Attention Owners of 2010 370Z - Clunk Noise from Rear of Vehicle

DEpointfive0 · 10-22-2012, 10:38 PM

I have a 2009 auto and it makes a beautiful sound like yours when I am coming at a complete stop from almost any speed... ESPECIALLY if I am in manual mode, when it shifts down to 1st, I feel/hear a loud clunk

DEpointfive0 · 10-22-2012, 11:29 PM

Quote:

Originally Posted by ShutokuZ

I had that exact same issue with my Evo IX. The clunk would happen, while backing up and I applied the brakes. The issue was diagnosed as the brake pads "shifting", due to the lack of shims. I replaced the shims and the clunk was gone!

Quote:

Originally Posted by 50 plus

I had the same problem with my 04 Quest minivan and it was due to shifting brake pads in the carrier when you shift from reverse to drive or sometimes drive to drive. Lubed up back of pads and tab slots with high temp brake lube worked for a period of time...Knowing what the noise was reassured me of no serious problems so when the noise returned some time later didn't do anything till brake change.

Quote:

Originally Posted by ShutokuZ

Same here, I put RB500 pads on my Brembo's. Since they were really thick, couldn't put the shims on. Once the pads wore down a little, they started to "shift" causing the clunk. Put new shims on and the clunk was gone.

At the three above posters... REALLY? I always have used shims in my past cars and my dad NEVER does (on the same cars), and I have never had an issue either way...

Quote:

Originally Posted by Mr&Mrs

My 7AT was doing this for a while and it was driving me nuts, only low speeds, and very loud. I happen to get a nail in one of my rear tires and when getting it patched the tech noticed my TPMS was missing. It was inside the wheel.

My light never came on beacause it was still transmitting LOL! After we took it out no more clunk.

REALLY??? Maybe I'll check that?

DEpointfive0 · 10-22-2012, 11:32 PM

Quote:

Originally Posted by jgalloner

I've actually been in contact when Nissan Consumer affairs to discuss this issue. I don't buy the idea that this is a normal characteristic of a $30K+ sports car; especially since it wasn't doing it when I first bought the car.

I hope to hear back from them this week; I wanted some other owner's feedback just to make sure I wasn't being unreasonable with my expecting them to fix the problem under warranty...we'll see if they stand by their products or not I guess.

If they blow you off and you need someone higher up at corporate in consumer affairs, shoot me a PM... I had a problem with my 09 Maxima's brakes not working and they KINDA sucked, but the guy I finally got too was AMAZING, and I even became friends with him... (Just be amped up when you talk to him, he's a fast talker)

jgalloner · 10-23-2012, 07:48 AM

Quote:

Originally Posted by DEpointfive0

If they blow you off and you need someone higher up at corporate in consumer affairs, shoot me a PM... I had a problem with my 09 Maxima's brakes not working and they KINDA sucked, but the guy I finally got too was AMAZING, and I even became friends with him... (Just be amped up when you talk to him, he's a fast talker)

DEpointfiveO, thanks - I'm supposed the hear back from Consumer Affairs by this Thursday, so I'll know more then.

Everybody, I appreciate your feedback. Hopefully this ends on good terms with Nissan. I really love the Z, so it's been quite frustrating.

wheee! · 10-23-2012, 08:29 AM

Not normal at all... Good luck! In for the resulting cause....

ShutokuZ · 10-23-2012, 01:05 PM

Quote:

Originally Posted by DEpointfive0

At the three above posters... REALLY? I always have used shims in my past cars and my dad NEVER does (on the same cars), and I have never had an issue either way...

REALLY??? Maybe I'll check that?

Really..... It all depends on the calipers and the type of brake pads used. Mine was the lack of shims and I know that for a fact. Install new thick pads with no shims, no sound. Wear down pads with no shims, got sound. Install shims (no other changes), no more sound.

jgalloner · 10-24-2012, 11:34 AM

Update - I heard back from Nissan Consumer Affairs today and was told that there's nothing they can do. Apparently they really do not stand behind their products.

I've seen posts here regarding brake pads/shims. I only have 4500 miles on the car and the brakes/pads are the OEM.

Anybody have any suggestions on how I can proceed?

