Z shows up to the Mustang Dyno Day!

Nismodean

Yep you read that right! I drive up to The Mustang Shop in Auburn, Wa. and boy did I get some looks! I didn't care though as it was 3 pulls for $65 I was gonna get mine! In all honesty the guys that work there are polite and answered all the questions I had as this was the first time I've ever done a dyno pull let alone see one in person.

First off I am completely amazed by this car. It's rated at 332 horsepower and this little gem of mine was pulling 316 SAE corrected HP to the wheels! Just after the 2nd pull the guys were doing some figures and for a 15% loss the engine would have to be outputting about 370 at the flywheel to get the numbers I was getting. I'm still at a loss as to how I got such good numbers as this car is bone STOCK!

Well here is the video, it's not edited so I apologize for the length (9 minutes).

TreeSemdyZee

Not to be a downer, but Mustang dynos are known to read high. If you run on a Dynojet, the numbers will be lower.

m4a1mustang

Hey, I'm showing up to ZDayZ in a Mustang... it's all good.

Though 316 to the wheels definitely is an inflated figure. In general a bone stock 370 puts down 275-285 to the wheels on a DynoJet.

__________________
- Steve

Zs & Coffee - Saturdays at 10AM in Fairfax, VA and Columbia, MD (Click the banner!)
LIKE us on Facebook!

Nismodean

That is good to know, so the question is, is a Dynojet more accurate or just reads lower?

Jordo!

Accuracy is relative in absolute terms -- any dynomometer can give you repeatable results.

If you mean the "true" power, then unbolt the motor. On a chassis dyno, it is always an estimate.

If you want to get estimates that will be incredibly stable from shop to shop, the dynojet (interia dyno) is king. HP and tq figures are calculated based on how quickly the wheels can accelerate the known constant weight of the drum.

For eddy current (load bearing) dynos, there are lots of "fudge factors", so readings will tend to be more variable from shop to shop.

Personally, I prefer dynojets simply beause the results from different shops are more easily compared. If a guy at x shop in CA put down 296 on a dynojet with such and such mods, odds are he'd put down right about 296 on a dynojet at y shop in PA. Not so with a Mustang dyno.

__________________
Enjoy it. Destroy it.

Nismodean

Ok, so this is my findings. I spent this whole time researching DJ vs Mustang dynos and EVERY source but this one says that Dynojets read higher than Mustang dynos. Granted Dynojets are the current standard mainly due to the fact that there are more Dynojets out there than Mustang dynos. I also came across this interesting post, take a read and lemme know what you guys think:

DynoJets are inertia dynos, and have been around for years, much longer than any type of load cell dyno. Inertia dyno's work on the principle of the acceleration of a known mass over time. Their rollers are the known mass. Weighing in at over 2500lbs or so. Your car gets strapped down to the machine, and the dyno collects it's data. It is able to calculate horsepower by measuring the acceleration in rpm of the rollers in regards to RPM. This is why gearing can affect the dyno results, more on that in a bit. Now that the dyno has recorded the horsepower curve, it can take the integral of that curve and get the torque curve. Since the dyno’s power calculations are based on the acceleration of mass over time in regards to RPM, gearing is very important. Since a vehicle with a lower gear ratio can accelerate the mass to a higher speed using less engine RPM, it will show a higher horsepower number than a car with a higher gear ratio. If a car is able to accelerate the dyno’s rollers from 200rpm (roller) to 300rpm (roller)in 1500rpm (engine), then the dyno is going to record more power than a car that did that in 2000rpm (engine).

Now we go to Mustang dyno’s and other loaded dyno’s. Our Mustang MD-1100SE dyno’s rollers weigh 2560lbs. That is the actual mass of the rollers, much like the DynoJet. That’s about where all the similarities end. When we get a car on our dyno, we enter two constants for the dyno’s algorithms. One being the vehicle weight, the other being what’s called “Horsepower At 50mph”. This is a number that represents how much horsepower it takes for the vehicle to push the air to maintain 50mph. This is used as the aerodynamic force. Mustang dyno’s are also equipped with a eddy currant load cell. Think of a magnetic brake from a freight train. This magnetic brake can apply enough resistance to stall a big rig. Off one side of the eddy currant load cell, there is a cantilever with a 5volt reference load sensor (strain gage). As the rollers are spinning this load sensor is measuring the actual torque being applied. So as the rollers spin, the load sensor is measuring the force being applied, sending that information to the dyno computer, taking into account the two constants entered earlier, computing the amount of resistance needed to be applied to the rollers to load the car so that the force of the rollers resistance is as close to the force the car sees on the street. The dyno is then able to calculate the total force being applied to the rollers in torque, and then taking the derivative of that torque curve to arrive at the horsepower curve. Since torque is an actual force of nature, like gravity and electricity, it can be directly measured. Horsepower is an idea that was thought up by man, and cannot be directly measured, only calculated.

