Stripped Screw on Door Handle

Econ · 05-05-2011, 10:47 AM

Ok, so i was removing my door handles to paint them. The driver side came off no problem, however the passenger side door was a different story. The screw holding the plate that holds the lock in place was completely stipped.

It would be impossible to take this out with a screw driver. Any ideas how to remove this screw?

Thanks in Advance

Trips · 05-05-2011, 11:02 AM

Small needle nose vise-grips

Econ · 05-05-2011, 11:08 AM

Quote:

Originally Posted by Triple's

Small needle nose vise-grips

not a bad idea actually. Hopefully the screw isnt too low profile.

thanks for the quick response

shadoquad · 05-05-2011, 11:12 AM

Another option could be a screw removal kit.

However, if they put too much sticky chemical on the screw, it might not come out.

When I replaced my accelerator pedal, the bolts were in so tight that I sheared the heads off of them and they were recessed. Then with a proper screw removal kit and drill, they were stuck in so bad that the bits broke in the removal process.

I eventually had AAM look at it. They left those bolts as they were and drilled new holes and ordered new bolts to keep my accelerator down.

Nightmare. 150 dollar pedals cost me 600 bux.

But you might want to look at a screw removal kit or ask a garage (with a machining shop) to take a look at it.

alb84z31t · 05-05-2011, 11:15 AM

Quote:

Originally Posted by shadoquad

Another option could be a screw removal kit.

However, if they put too much sticky chemical on the screw, it might not come out.

When I replaced my accelerator pedal, the bolts were in so tight that I sheared the heads off of them and they were recessed. Then with a proper screw removal kit and drill, they were stuck in so bad that the bits broke in the removal process.

I eventually had AAM look at it. They left those bolts as they were and drilled new holes and ordered new bolts to keep my accelerator down.

Nightmare. 150 dollar pedals cost me 600 bux.

But you might want to look at a screw removal kit or ask a garage (with a machining shop) to take a look at it.

If there is a lot of Loc-tite on them, you may want to try heating it up with a torch also. I have to use that trick quite a bit on my bike.

Econ · 05-05-2011, 11:41 AM

Quote:

Originally Posted by alb84z31t

If there is a lot of Loc-tite on them, you may want to try heating it up with a torch also. I have to use that trick quite a bit on my bike.

i would be to worried about melting the elecric door sensor right under the screw

Davey · 05-05-2011, 12:50 PM

Quote:

Originally Posted by Econ

i would be to worried about melting the elecric door sensor right under the screw

Not sure how close we're talking but you could try a soldering gun.

kenchan · 05-05-2011, 03:55 PM

go to your hardware store and look for easy outs. sears hardware has them for sure cause i have a few sets.

you drill a hole into the stripped screw head. then you put the easy-out in there..bascially a drill bit with a reverse direction blade. screws out.

05-05-2011, 10:47 AM	#1 (permalink)
Econ A True Z Fanatic Join Date: Jan 2011 Location: New York City Posts: 2,546 Drives: Fiat? Rep Power: 19	Stripped Screw on Door Handle Ok, so i was removing my door handles to paint them. The driver side came off no problem, however the passenger side door was a different story. The screw holding the plate that holds the lock in place was completely stipped. It would be impossible to take this out with a screw driver. Any ideas how to remove this screw? Thanks in Advance

05-05-2011, 11:02 AM	#2 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,732 Drives: 🔰 Rep Power: 10	Small needle nose vise-grips __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY-Door handle removal	bumblez	DIY Section (Do-It-Yourself)	104	09-29-2017 08:00 PM
Door handle rattles from outside...anyone?	zaust	Exterior & Interior	1	02-27-2012 04:21 PM
370z door handle swap?	ThoriumHotdog	Exterior & Interior	11	11-03-2010 11:44 PM
tried to remove door handle...Fail	Soon	DIY Section (Do-It-Yourself)	4	08-02-2010 05:03 PM
Door handle sticking/not opening	abakja1	Exterior & Interior	7	11-10-2009 03:11 AM

05-05-2011, 11:12 AM	#4 (permalink)
shadoquad A True Z Fanatic Join Date: Apr 2010 Location: . Posts: 42,608 Drives: . Rep Power: 3886	Another option could be a screw removal kit. However, if they put too much sticky chemical on the screw, it might not come out. When I replaced my accelerator pedal, the bolts were in so tight that I sheared the heads off of them and they were recessed. Then with a proper screw removal kit and drill, they were stuck in so bad that the bits broke in the removal process. I eventually had AAM look at it. They left those bolts as they were and drilled new holes and ordered new bolts to keep my accelerator down. Nightmare. 150 dollar pedals cost me 600 bux. But you might want to look at a screw removal kit or ask a garage (with a machining shop) to take a look at it.

05-05-2011, 03:55 PM	#8 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	go to your hardware store and look for easy outs. sears hardware has them for sure cause i have a few sets. you drill a hole into the stripped screw head. then you put the easy-out in there..bascially a drill bit with a reverse direction blade. screws out.