Headers, CBE, HFCS

Stoney

I was just thinking about something I want to do, but want to make sure it will work. I currently have a borla CBE and I want to put on Berk HFCs and stillen short tube headers, WILL IT FIT , when they go to install? Because I know the xyz pipe won't fit with berk HFCs. Thanks for the help!!

NismoZ70

So you're still considering the Stillen headers I see

Stoney

Yes, I know it may not be worth it, but any gain is better than no gain, and long tubes are illegal. And I just want a full setup!

Phenix

Why not the z1 headers? Z1 headers will require a 350z HFC but it fits and should give you some power gains

Sent from my XT1060 using Tapatalk

Stoney

Because I'm kind of nervous about putting 350z HFCs on it, and I want either stillen or berk HFCs , since I've heard good things about both and like the way they sound, also the z1s are a little bit out of my price range.

7speed

Everybody told u to leave the stock headers alone, not worth it. U probably get better gain from upgraded intake manifold vs stillen shorty.

__________________
09 370z 6spd traded 1/12/15 for 15 Challenger RT 6spd

Stoney

Yeah we'll don't forget it's what I want to do, not what Everybody else wants me to do!

SmokeEater27

__________________
LLUMAR TINT 15% l ARK GT-S SPRINGS l STILLEN GEN 3 C.A.I l MOMO SHIFTER l Z1 SPACERS 20MM (F)/25MM (R).....STILL LOADING

Phenix

Berk makes 350z cats you could use with Z1 headers

Sent from my XT1060 using Tapatalk

Trips

While I agree with members suggestions that gains are very minimal for the expense of header/labor $$$

I might suggest NST lightweight under drive pulleys as an alternative.

The gains will be in line with a short header swap and less expensive altogether.

__________________

IDZRVIT

Hey, it's your money but consider this. How will changing a factory tuned header to an aftermarket header produce any noticeable gains from an already highly tuned engine? You can only squeeze so much power out from this engine. These engines being highly tuned already don't respond the same as for example, a small block chevy would with similar mods. Money better spent on a good tune vice headers. If you want real power gains, go FI.

__________________
"America.... still builds rockets!"
Vette: 355 cid, 400 rwhp
'13 CTS-V Coupe: 6.2L LSA, 556HP

Chuck33079

Fast intentions will make you a catback with HFCs in it so you can run their long tubes and still be legal. That's a far better hp/$ ratio for the same install cost.

__________________
2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

gbrettin

How about trying a different approach OP. It's not ALL about producing higher HP. Have you considered modifications to save weight? Z1 has a 2 piece rotor set available at a decent price point. NST underdrive pulley is another good option. How about a lightweight battery?

You see where I'm going with this.

SPOHN

No reason to do headers if you don't install them your selves or you have to run HFC's. Your just robbing yourself. Cost of header install and the restrictions of HFC's.

__________________

DEpointfive0

If long tubes are illegal, I'm sure a header swap with HFCs is too... Actually, I know it's illegal...

Stillen and Berk make HFCs for the 350Z too... The ONLY difference is the flange.

Exactly. If you're going to WASTE your $600+ on Stillen headers I dont understand why you don't save an extra few hundred to get better than stock headers...

The best review I've seen on a friend's car was 7hp... Another friend, +2HP... The dyno reads +/- 5hp anyways...

__________________
Do YOU want to know what/where I got my username from?