Install Shift Knob
 

Has anyone used this Nismo shift knob on previous Z's. ? what was your impression? I found one for the 370z, the stocker just feels so fat.

Also, how difficult is it to install this thing? the one I installed in my Cooper S required removing the shift boot assembly, etc.

Thanks :-)

Braden

while uninstalling it is fairly easy.. be prepared to murder your stock knob to get it off because they use so much lock tight... see this thread for reference... Shift Knob : Help with Removing - MyG37
.

Thanks for the link :tup:

no problem.. now wheres my rep points? ;) :rock:

This is for the 350Z!!!!!!!!!!!!!!!!


Stock Shift Knob Removal and Replacement

Removing the stock shift knob is not difficult, but certain precautions must be taken to prevent damaging both interior trim pieces and the shift mechanism of the transmission.

[edit] Materials and Tools
A medium sized flat-head screwdriver

Electrical tape

A 6" piece of radiator hose or other heavy rubber tubing.

One pair of channel-locks

One pair of vice-grips

[edit] Procedure

Incorrect method1. Wrap the tip of your screwdriver in a small piece of electrical tape to prevent it from marring the interior trim piece.

2. Insert the screwdriver tip under the boot finisher at the rear and pry up the finisher. There are several clips holding this piece on that will take a fair amount of force to pop loose.

3. Once the finisher is free of the retaining clips, disconnect the white ribbon cable for the climate control knobs. Pull on the connector, not the cable.

4. The finisher will still be attached to the shifter-shaft by the shift boot at this point. It's helpful to have a second person that can hold the finisher up while rotating the knobs, but it's not necessary.

5. Cut the radiator tubing into two 3 inch lengths and slice each one lengthwise down one side.

6. Place one piece of radiator tubing around the metal shifter-shaft underneath the finisher. Be careful not to pinch the boot or tear the white filler-pad sitting on the top of the transmission.

7. Clamp the vice-grips onto the radiator tubing covering the shifter-shaft as tightly as you can. It is important that you get this tight enough so that you can use the vice-grips to provide counter torque when twisting the knob off and the shaft doesn't turn inside the rubber tubing.

8. Take the other piece of tubing and place it around the base of the stock shift knob.

9. Place the channel-locks on the radiator tubing covering the stock shift knob and turn the knob counter-clockwise while applying counter-torque to the vice-grips. The goal is to prevent the counter-clockwise torque from being transferred into the shifter assembly, as this can damage the transmission. If the vice grips slip on the shaft, set the grip tighter. You will not hurt the shifter-shaft by doing so. The boot and finisher will turn initially until the knob is backed off a turn or two. Ensure that the boot does not twist or tear away from the ring under the shift boot.

10. Once the shifter is loose enough to turn by hand, remove the knob and the brass-ring underneath it. This ring is not needed on the new shift-knob, and if you are using a Nismo variant, the ring will actually rattle if you keep it in place because the new knob does not seat against the ring.

11. Once the stock knob is removed, clean up the threads of the shifter shaft and install the new knob onto the shaft. If the new knob came with a rubber finisher, this finisher goes above the boot to cover the metal ring that holds the boot leather in place. Most aftermarket shifters have a nylon insert that you will thread onto the shifter shaft. This might take some force the further you get it threaded onto the shaft.

12. Tighten the shift knob down so that it's tight against the boot ring (or rubber finisher, if equipped) while holding the vice-grips to prevent torque from being applied to the shifter assembly. If equipped with rubber finisher, do not tighten the knob to the point that it distorts the finishers shape. Hold the shift-boot ring in place while tightening. When complete, remove the vice-grips.

13. Re-attach the white ribbon cable for the climate controls.

14. Snap the shift-boot finisher in place.

Enjoy!

Tips for any '08 owners: (Applicable specifically to NISMO style knobs) There are several notes anyone with a later model should pay attention to while performing this task. There is a second rubber boot on the shifter shaft, underneath the paper filler. The best thing to do here, when attatching the vice grips, is to fold that boot over to expose the metal shaft. The exposed section should then be wrapped in the rubber tubing and then gripped with the vice grips. Now once the stock knob has been removed, also grab the ring that rest on the tapered portion of the shaft below the threads. The NISMO knob will not fit properly with that ring. Once it's gone, start screwing down the new one. Be careful when torqing. NISMO knobs are have plastic threads in them and will strip out if excess torque is applied. I got lucky, for when the torque was just right, the NISMO logo was facing toward the driver seat. Now, with the knob installed, you should notice that the shift boot has a little gap between its bottom seat and the knob. If you knob kit came with a rubber ring or shoe that would fill it in, more power to you. Mine did not, so I got to improvise. With the finisher panel still free, slide the boot up to the bottom of the shift knob and wrap a couple zip ties around the shifter shaft and the underside of the boot. This will get it to sit flush, and make it look a lot cleaner. Finally, stick the shift position decal on, attach the ribbon cables, clamp the finisher down, and take it out for a test drive. The drive will make sure the transmission was not damaged during the installation.

Dad, thanks for that :-) Sounds easy so I attempted it today.

See attached pics for results: Sorry for the iphone pics

The F*#k#@%g knob would not come off, I did everything, radiator hose, etc. etc. I finally gave up, because it kept slipping, so I just went for it and put channel locks directly on the knob, then it finally started to turn. After completely destroying the OEM, it was off.

