rhino ramps

soxfan69 · 03-12-2014, 08:23 PM

Jaedub. The ramps work fine. I just wanted to make those who haven't used them to be aware. Oil change was simple. You just go in from the frnt, remove 4 10mm bolts and the filter and oil plug Is right there. As for the exhaust, I will Jack up the rear and place on jackstands. Be sure to wheel chock the front since there is no roll back lip on the ramps.
Happy Wrenching

synolimit · 03-12-2014, 09:03 PM

Quote:

Originally Posted by soxfan69

As for the exhaust, I will Jack up the rear and place on jackstands.

i drive up backwards on the ramps when i need to do rear work.

mab864 · 03-13-2014, 08:50 AM

I tried rhino ramps but they slipped on my smooth garage floor. I didn't want to mess with blocks so I invested in 4 esco jack stands. They are awesome! I lift at the front lift point (with a hockey puck) and put my jack stands both in on that side. Then do the other side. It works for me and it's fast. To just lift the rear I lift from the differential and put in two jack stands (and block the front wheels).

kenchan · 03-13-2014, 11:06 AM

if only i didnt have the damn raised area in my garage i could do this without moving my car...

can't get my hydaulic under the front.

but since i have to move my car anyway, i just use ramps as it's quicker and safer for me.

03-13-2014, 08:50 AM	#18 (permalink)
mab864 Enthusiast Member Join Date: Nov 2013 Location: Oregon Posts: 482 Drives: 13 Sport 6MT Rep Power: 12	I tried rhino ramps but they slipped on my smooth garage floor. I didn't want to mess with blocks so I invested in 4 esco jack stands. They are awesome! I lift at the front lift point (with a hockey puck) and put my jack stands both in on that side. Then do the other side. It works for me and it's fast. To just lift the rear I lift from the differential and put in two jack stands (and block the front wheels). __________________ Berk HFC & CBE, Stillen G3, UpRev & tune by PSI, GTMat, 3M, Swift, StopTech, H&R 20/25, GT-R, 324 whp & 262 torque

03-13-2014, 11:06 AM	#19 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	if only i didnt have the damn raised area in my garage i could do this without moving my car... can't get my hydaulic under the front. but since i have to move my car anyway, i just use ramps as it's quicker and safer for me. soxfan69 likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Question about Rhino Ramps	Guard Dad	Nissan 370Z General Discussions	55	04-28-2014 11:08 AM
Rhino Ramps & Nismo 370z	luigi90210	Nissan 370Z General Discussions	3	07-17-2013 07:55 PM
Wide loaded rhino ramps , less than 30 bux	cossie1600	DIY Section (Do-It-Yourself)	29	01-17-2012 08:00 AM
Extensions for Rhino Ramps	ggiwin	DIY Section (Do-It-Yourself)	2	12-05-2011 03:02 PM
Need Race Ramps service ramps and trailer ramps? Save hundreds with this combo deal.	Fred@ReverseLogic	Tools / Ramps	1	03-04-2011 08:13 AM

03-12-2014, 08:23 PM	#16 (permalink)
soxfan69 Base Member Join Date: Jan 2014 Location: jax florida Posts: 122 Drives: 2012 370z gunmetal Rep Power: 11	Jaedub. The ramps work fine. I just wanted to make those who haven't used them to be aware. Oil change was simple. You just go in from the frnt, remove 4 10mm bolts and the filter and oil plug Is right there. As for the exhaust, I will Jack up the rear and place on jackstands. Be sure to wheel chock the front since there is no roll back lip on the ramps. Happy Wrenching