Issues

onzedge · 07-17-2012, 08:41 AM

Quote:

Originally Posted by tmjohansen

Is there a window reset? When I open the door in drops down the normal inch or so...but it doesn't go back up when the door is closed.

Here is the reset procedure, you need to do it for each window.

Help: Adjusting/aligning window (need more help than just window-reset procedure)

gy954 · 07-17-2012, 02:04 PM

INITIALIZATION PROCEDURE
1. Disconnect battery negative terminal or power window switch connector. Reconnect it after a minute or
more.
2. Door switch is OFF (close).
3. Turn ignition switch ON.
4. Operate power window switch to fully open the window. (This operation is unnecessary if the window is
already fully open.)
5. Continue pulling the power window switch AUTO-UP. Even after glass stops at the fully closed position,
keep pulling the switch for 3 seconds or more.
6. Initializing procedure is completed.
7. Inspect anti-pinch function.
CAUTION:
When initialization is not complete, power window UP does not operate while door is open.
CHECK ANTI-PINCH FUNCTION
1. Fully open the door window.
2. Place a piece of wood near the fully closed position.
3. Close door glass completely with AUTO-UP.
• Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.
• Check that glass does not rise when operating the power window main switch while lowering.
CAUTION:
• Never check with hands and other part of body because they may be pinched. Never get pinched.
• Check that AUTO-UP operates before inspection when system initialization is performed.
• Perform initial setting when auto-up operation or anti-pinch function does not operate normally.
• Finish initial setting. Otherwise, next operation cannot be performed.
1. Auto-up operation
2. Anti-pinch function
3. Key cylinder switch power window function
4. Automatic window adjusting function
5. Auto-up, manual-up does not operate when door is open

PapoZalsa · 07-18-2012, 07:16 PM

PO, Did you resolved the battery issue?

tmjohansen · 07-18-2012, 07:20 PM

I have not. I am now trying to get the battery out.

tmjohansen · 07-27-2012, 01:29 AM

Well I got the battery out and took it to the dealer last week. They tested the battery and stated it looked fine, but couldn't tell with out the car present. I put it in the car and it was still completely dead. Looks like it will be going to the dealer anyways.

07-17-2012, 02:04 PM	#32 (permalink)
gy954 Base Member Join Date: Mar 2012 Location: Sonoma County, CA Posts: 163 Drives: 2011 370Z Rep Power: 181	Service Manual page PWC-7 INITIALIZATION PROCEDURE 1. Disconnect battery negative terminal or power window switch connector. Reconnect it after a minute or more. 2. Door switch is OFF (close). 3. Turn ignition switch ON. 4. Operate power window switch to fully open the window. (This operation is unnecessary if the window is already fully open.) 5. Continue pulling the power window switch AUTO-UP. Even after glass stops at the fully closed position, keep pulling the switch for 3 seconds or more. 6. Initializing procedure is completed. 7. Inspect anti-pinch function. CAUTION: When initialization is not complete, power window UP does not operate while door is open. CHECK ANTI-PINCH FUNCTION 1. Fully open the door window. 2. Place a piece of wood near the fully closed position. 3. Close door glass completely with AUTO-UP. • Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops. • Check that glass does not rise when operating the power window main switch while lowering. CAUTION: • Never check with hands and other part of body because they may be pinched. Never get pinched. • Check that AUTO-UP operates before inspection when system initialization is performed. • Perform initial setting when auto-up operation or anti-pinch function does not operate normally. • Finish initial setting. Otherwise, next operation cannot be performed. 1. Auto-up operation 2. Anti-pinch function 3. Key cylinder switch power window function 4. Automatic window adjusting function 5. Auto-up, manual-up does not operate when door is open

07-18-2012, 07:16 PM	#33 (permalink)
PapoZalsa A True Z Fanatic Join Date: Nov 2009 Location: Not in Sunny Florida Posts: 6,358 Drives: 16 Nismo w/Tech Pack Rep Power: 4500	PO, Did you resolved the battery issue? __________________ 2009 370Z MB Base w/Sport Package 6MT Modshack's Custom Air Intakes /3M Clear Bra/ Illuminated Kick Plates / F. I CBE w/12" resonators / EVO-R Front Lip / Rear Hatch Wing / Tein S-Tech Springs /Ilegal Tint in the Rep. of VA/4x20mm Z1 Spacers/ Vinyl Roof/Liquid Carbon Designs

07-18-2012, 07:20 PM	#34 (permalink)
tmjohansen Base Member Join Date: Jun 2010 Location: Omaha,NE Posts: 230 Drives: 40th Anniversary Z Rep Power: 15	I have not. I am now trying to get the battery out. __________________ 2010 40th Anniversary 2003 Toyota Highlander Limited Nebraska Huskers Boston Red Sox

07-27-2012, 01:29 AM	#35 (permalink)
tmjohansen Base Member Join Date: Jun 2010 Location: Omaha,NE Posts: 230 Drives: 40th Anniversary Z Rep Power: 15	Well I got the battery out and took it to the dealer last week. They tested the battery and stated it looked fine, but couldn't tell with out the car present. I put it in the car and it was still completely dead. Looks like it will be going to the dealer anyways. __________________ 2010 40th Anniversary 2003 Toyota Highlander Limited Nebraska Huskers Boston Red Sox

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
MBC issues?	AWX Z34	Forced Induction	7	04-06-2012 11:13 PM
370 z top issues	sue z	New Forum Member	4	04-30-2011 08:55 PM
Aux-In Issues	christian370z	Audio & Video	2	08-10-2010 03:36 PM
thinking of buying 370z, then GTM turbo's , but overheat issues,oil issues ??	Christopher	Nissan 370Z General Discussions	19	10-16-2009 04:55 PM
Initial Z issues that are now non-issues......	cave vulture	Nissan 370Z General Discussions	1	09-06-2009 11:19 PM