Price check on labor for mod install

KevinB

Want opinions for labor cost to install the following mods:

Stillen Gen 3s
Stillen front/rear sways
FI test pipes
FI cat back exhaust

Local performance shop says 450 for everything. Labor time 5.5 hrs. Sound reasonable? I can do all but test pipes but will take me slot longer probably!

__________________
09 6MT MB: Int/Ext LEDs, Stillen G3 + FI test pipes + FI cat back + Stillen sways + Clutch Helper Spring

TerribleONE

sounds like a pretty fair deal to me..

__________________

kenchan

yah 80-90/hr is reasonable i think. but intakes should take a shop no more than 1hr, front/rear swaybars no more than 45min total . pipes and exhaust 2hrs max.

total 3.5hrs-4hrs maybe?

TerribleONE

I highly doubt even a shop could get the intakes done in 1hr unless they have 2-3 guys on it.. pulling the bumper, cutting, ect takes a while if they are careful which they should be..

__________________

toplessdottie

Sounds fair to me..... especially for a qualtiy job

__________________
Chris
'70 Datsun 2000 Roadster
'09 370z- Invidia, Stillen G3, ZEnclosure

onzedge

Sounds about right.

__________________

Koni|Swift|Michelin|Motordyne|Berk|RJM Performance|Gates|SPL|Motul|Technafit|Ate Super Blue|Hawk
Tommy Kaira|Momo|Optima|Hella|Hotchkis|Red Line|ZSpeed|Stillen|B&M|H&R

brucelidat

Yeah, I would estimate 5-6 hours. $75-$80 an hour is reasonable.

__________________
Works Emotion CR Ultimate - FI CBE w/ 18" resonators - Ecutek - eibach sways - Quaife - FI LTH w/race cats - kw v3 - spl - Topgunz SC - 488whp 398trq

SPOHN

Hold them to that when they figure they can't get the cats off the car with ease.

__________________

CBRich

Listen to SPOHN. And tell them you want the OEM stuff back. Those cats are worth money and you don't want to have to buy new ones when you sell the car. IF they don't hack them up getting them off.

Amuse370z

Sorry to hijack but what should I expect for:

Amuse Body Kit
Exhaust + HFC
Akebono BBK
H&R Spring (Replace with new rims when finish)
GTR Start button

red6spd

Ever think about doing the intakes and CBE yourself? Its real easy.

__________________
2010 Base+Sport 6spd: Stillen G3, FI Non-Resonated CBE, FI Non-Resonated Test Pipes, UpRev Tuned, Custom 24R Oil Cooler, JDM Rear Fog-OEM Harness.
???Whp ???WTQ (Will find out come spring time)

KevinB

Thanks for the words of encouragement ... It was a sunny weekend so I did install the intakes, frothy and rear sways, test pipes and cat back. I spent about $120 in parts and saved 330 in labor. I will argue that the cats are a huge pain in the *** to remove. With that being said once you remove them changing things out is easy. I made sure to replace the demon bolt with a quality aftermarket one that I can get off easier without damaging it.

This forum is awesome. I got lots of good ideas on the cat install. Lots of pb blaster, 1/2" impact six point socket, three ten inch extensions and a huge breaker bar (can get all at harbor freight for 50 total) did the trick.

__________________
09 6MT MB: Int/Ext LEDs, Stillen G3 + FI test pipes + FI cat back + Stillen sways + Clutch Helper Spring

kenchan

good job, kevin. nothing like doing your own mods.

and if you have one of those hydraulics with the removeable extension handle, you can use that extension over your breaker as a cheater bar extension.

Alchemy

Congrats. Nothing like spinnin your own wrenches

__________________
Ryan
314WHP | 260LB-FT | STILLEN | KONI | SWIFT | STOPTECH | Z1 | PROJECT MU | CNT | UPREV | FORGESTAR | BRIDGESTONE | PWJDM | ENEOS | MOTUL