My Nismo knob came with the same instructions and was listed to fit 370z, although there is no way the rubber finisher mount would fit below the shifter knob, it wouldn't ever begin to thread on, it's like the shifter stalk was too short. So I put it on without the rubber finisher, and it seam to go on fine.
I used the stock plastic boot holder with zip tie under the shifter, seams to work as well.

Now I have to get use to it, I love the look, just feels a bit thin compared to the OEM.

^^Looks about right!! The Nismo looks nice. I remember the first time I tried to remove one on the 350Z.... took me only 10 minutes to break-out the vise-grips. Even then it was still a pain in the ***!!

That looks really good minicobra, nice work. :tup:

Metal knobs are too hot for phoenix, but they sure look good!

I like the shift knob..http://animepisodes.info/images/1a0a...8a05200e32.jpg

One of my favorites...

VERTEX Monochrome Shift knob White

I just installed this one... absolutely love it.


http://www.forgedperformance.com/sto...t_16198_02.jpg

Which one is that?

friend has something very similar in his STI.. i loved the way it felt.. i had an arc on my g37.. looking for something with more grip this time around.

Hey i really do not like the stock 370z shift knob....i really would like to purchase a metallic orange smaller maybe thinner shift knob to better accommodate me....and i think it would look fly with the persimmon seats and orange gauges the car comes with..... i use to have an 2008 civic si so i was use to that type of shift knob....can some one please send me a link or send me some pics thank you

I've got the RAZO Super Lo knob, it weighs 450g and is offset to the rear a little. I love it, fits perfectly and looks good too. I'll take a couple pics tomorrow if anybody's interested

^Pics! :)

I love it, it was real easy to install on the Z, my Spec V required some cutting but it just went right on, I threadlocked it and it doesn't budge during hard shifting

http://img683.imageshack.us/img683/8745/dsc02128.jpg

http://img683.imageshack.us/img683/7121/dsc02129.jpg

http://img193.imageshack.us/img193/6389/dsc02130k.jpg

Looks good!

Your interior is much cleaner than mine, lol

Haha, thanks man. I hope it does, I just picked the car up tonight :)
I got the knob for like $50, somewhere on the internet, found it on Google, good price, I thought

Haha, missed your intro thread til just now - welcome!

Thank ya brother

:iagree: im in south fl and it burns your hand here too

Do you have the BM short shifter as well, or is that stock height with the new knob?

from what I have heard, removing the original shift knob usually means it's going to be destroyed, because of the locktite used to install them from the factory..

I'd be curious if anyone has located a shift knob that would compliment the red stitching of the Nismo interior. I like the stock one, but I would have loved to see Nismo showcase that red a little more on the shifter.

People that destroyed the stock knob didnt remove it carefully, if you use a piece of radiator hose on the leather part and a pair of channel locks, it twists right off with some elbow grease.

My stock knob was fine. I just wrapped a towel around the knob and used a vice to keep it in place while using a screwdriver through the end/bottom of the shifter as leverage.

Here's a link to my DIY for the AMS short shifter kit install:
http://www.the370z.com/diy-section-d...r-install.html

Do any of you guys know anything about a shift knob replacement for the 7AT? I feel kinda left out. :confused:

It can be very difficult, I have not sat in the 7AT since my test drive (6 months ago), but does it have a button on it to "release" it and move through the different options?

If so it can be hard to find a replacement as you have to have one that has that release button and such, usually.

I twisted my knob off with my hand. It took a couple tries, but it didn't hurt the threads or the outside. I haven't had the knob on in the summer, but in cold weather, it gets real cold. I can imagine it's going to end up burning my hand

I never had a metal shifter in my 350, but it did have that metal cap with the shift pattern on it that got pretty hot in the summer. After a few times where I swear I burned the shift pattern into my palm, I bought a nice little hand towel that I kept in the car to simply cover the shifter (or I simply used a hat). This solved all heat issues for me and might not be a bad idea for those of you with the metal knobs.

Yeah that lil plate burnt me many times in the summer. For some reason I would always forget and a minute later I'd burn myself again...

Let me clarify... the towel was used for when the car was parked, not when I was driving the car.....

metal shift knobs are great but they do get super hot and super cold with the seasons.

i know cause i use them on my other cars.

My girlfriend got me the black Nismo shift knob for x-mas early and I put it on tonight. It took me two wrenches and about 15 minutes to get that damn stock knob off, completely destroying it in the process...

The rubber fitment piece it comes with is way too thick so I had to cut in half to get the top of the boot to sit flush with the bottom of the knob. I love the look and feel of this one, and my car is parked in an underground garage so I never have to worry about coming out to a hot/cold car.

Some iPhone pics:

Half of the destroyed stock knob
http://i229.photobucket.com/albums/ee127/tru610/asd.jpg

New installed
http://i229.photobucket.com/albums/e...10/photo-1.jpg

looks nice man :tup:

btw here's my favorite shift knob Blake. I just can't justify the $425 price :ugh:

ZELE titanium
http://www.rhdjapan.com/images/produ...mal/Image1.jpg

http://www.rhdjapan.com/images/produ...mal/Image2.jpg

$425 for a shift knob....WOW....that's nuts!

Made by Gucci or???

AK has expensive taste :tup: