyno with the HR head is irrelevant.

This new custom exhaust has actually a much better flow potential improvement over my previous one.

DEpointfive0 · 12-01-2013, 12:03 PM

How did you modify the headers?

Megan370z · 12-01-2013, 12:07 PM

Quote:

Originally Posted by DEpointfive0

How did you modify the headers?

Adding a transition and down tube since the throat area was a few tenth thousand under 2 1/4''ID
this help with the scavenging effect of the collector.

fairlady_z34 · 12-01-2013, 12:13 PM

Quote:

Originally Posted by Megan370z

can you drive over here with your 370z ? I will be glad to install it and go on the dyno...

as I mentioned in the first post . I dont have the VVEL setup anymore which mean doing a dyno with the HR head is irrelevant.

This new custom exhaust has actually a much better flow potential improvement over my previous one.

if you were local, i wouldnt mind at all. too bad you are in canada

DEpointfive0 · 12-01-2013, 12:19 PM

Quote:

Originally Posted by fairlady_z34

if you were local, i wouldnt mind at all. too bad you are in Canadia

Fixed

And thanks for the clarification! I have run through your build of it, but I'm sorry, I did not really look into it that much

Vnismo370z · 12-01-2013, 05:13 PM

AWESOME! Love the concept! and with V-bands one could change out the HFCs to straight pipes or resonators... GLWS!

TerribleONE · 12-01-2013, 06:14 PM

Sounds great man. Not a bad deal w the headers IMO

Megan370z · 12-02-2013, 04:30 PM

Make yourself a favor by buying this setup if are seeking the most N/A power possible.

preferably for a race/track car setup ...

Megan370z · 12-02-2013, 05:52 PM

Guess what...

Every N/A parts required to gain atleast a minimun of 70+ whp over stock is now for sale. *WITHOUT VVEL TUNING*
Remember I gained 68whp with a less effective exhaust that was made to fit into the decibel limit rules.

This custom 3.5'' exhaust is way more effective than my previous one.

It will be best to be sold as a kit since everything must match together to avoid bottle neck flow problems.

this include every parts that can be seen in this exhaust thread ( CLICK ME )

this package deal add the following parts ;

- Custom CAI which include a bigger Maf Tube
- Custom Throttle body
- NST Light weight pulley kit ( crank & alternator )
- Base Uprev ROM for this setup ( THIS IS NOT A LICENSE).
I just need your ECU part number and the tuned base ROM will be sent to you with the back to stock ROM. *This alone save your $$ on tuning time...*

this package deal price is set at ; 4750$

Megan370z · 12-04-2013, 04:08 PM

Bump for an Unique Exhaust setup !

Don't forget about the great Full N/A Package 70+whp from stock to fully modded not even VVEL Tuned !

G37sHKS · 12-06-2013, 07:13 PM

Free bump for a very nice setup. Made me wish I had a Z

GLWS bro

Megan370z · 12-08-2013, 06:16 PM

Give yourself a nice Packet Deal for Christmas !

12-01-2013, 10:27 AM	#1 (permalink)
Megan370z A True Z Fanatic Join Date: Oct 2009 Location: Canada Posts: 1,156 Drives: 370z Rep Power: 24	Complete Custom 3.5'' Exhaust Updated info about the complete N/A Package Deal on post # 12 I'm wondering if anybody could be seriously interested into my custom exhaust. the kit include the whole exhaust setup which is; - Modified Momentum headers (not the z1 copy) - Custom Y-Pipe 2.5'' paired with a transition & megaphone to 3.5'' single exit. - Custom 3.5'' mid pipe with a 18'' resonator. - Custom Muffler section 3.5'' in & out. - 2x HFC (y-pipe) - 2x Resonator (y-pipe) - Custom rear holding bracket (with bolts) - All mandrel bent 304SS tubing. - TIG Welded and Back-Purged for improved stronger welds. - Equipped with modified V-bands to reduce turbulence. - No gasket required. - Much improved scavenging effect due to the both transition and megaphone Header & Y-Pipe which mean more power ! - With the benefit of V-Band the swap of those parts can be done in 10 mins ! (either 2x resonator or 2x HFC) You will need to remove the rear bracing tower shown in the bottom Red square Edit ; The G37, 350z, G35 has the same setup. Only the 370z has the V-Brace which isn't absolutely needed . The G37 share the exact same setup as the 370z but does not include the V-brace and that big Tower for the brace on the 370z. then install the provided blue rear holding bracket the 2 holding bolts goes into the already installed welded nut into the frame. and you will lose the 2 braces going to the front bolts of the sub-frame. IMO they arent crucial to the rear stability since the 350z does not have it and have the same sub-frame setup. Ofcourse you will need to remove the rear fog light and slightly cut a circle in it .... you will have an improved ground clearance since everything was installed to be as close as possible to the frame. as a bonus half of the exhaust were heat wraped with DEI titanium (100feets of it) serious buyer only please. Sorry I do not have a VQ37VHR (VVEL) dyno. since I have the HR heads. IMO this is the best ALL-OUT exhaust setup on the 370z. If the following parts are installed - Stillen Gen 3 CAI - VHR intake manifold (with intake runner smoothed out) - my custom Throttle body - Uprev / EcuTek I predict it will outperform the Z1 setup that had a result of 342whp with one of our 370z member on their dynojet. My guess is by over 10whp from what I already gained previously from stock to fully modded 256whp to 324whp = 68whp of gain with my previous less optimized exhaust & HR intake manifold WITHOUT VVEL TUNING when Z1 only got a gain from stock to fully modded including their secret mod to 62whp of gain and Mike the owner of that Z did said they tuned the VVEL ( from 280 to 342 ) Why am I selling ? Going another route. and no im not selling the Z Christmas's special price of 3000$ the kit is evaluated at 5000$ with my welding labour and initial installation on my part. DarkJak and MyKindaGuise like this. __________________ Megan Journal Click Me ....................One Man Team Motorsport Click Me Last edited by Megan370z; 01-11-2014 at 05:10 PM.

