2009 base won't start

BroJake · 06-28-2017, 06:40 PM

Hey all,
Like the title says my 2009 Z won't start.
Last week I was leaving the house and got about 200 meters down the road and the car just shut off. No stalling no sputtering just like I had clicked it off.
I pull over try to start it, and the starter works fine. The engine cranks fires once and then dies.
MIL is on at this point.
I checked oil levels all good there.
Get it pushed back to the house and plugged into an OBD scanner to find P0340 code stored.
This prompted me to buy camshaft position sensors and crankshaft position sensor.
This didn't fix the problem car still showing same symptoms.
I read on here someone had gotten Zs to start with this code by removing one Cam sensor and starting it in limp mode. So to somewhat rule out complete mechanical failure I tried this.
Car starts right up in limp mode with either or cam sensor unplugged.
I drove it to the dealership in limp mode. During this time it seemed to drive perfectly fine.
The mechanic at the dealership claims the vehicle had a stored P0011 code and that the cam sprocket is retarded -17 degrees.
So I've bought all the necessary timing parts and I'm getting ready to tackle that but I'm not entirely convinced that's the issue. If this was a timing issue wouldn't the vehicle run terribly?
Any information would be most appreciated.
Thanks all
Jake

BroJake · 07-19-2017, 11:16 AM

Quick update on this. (If anyone wants one haha)
The issue here was indeed the Timing Chain. or rather a tensioner on driver's side of engine that gave out. Causing the slip in timing.
There doesn't seem to be a decent DIY (that I could find) on this so I've documented everything we've done thus far and will finish the work this weekend.
Hopefully get the DIY written and submitted next week!
This job has been a right pain in the @$$ in terms of how time consuming this has been.
Plus I had trouble finding parts which further delayed me.

SouthArk370Z · 07-19-2017, 11:30 AM

Congratulations on figuring it out. Looking forward to seeing the DIY.

stopher · 07-24-2017, 02:47 PM

How many miles on the car? Is it around 100k? Seems like an issue with GT-R as well.

djones 1954 · 07-27-2017, 08:39 PM

I have similar issue with a 2013 370z 24000 miles on it. Died at an intersection. It threw a P0340 code. I changed both cam sensors and crank sensor Still did not start. Unplugged right side sensor and it starts in limp mode. Dealer checked it and reports that "cam sensor isn't getting correct electrical signal, has electrical problems." I take it home and pull ECM. Power wire (green) to sensor has 5.4V and no short circuits. Ground (pink) OHM's good and signal wire (orange) has good continuity from sensor to ECM no shorts and disconnected from ECM.
This Z is box stock with no mods, wife's car, she likes it because its cute.
Do I check for cam timing issues from this point?

06-28-2017, 06:40 PM	#1 (permalink)
BroJake Base Member Join Date: Feb 2017 Location: Dallas, TX Posts: 9 Drives: 2009 370Z Rep Power: 8	2009 base won't start Hey all, Like the title says my 2009 Z won't start. Last week I was leaving the house and got about 200 meters down the road and the car just shut off. No stalling no sputtering just like I had clicked it off. I pull over try to start it, and the starter works fine. The engine cranks fires once and then dies. MIL is on at this point. I checked oil levels all good there. Get it pushed back to the house and plugged into an OBD scanner to find P0340 code stored. This prompted me to buy camshaft position sensors and crankshaft position sensor. This didn't fix the problem car still showing same symptoms. I read on here someone had gotten Zs to start with this code by removing one Cam sensor and starting it in limp mode. So to somewhat rule out complete mechanical failure I tried this. Car starts right up in limp mode with either or cam sensor unplugged. I drove it to the dealership in limp mode. During this time it seemed to drive perfectly fine. The mechanic at the dealership claims the vehicle had a stored P0011 code and that the cam sprocket is retarded -17 degrees. So I've bought all the necessary timing parts and I'm getting ready to tackle that but I'm not entirely convinced that's the issue. If this was a timing issue wouldn't the vehicle run terribly? Any information would be most appreciated. Thanks all Jake Last edited by BroJake; 06-28-2017 at 08:27 PM.

07-19-2017, 11:30 AM	#3 (permalink)
SouthArk370Z Premium Member Join Date: Nov 2010 Location: South Arkansas Posts: 8,435 Drives: 2014 Challenger Rep Power: 324198	Congratulations on figuring it out. Looking forward to seeing the DIY. __________________ Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ATTENTION!! 2009-2010 owners with steering lock/wont start issues	Trips	Nissan 370Z General Discussions	510	01-02-2022 07:21 AM
370Z For Sale Base 2009 6MT $14,900	BuegeCJ	370Z For Sale	2	09-02-2016 01:40 PM
[FOR SALE] stock base headunit + speakers + start button	ufoz8mycow	Parts for sale (Private Classifieds)	6	10-15-2014 02:27 PM
[FOR SALE] 2009 370z stock start button. $25.00.	mgadrix	Parts for sale (Private Classifieds)	1	08-26-2013 05:23 PM
[FOR SALE] 2009 370z stock start button. $25.00.	mgadrix	Parts for sale (Private Classifieds)	0	08-25-2013 10:26 AM

07-19-2017, 11:16 AM	#2 (permalink)
BroJake Base Member Join Date: Feb 2017 Location: Dallas, TX Posts: 9 Drives: 2009 370Z Rep Power: 8	Quick update on this. (If anyone wants one haha) The issue here was indeed the Timing Chain. or rather a tensioner on driver's side of engine that gave out. Causing the slip in timing. There doesn't seem to be a decent DIY (that I could find) on this so I've documented everything we've done thus far and will finish the work this weekend. Hopefully get the DIY written and submitted next week! This job has been a right pain in the @$$ in terms of how time consuming this has been. Plus I had trouble finding parts which further delayed me.

07-24-2017, 02:47 PM	#4 (permalink)
stopher Base Member Join Date: Mar 2012 Location: San Jose, CA Posts: 107 Drives: 2013 Nissan GT-R Rep Power: 13	How many miles on the car? Is it around 100k? Seems like an issue with GT-R as well.

07-27-2017, 08:39 PM	#5 (permalink)
djones 1954 Base Member Join Date: Jul 2017 Location: texas Posts: 1 Drives: 1982 z28 Rep Power: 8	I have similar issue with a 2013 370z 24000 miles on it. Died at an intersection. It threw a P0340 code. I changed both cam sensors and crank sensor Still did not start. Unplugged right side sensor and it starts in limp mode. Dealer checked it and reports that "cam sensor isn't getting correct electrical signal, has electrical problems." I take it home and pull ECM. Power wire (green) to sensor has 5.4V and no short circuits. Ground (pink) OHM's good and signal wire (orange) has good continuity from sensor to ECM no shorts and disconnected from ECM. This Z is box stock with no mods, wife's car, she likes it because its cute. Do I check for cam timing issues from this point?