What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

zeeder · 08-25-2021, 08:57 PM

Quote:

Originally Posted by zeeder

Well, I tried to install the base tune, from Specialty Z, last night and got an error. Looks like there might already be an UpRev tune on the car so I've reached out to a local shop that uses UpRev to see if they can flash it back to stock so I can install the ECUTek Tune. Hopefully they're able to!

Great news, the shop was able to revert me to the stock tune and I got the base tune from Seb installed and the first logs sent off to him. Weirdly, I didn’t notice much difference between the UpRev tune and the stock tune. That said, the throttle mapping in the lower revs is much better with the ECUTek tune! It’s hot as hell here right now so we’re just working on the warm weather tune lol.

k67p67 · 08-26-2021, 02:07 PM

A few months back I experienced a rotator cuff injury. Been on the mend since then. Certain movements are really painful, one of them being lifting a wheel and sliding it onto the studs. Even with light 3-piece wheels, the wheel+tire weighs 45-50 lbs. I was looking for some kind of aid to help me raise a wheel and hold it while I clocked it to line up the studs. At first I tried a floor jack but clocking the wheel was difficult. I decided to try a wheel dolly as it could perform both the lifting function and allow easy clocking of the wheel face to facilitate mounting. I couldn't be happier with the results and would recommend this to anyone in a similar situation. The dolly was about $125 and I picked up some rollerblade-type wheels for $25 because the original ones were crap. I had to build a plywood platform to add height when the car is way up on jack stands but, at lower levels, the dolly is all that is needed.

08-26-2021, 02:07 PM	#2 (permalink)
k67p67 Enthusiast Member Join Date: Oct 2016 Location: Rancho Cucamonga, CA Posts: 311 Drives: 2017 Nismo Tech 6MT Rep Power: 3937	A few months back I experienced a rotator cuff injury. Been on the mend since then. Certain movements are really painful, one of them being lifting a wheel and sliding it onto the studs. Even with light 3-piece wheels, the wheel+tire weighs 45-50 lbs. I was looking for some kind of aid to help me raise a wheel and hold it while I clocked it to line up the studs. At first I tried a floor jack but clocking the wheel was difficult. I decided to try a wheel dolly as it could perform both the lifting function and allow easy clocking of the wheel face to facilitate mounting. I couldn't be happier with the results and would recommend this to anyone in a similar situation. The dolly was about $125 and I picked up some rollerblade-type wheels for $25 because the original ones were crap. I had to build a plywood platform to add height when the car is way up on jack stands but, at lower levels, the dolly is all that is needed. __________________ SOLD2017 370Z Nismo Tech 6MT PART OUT IN PROGRESS Work \| Motordyne \| Powertrix \| Swift \| Michelin \| Takeda \| Hotchkis \| RJM \| Voodoo13 \| SPL \| SPC \| Z1 Motorsports \| ZSpeed \| Morimoto \| Craft Square Last edited by k67p67; 08-26-2021 at 11:54 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[MAZOC] Official "Off-Topic" Discussion Thread	m4a1mustang	MAZOC	6670	09-06-2018 07:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10007	06-08-2017 09:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 08:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10148	06-19-2014 08:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 11:21 AM