Jordan Farris · 04-08-2013, 05:02 PM

My car doesnot but used to. What I did was took it to a repair shop, in New York sissions auto body is great but not from other states and they had the car for a few weeks and they took the whole rear end off and replaced it with a newer models rear end. I advise u do this.

juld0zer · 10-14-2013, 12:29 PM

i'm also going to vote something with the brakes.

if those are the OEM pads, that's not how the rotor surface should look.
if it's possible, do a full bed-in and see if that helps.
just dont come to a complete stop during or after the procedure. instead, head for the motorway and drive for 5-10mins to cool down the brakes.
You will need to predict the lights and brake very gradually to avoid coming to a stop. if you must stop, use the handbrake to hold the car.

secondly, if i roll (forwards or backwards) and yank the handbrake up, it will make that sound in the video.

thirdly, OEM pads shouldnt vibrate or groan when you let go of the pedal slightly. they release quite smoothly and without noise.
to me, it looks like some material on the rotor surface that is affecting the performance of the brakes. similar to when you wash your car and hose the wheels, create brown rusty deposits on the rotors and back your car out. the brakes are super sensitive for the first couple of light applications, then return to normal.

srbrubak · 10-14-2013, 05:43 PM

My 2010 doesn't make that noise.

chops · 10-14-2013, 06:08 PM

are you guys braking hard? i always hear a distinct clunk when i press the brakes pretty hard. its just the ABS doing its thing i've always assumed. only happens when i brake quickly to a stop. ive taken apart most of my suspension/brakes and theres absolutely nothing wrong, and therefore doesnt even bother me anymore

woops, didnt realize this thread was a year old haha

CaymanZ · 11-02-2013, 01:26 AM

I have a 2010 Z and it makes the same sound when i shift from park or if i speed up slow down. it is very annoying nice looking car but a lot of clicks, clanks and rattles.

juld0zer · 11-02-2013, 12:09 PM

that sounds more like symptoms of the dreaded axle click since it occurs to you when you load/unload the rear axles.
it sounds most like a metallic clicking noise but that's the most i can say without hearing it.

if it's really bad, it will click every time you accelerate and let go of the pedal, and also going from a forward gear to reverse and vice versa.
should be able to hear it driving next to a kerb with the windows down

i've eliminated all my cabin rattles.
i have tried to fix my axle click problem, even following the FSM but i think the torque spec for the nut is insufficient. currently have the right side done up to 115nm, left side is on the factory spec 105nm.

DOOMMONKEY777 · 11-04-2013, 03:37 PM

dude take off ur wheel, start tighening all the nuts and bolt, do not over tighten them just look for the one that is loose check all of em, on brakes on knuckles, on suspension might be undder tencion but it should be farely loose, and look for bad bushings that are worn also must be changed am shure u will find something. Gl

LennyZCSD · 07-04-2014, 05:40 PM

Quote:

Originally Posted by redline727

To me it didn't sound like an axle or rear diff sound. It sounds like a braking sound like something loose with the clamping of your caliper on your pad. I wonder if it only happens under load, or if happened off the ground while on the lift as well?

I also with a 2010 have a noise as this started at about 30,000 does it also by engaging and disengaging the clutch at low speeds I am bringing it in on Monday.
I believe it is from play in the splines

10-23-2012, 08:29 AM	#35 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	Not normal at all... Good luck! In for the resulting cause.... __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

10-14-2013, 06:08 PM	#41 (permalink)
chops A True Z Fanatic Join Date: Oct 2010 Location: NA Posts: 1,732 Drives: NA Rep Power: 22	are you guys braking hard? i always hear a distinct clunk when i press the brakes pretty hard. its just the ABS doing its thing i've always assumed. only happens when i brake quickly to a stop. ive taken apart most of my suspension/brakes and theres absolutely nothing wrong, and therefore doesnt even bother me anymore woops, didnt realize this thread was a year old haha Last edited by chops; 10-14-2013 at 06:10 PM. Reason: holy thread bump

11-04-2013, 03:37 PM	#44 (permalink)
DOOMMONKEY777 A True Z Fanatic Join Date: Oct 2010 Location: Crooklyn Posts: 1,008 Drives: 370Z 6psd-sport-pkg Rep Power: 21	dude take off ur wheel, start tighening all the nuts and bolt, do not over tighten them just look for the one that is loose check all of em, on brakes on knuckles, on suspension might be undder tencion but it should be farely loose, and look for bad bushings that are worn also must be changed am shure u will find something. Gl __________________ Kids don't do Drugs, Drugs are bad, so let the professional druggies do Drugs for you. 537whp/496lb/tq@8-9PSI 93 octane

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ATTENTION: ALL Nismo 370Z Owners: Please check your suspension!	G Fo12ce	New Nismo 370Z Owner	165	12-31-2018 05:36 AM
Attention Work GS4 Owners, what are you using to clean your wheels?	Wiggins3377	Detailing / Washing / Waxing / Cosmetic Maintenance and Repair	4	07-03-2012 09:53 PM
Noise in 1st/2nd - NOT clunk, clank, whine	Davey	Engine & Drivetrain	8	05-16-2011 02:44 PM
Clunk Noise under accel/deccel Files INC	GonGo	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	6	03-11-2011 10:51 AM
Let's take a Poll on how many 2010 Z owners are getting the high pitched noise	Hi-Step'n370Z	Nissan 370Z General Discussions	8	04-06-2010 09:55 PM

10-22-2012, 10:38 PM	#31 (permalink)
DEpointfive0 Premium Member Bitches Join Date: Jan 2012 Location: SoCal Posts: 14,824 Drives: a lot Rep Power: 17151	I have a 2009 auto and it makes a beautiful sound like yours when I am coming at a complete stop from almost any speed... ESPECIALLY if I am in manual mode, when it shifts down to 1st, I feel/hear a loud clunk

10-24-2012, 11:34 AM	#37 (permalink)
jgalloner Base Member Join Date: Sep 2011 Location: Michigan Posts: 8 Drives: 2010 Nissan 370Z M6 Rep Power: 14	Update - I heard back from Nissan Consumer Affairs today and was told that there's nothing they can do. Apparently they really do not stand behind their products. I've seen posts here regarding brake pads/shims. I only have 4500 miles on the car and the brakes/pads are the OEM. Anybody have any suggestions on how I can proceed?

04-08-2013, 05:02 PM	#38 (permalink)
Jordan Farris Base Member Join Date: Mar 2013 Location: Farmersville New York Posts: 11 Drives: 2009 Nissan GTR Rep Power: 12	My car doesnot but used to. What I did was took it to a repair shop, in New York sissions auto body is great but not from other states and they had the car for a few weeks and they took the whole rear end off and replaced it with a newer models rear end. I advise u do this.

10-14-2013, 12:29 PM	#39 (permalink)
juld0zer Enthusiast Member Join Date: Nov 2012 Location: Sydney Posts: 428 Drives: 11 Nissan 370Z MB M6 Rep Power: 139	i'm also going to vote something with the brakes. if those are the OEM pads, that's not how the rotor surface should look. if it's possible, do a full bed-in and see if that helps. just dont come to a complete stop during or after the procedure. instead, head for the motorway and drive for 5-10mins to cool down the brakes. You will need to predict the lights and brake very gradually to avoid coming to a stop. if you must stop, use the handbrake to hold the car. secondly, if i roll (forwards or backwards) and yank the handbrake up, it will make that sound in the video. thirdly, OEM pads shouldnt vibrate or groan when you let go of the pedal slightly. they release quite smoothly and without noise. to me, it looks like some material on the rotor surface that is affecting the performance of the brakes. similar to when you wash your car and hose the wheels, create brown rusty deposits on the rotors and back your car out. the brakes are super sensitive for the first couple of light applications, then return to normal.

10-14-2013, 05:43 PM	#40 (permalink)
srbrubak Base Member Join Date: Nov 2010 Location: Cedar Rapids, Iowa Posts: 144 Drives: 2010 370Z Blue 6MT Rep Power: 14	My 2010 doesn't make that noise.

11-02-2013, 01:26 AM	#42 (permalink)
CaymanZ Base Member Join Date: Sep 2013 Location: San Antonio Posts: 2 Drives: 370 Z Rep Power: 12	I have a 2010 Z and it makes the same sound when i shift from park or if i speed up slow down. it is very annoying nice looking car but a lot of clicks, clanks and rattles.

11-02-2013, 12:09 PM	#43 (permalink)
juld0zer Enthusiast Member Join Date: Nov 2012 Location: Sydney Posts: 428 Drives: 11 Nissan 370Z MB M6 Rep Power: 139	that sounds more like symptoms of the dreaded axle click since it occurs to you when you load/unload the rear axles. it sounds most like a metallic clicking noise but that's the most i can say without hearing it. if it's really bad, it will click every time you accelerate and let go of the pedal, and also going from a forward gear to reverse and vice versa. should be able to hear it driving next to a kerb with the windows down i've eliminated all my cabin rattles. i have tried to fix my axle click problem, even following the FSM but i think the torque spec for the nut is insufficient. currently have the right side done up to 115nm, left side is on the factory spec 105nm.