Nissan 370Z Forum  

Weird clanking noise

okay i fix the problem myself. i rented out a lift and did all the adjusting myself stupid exhaust shop rushed everything so it wasnt set right. only cost me

Go Back   Nissan 370Z Forum > Nissan 370Z General Area > Nissan 370Z General Discussions


Reply
 
LinkBack Thread Tools Display Modes
Old 07-12-2009, 07:08 PM   #16 (permalink)
Enthusiast Member
 
thispecialk's Avatar
 
Join Date: Jul 2009
Location: San Diego, CA
Posts: 483
Drives: 2009 370z, manual,
Rep Power: 16
thispecialk is on a distinguished road
Default

okay i fix the problem myself. i rented out a lift and did all the adjusting myself stupid exhaust shop rushed everything so it wasnt set right. only cost me 3 dollars to rent the lift and tools
thispecialk is offline   Reply With Quote
Old 07-15-2009, 09:52 AM   #17 (permalink)
Enthusiast Member
 
thispecialk's Avatar
 
Join Date: Jul 2009
Location: San Diego, CA
Posts: 483
Drives: 2009 370z, manual,
Rep Power: 16
thispecialk is on a distinguished road
Default

o quick question to anyone is it possible to over tighten the bolt that with a torque gun. i think i might of gotten carried away with using it and paranoid that the bolts wasnt tight enough. should i try and losen these alittle or dont worry about it. im wondering if i crush the metal peice where the exhaust is adjustable in the front near the cat i kept torqing the **** out of it
thispecialk is offline   Reply With Quote
Old 07-15-2009, 11:10 AM   #18 (permalink)
A True Z Fanatic
 
wstar's Avatar
 
Join Date: Mar 2009
Location: Houston, TX
Posts: 4,024
Drives: too slow
Rep Power: 3594
wstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond repute
Default

Yes, you can in theory over-torque an exhaust flange, especially with an air wrench (which what I assume you mean by torque gun). The primary concern would be that you overtorqued one side before the other side was sufficiently torqued, which might warp or bend the flange. Stillen's instructions should have the correct torque values, I don't recall them offhand. In general this stuff should be done by hand (as should all tightening, and then use a torque wrench to get the correct value if necessary. You really only use an air wrench for loosening things in most car applications).

All of that said, unless you went really crazy with the air wrench, you're probably ok. If it's not leaking, just leave the bolts as they are. Loosening and retightening could make things worse if you've already overtorqued (like cause gasket failure). You did use anti-seize compound on the bolt threads right?
__________________
7AT Track Car!
Journal thread / Car setup details
wstar is offline   Reply With Quote
Old 07-15-2009, 11:18 AM   #19 (permalink)
Enthusiast Member
 
thispecialk's Avatar
 
Join Date: Jul 2009
Location: San Diego, CA
Posts: 483
Drives: 2009 370z, manual,
Rep Power: 16
thispecialk is on a distinguished road
Default

no i didnt i dont even know wat that is(anti-seize compound). only thing i use the air wrench on is the 2 bolts in the very front holding the exhaust up. the bolts that u can adjust. im worried now i might of went alittle crazy on the air wrench. heres instruction on which bolt
10. Tighten the bolts and clamps from the
front to the back making sure the
system is straight and clear of the sway bar
and cross member. The front bolt holes at the
catalytic converters allow for some adjustment
for this. The flanges on the mufflers should be
tightened last AFTER checking alignment of
the exhaust tips to the rear valance.

Last edited by thispecialk; 07-15-2009 at 11:24 AM.
thispecialk is offline   Reply With Quote
Old 07-15-2009, 11:28 AM   #20 (permalink)
Enthusiast Member
 
thispecialk's Avatar
 
Join Date: Jul 2009
Location: San Diego, CA
Posts: 483
Drives: 2009 370z, manual,
Rep Power: 16
thispecialk is on a distinguished road
Default

i wonder if im gonna be able to take those nutz off or if it warp the metal. its been 4 days now. i wont be able to barrow a lift till the week end cause thats only time there open
thispecialk is offline   Reply With Quote
Old 07-15-2009, 01:49 PM   #21 (permalink)
A True Z Fanatic
 
wstar's Avatar
 
Join Date: Mar 2009
Location: Houston, TX
Posts: 4,024
Drives: too slow
Rep Power: 3594
wstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond repute
Default

Anti-seize compound is available at any auto parts store. If you don't use it, eventually (many miles later) the exhaust bolts will pretty much weld/rust themselves into place and will be very difficult or impossible to remove without cutting them.

Also, the gaskets burn in to some degree, getting thinner and sticking to the flange metal as they get heated by the exhaust. In my experience, the type of gaskets the aftermarket companies are using (Berk, Stillen) can't really be re-used once they've burned in. By that I mean, if you go and loosen those flanges again, the gasket may not reseal when you tighten it back down, so you need to have a new set of gaskets on hand if you do that.
__________________
7AT Track Car!
Journal thread / Car setup details
wstar is offline   Reply With Quote
Old 07-15-2009, 10:12 PM   #22 (permalink)
Enthusiast Member
 
thispecialk's Avatar
 
Join Date: Jul 2009
Location: San Diego, CA
Posts: 483
Drives: 2009 370z, manual,
Rep Power: 16
thispecialk is on a distinguished road
Default

Well like said only thing I'm worried about is the front bolts holding the exhaust up cause of the air wrench.

Last edited by thispecialk; 07-21-2009 at 01:13 AM.
thispecialk is offline   Reply With Quote
Old 07-21-2009, 01:15 AM   #23 (permalink)
Enthusiast Member
 
thispecialk's Avatar
 
Join Date: Jul 2009
Location: San Diego, CA
Posts: 483
Drives: 2009 370z, manual,
Rep Power: 16
thispecialk is on a distinguished road
Default

how will i know if my sway bar is hitting my exhaust? i look under neat and theres about half an inch space in between them. will they hit each other if i hit a bump or pot hole? i move the exhaust up more so the exhaust dont hit the crossmember but now im worried about the sway bar
thispecialk is offline   Reply With Quote
Old 08-22-2009, 12:01 AM   #24 (permalink)
Enthusiast Member
 
thispecialk's Avatar
 
Join Date: Jul 2009
Location: San Diego, CA
Posts: 483
Drives: 2009 370z, manual,
Rep Power: 16
thispecialk is on a distinguished road
Default

Has anyone wrap the crossmember with heat shield to stop the clanking
thispecialk is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
*NSFW* - Funny/Weird/Gross pics&vids xDIEGOx The Lounge (Off Topic) 7325 11-01-2014 08:33 PM
Super Weird Bugs BanningZ The Lounge (Off Topic) 87 10-26-2009 12:25 AM
weird 6th gear problem corbin09 Engine & Drivetrain 19 07-12-2009 05:34 PM
clanking or clinking noise joeyz10 Nissan 370Z General Discussions 5 05-01-2009 03:54 AM


All times are GMT -5. The time now is 08:49 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2