I like to state it like this. . . I start by asking how much your car weighs, lets say 3500lbs. Now you take your car and you make a make a WOT rip in your tallest non overdrive gear, how much mass is your engine working against? 3500lbs right? Now you strap your car on a DynoJet and you make a WOT in the same gear, how much mass is your engine working against? 2500lbs right? Now you strap your car on a Mustang dyno, how much mass is your engine working against? 2500lbs. Plus the resistance being applied by the eddy current generator. We’ve seen anywhere for 470lbs of resistance to over 700lbs of resistance as measured in PAU force in the data logs. So which one is more accurate? Well they their both accurate. If a DynoJet dyno says you made 460rwhp, then you made 460rwhp. If a Mustang dyno says you made 460rwhp, you also made 460rwhp. Now which one of those numbers best represents what your car is doing when its on the street. That’s a different question.

The most important thing to remember is that a dyno is a testing tool. If the numbers keep increasing, then you’re doing the right thing. We try to look over at NET gain, instead of Peak HP numbers. A 30rwhp increase is a 30rwhp increase regardless of what dyno it is on.

Now I can address how to calculate the difference between one type of dyno and another. Simply put, you can’t. Because Mustang dyno’s have so many more variables, it’s not a simple percentage difference. We’ve had cars that made 422rwhp on our Dyno, two days later make 458rwhp on a DynoJet the next day. We’ve also had cars that made 550rwhp on our dyno, make 650+rwhp on a DynoJet a few days later at another shops Dyno Day. For instance, my 2002 Z28 with a forged internal LS6 Heads/Cam/Intake, makes 460rwhp on our dyno. I thought that was a little low, since I’ve had cam only LS6 Z06 vettes make 450rwhp. So I overlaid the dyno graphs. Guess what, the PAU force for my car was almost 200lbs more than the C5Z06 that made 450rwhp with cam only. So I entered the weight and horsepower at 50 number for a C5Z06 and did another horsepower rip with my car. The only reason I did that was to compare Apples to Apples. This time my car made 490rwhp, no other changes. Now I don’t go around saying my car made 490rwhp, I say what it actually did with the correct information entered into the computer. It made 460rwhp. Now if I ever get a chance to take it on a DynoJet (which I plan to in the spring), I have no doubts it’ll be over 500rwhp. I know this based on airflow and fuel consumption on the data logs.

But since we’re asked this question constantly we're fairly conservative, and hence tell our customers that the difference is closer to 6-7%, but as you make more power, and the more your car weighs, the difference increases as well. You must remember, Dyno's regardless of the type are tuning tools, and are in no means meant to tell people how fast their car is. Now which one is more "real world" is a totally different question. I like to explain it like this..... If you drive your car in a situation in which you have no mass and you're in a vacuum, so basically if you do intergalactic racing in space, use a DynoJet. If your car sees gravity, and has an aerodynamic coefficient, and you race on a planet called Earth, then use a Mustang Dyno

daisuke149

what gear did you dyno in?

Nismodean

5th gear

docaam

mine with full bolt ons gave me 241 before tune and 261 after the tune on a mustang dyno. I heard mustang is a better dyno for tunning

__________________
Old 370Z SOLD but not forgotten
370Z 40th, G37s, S30 RBZ, Hakosuka Skyline

Jordo!

Dude... just go do a few pulls on a dynojet and lo and behold your car will magically make between 270 and 280 whp.

Mustang dynos can break hearts or they can lift spirits -- it all depends on the settings.

That shop clearly had it set in such a way that you got a wild overestimate of your whp... either that or Nissan accidentially put a V8 under the hood.

If you want numbers you can compare with other people who dyno at different shops (on dynojets) go find a dynojet.

__________________
Enjoy it. Destroy it.

geosZ

Dynojet my car last week 289 7at
And my boy got 297 with a pully 7at

Was a good day

__________________
ark cbe R.I.P.°berk test pipes°red injen cai°180 lights°eibach springs°spacers°pioneer navi/dvd°stillen splitter°carbonsignal fenders°xxr 527 wheels•momo Italy floor mats•weapon R 4 point Raceing harness. SOLD. NEW CAR 2012 Subaru Sti sedan ice silver.

Jordo!

STD or SAE correction? Mods (other than the pulley)?

__________________
Enjoy it. Destroy it.

geosZ

Auto 4th gear pull no other mods only stillen pully

__________________
ark cbe R.I.P.°berk test pipes°red injen cai°180 lights°eibach springs°spacers°pioneer navi/dvd°stillen splitter°carbonsignal fenders°xxr 527 wheels•momo Italy floor mats•weapon R 4 point Raceing harness. SOLD. NEW CAR 2012 Subaru Sti sedan ice silver.

Footloose301

I did 378whp with just an intake on the butt dyno. Maybe it's readings are off.

__________________

2010 40th Anniversary 370Z

Osiris

just to clarify here, dynojets read HIGHER than mustang dynos.

__________________

^^^^^^^^^Like our Facebook!^^^^^^^^^