12-01-2013, 11:25 AM	#2 (permalink)
Megan370z A True Z Fanatic Join Date: Oct 2009 Location: Canada Posts: 1,156 Drives: 370z Rep Power: 24	Youtube video of the sweet noise Inside of the car. with some 1500-7500rpm pull cruising speed and last a 4or 5th gear pull ( cant remember ) Video taken outside of the car by the road and doing a fly-by. Loud and made for a true hardcore enthusiasm driver and/or racer. most pictures of the exhaust built can be seen here ( click me ) __________________ Megan Journal Click Me ....................One Man Team Motorsport Click Me Last edited by Megan370z; 12-01-2013 at 12:02 PM.

12-01-2013, 12:03 PM	#5 (permalink)
DEpointfive0 Premium Member Bitches Join Date: Jan 2012 Location: SoCal Posts: 14,824 Drives: a lot Rep Power: 17151	How did you modify the headers? __________________ Do YOU want to know what/where I got my username from? ( Click to show/hide ) NSFW due to language:

12-01-2013, 05:13 PM	#9 (permalink)
Vnismo370z Enthusiast Member Join Date: Nov 2011 Location: Tacoma, Wa Posts: 387 Drives: '15 370z PG Sport Rep Power: 13	AWESOME! Love the concept! and with V-bands one could change out the HFCs to straight pipes or resonators... GLWS! __________________ starting over

12-01-2013, 06:14 PM	#10 (permalink)
TerribleONE A True Z Fanatic Join Date: Jan 2009 Location: Socal Posts: 10,203 Drives: WOT Rep Power: 5850	Sounds great man. Not a bad deal w the headers IMO __________________ 638WHP 541WTQ @ 13.5PSI Build thread

12-01-2013, 11:46 AM	#3 (permalink)
fairlady_z34 Track Member Join Date: May 2013 Location: socal Posts: 568 Drives: 09 370z touring Rep Power: 13	i think at that price, you should have gotten some dyno results with just exhaust if you wanted some potential buyer. to baller for me. glws

12-02-2013, 04:30 PM	#11 (permalink)
Megan370z A True Z Fanatic Join Date: Oct 2009 Location: Canada Posts: 1,156 Drives: 370z Rep Power: 24	Make yourself a favor by buying this setup if are seeking the most N/A power possible. preferably for a race/track car setup ... __________________ Megan Journal Click Me ....................One Man Team Motorsport Click Me

12-02-2013, 05:52 PM	#12 (permalink)
Megan370z A True Z Fanatic Join Date: Oct 2009 Location: Canada Posts: 1,156 Drives: 370z Rep Power: 24	Guess what... Every N/A parts required to gain atleast a minimun of 70+ whp over stock is now for sale. WITHOUT VVEL TUNING Remember I gained 68whp with a less effective exhaust that was made to fit into the decibel limit rules. This custom 3.5'' exhaust is way more effective than my previous one. It will be best to be sold as a kit since everything must match together to avoid bottle neck flow problems. this include every parts that can be seen in this exhaust thread ( CLICK ME ) this package deal add the following parts ; - Custom CAI which include a bigger Maf Tube - Custom Throttle body - NST Light weight pulley kit ( crank & alternator ) - Base Uprev ROM for this setup ( THIS IS NOT A LICENSE). I just need your ECU part number and the tuned base ROM will be sent to you with the back to stock ROM. *This alone save your $$ on tuning time...* this package deal price is set at ; 4750$ __________________ Megan Journal Click Me ....................One Man Team Motorsport Click Me Last edited by Megan370z; 12-02-2013 at 06:56 PM.

12-04-2013, 04:08 PM	#13 (permalink)
Megan370z A True Z Fanatic Join Date: Oct 2009 Location: Canada Posts: 1,156 Drives: 370z Rep Power: 24	Bump for an Unique Exhaust setup ! Don't forget about the great Full N/A Package 70+whp from stock to fully modded not even VVEL Tuned ! __________________ Megan Journal Click Me ....................One Man Team Motorsport Click Me Last edited by Megan370z; 12-04-2013 at 05:28 PM.

12-06-2013, 07:13 PM	#14 (permalink)
G37sHKS A True Z Fanatic Join Date: Feb 2010 Location: Dubai Posts: 1,183 Drives: 09 G37S Coupe 7AT Rep Power: 20	Free bump for a very nice setup. Made me wish I had a Z GLWS bro Megan370z likes this. __________________ G37 BUILD UNDER CONSTRUCTION

12-08-2013, 06:16 PM	#15 (permalink)
Megan370z A True Z Fanatic Join Date: Oct 2009 Location: Canada Posts: 1,156 Drives: 370z Rep Power: 24	Give yourself a nice Packet Deal for Christmas ! __________________ Megan Journal Click Me ....................One Man Team Motorsport Click Me

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Complete Audio Setup w/ Custom Box	bchinfoon	Audio & Video	12	07-08-2013 09:58 PM
[FOR SALE] Complete Custom Audio Setup	Harvin370z	Parts for sale (Private Classifieds)	8	11-07-2012 12:58 AM
Custom Single Side: Complete!	TypeOne	Intake/Exhaust	74	06-04-2012 03:16 PM