What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

rspray2000 · 08-03-2021, 09:40 PM

Quote:

Originally Posted by JARblue

Leave it in the sun on a hot summer day. Texas sun makes it easy almost any day, but in Massachusetts you might have to wait for the right day. If you use a heat gun just make sure you use it on low heat and be extremely careful not to overheat the paint and clear coat.

That 3M Eraser Wheel is extremely dangerous around paint in the hands of the inexperienced. Better to use a heat gun on low first. I wouldn't use the eraser wheel except as a last resort and keep the RPMs low and slow.

You have any experience with removing baked-on, cracked Roadster top liners? Most posts I’ve seen say the same: mild heat and scraping. I tried but it was very messy and slow. I have the adhesive wheel on order. FYI I am tentatively planning to wrap it next year, so may have them take care of it.

JARblue · 08-04-2021, 03:49 AM

Quote:

Originally Posted by rspray2000

I tried but it was very messy and slow.

This is to be expected. Patience is the name of the game. The slower you go the better chance you won't mess anything up. If the adhesive is being stubborn, there is no magic answer for quick removal.

R1talin · 08-04-2021, 05:59 PM

received my morimoto tail lights, and some of my audio upgrade components…
Attachment 147844

Attachment 147845

Attachment 147846

R1talin · 08-04-2021, 08:33 PM

Quote:

Originally Posted by zeeder

Just ordered a tune from Specialty-Z!

Sweet! What upgrades have you done? Would like to compare….assuming you are still NA…

zeeder · 08-05-2021, 09:10 AM

Quote:

Originally Posted by R1talin

Sweet! What upgrades have you done? Would like to compare….assuming you are still NA…

I have a K&N intake, FI Resonated HFC and FI exhaust w/ 18" resonators. All mods were done by a previous owner but I couldn't find a tune cable anywhere so I figured I'd get a tune, mainly for throttle response tweaks and to make sure everything is running decently efficiently.

The car has almost 80k miles and is in great shape and I want to keep it that way! I don't have any major plans to upgrade anything else at the moment since it's my daily driver I'm keeping stock suspension but, if/when things break I'll be upgrading them.

abm89 · 08-05-2021, 05:11 PM

I would ditch that intake if they are short tubes. you would be better off with the stock boxes.

BettyZ · 08-05-2021, 07:08 PM

Quote:

Originally Posted by zeeder

I have a K&N intake, FI Resonated HFC and FI exhaust w/ 18" resonators. All mods were done by a previous owner but I couldn't find a tune cable anywhere so I figured I'd get a tune, mainly for throttle response tweaks and to make sure everything is running decently efficiently.

The car has almost 80k miles and is in great shape and I want to keep it that way! I don't have any major plans to upgrade anything else at the moment since it's my daily driver I'm keeping stock suspension but, if/when things break I'll be upgrading them.

If they're short tubes, ditch 'em. I have a set of low mileage Z1 CAI's for sale. PM if interested.

Sent from my SM-G955U using Tapatalk

abm89 · 08-06-2021, 10:45 AM

I have the Z1's installed. No cutting required, similar gains to the Stillen Gen3. Overall, a great set.

zeeder · 08-06-2021, 03:15 PM

Quote:

Originally Posted by abm89

I have the Z1's installed. No cutting required, similar gains to the Stillen Gen3. Overall, a great set.

My main concern with the long tube headers is the rain/wet as I daily drive my car. How much of an risk/issue is this?

Rusty · 08-06-2021, 03:44 PM

Quote:

Originally Posted by zeeder

My main concern with the long tube headers is the rain/wet as I daily drive my car. How much of an risk/issue is this?

I have the Stillen G3's. I've driven it in flat out down pours with no issues. with the filters up behind the bumper. They're out of the way. But if you use one of those air scoops. That's a different story.

R1talin · 08-06-2021, 06:17 PM

Quote:

Originally Posted by Rusty

I have the Stillen G3's. I've driven it in flat out down pours with no issues. with the filters up behind the bumper. They're out of the way. But if you use one of those air scoops. That's a different story.

Same here, no issues with the long tube CAI

R1talin · 08-06-2021, 06:35 PM

Quote:

Originally Posted by zeeder

I have a K&N intake, FI Resonated HFC and FI exhaust w/ 18" resonators. All mods were done by a previous owner but I couldn't find a tune cable anywhere so I figured I'd get a tune, mainly for throttle response tweaks and to make sure everything is running decently efficiently.

The car has almost 80k miles and is in great shape and I want to keep it that way! I don't have any major plans to upgrade anything else at the moment since it's my daily driver I'm keeping stock suspension but, if/when things break I'll be upgrading them.

being all NA, i'm similar, have Motordyne Shockwave exhaust with ART pipes and long tube Stillen CAI..... these #'s are after the Ecutek tune

getting the tune after the upgrades was a major difference, well worth it IMO in terms of throttle response in the mid range...

also, having launch control is awesome!

..not that it matters for a tune but do have a fortune-auto coil over suspension installed and did the Z1 moto/trans mounts & sub frame/solid diff bushings

zeeder · 08-06-2021, 06:37 PM

Thanks guys! I ended up buying BettyZ’s Z1 long tube intakes. It’ll delay the tune but it’ll give me a chance to see if I feel up to the task of working on the car myself!

BettyZ · 08-07-2021, 04:15 PM

Mish*tmoto thermostatic plate. Typical Mish*tmoto quality control. Their supplied M20 fittings wiggle in the threads like a whore in heat. And that 1/4" port looks real useable.

Only reason I took a chance on their chitty products was I wanted a better way to run the oil feed line than the frankenfitting off the oil pressure sensor port.

Sent from my SM-G955U using Tapatalk

redondoaveb · 08-07-2021, 05:05 PM

Quote:

Originally Posted by BettyZ

Mish*tmoto thermostatic plate. Typical Mish*tmoto quality control. Their supplied M20 fittings wiggle in the threads like a whore in heat. And that 1/4" port looks real useable.

Only reason I took a chance on their chitty products was I wanted a better way to run the oil feed line than the frankenfitting off the oil pressure sensor port.

Sent from my SM-G955U using Tapatalk

I haven't had any issues with mine

08-05-2021, 05:11 PM	#5496 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,382 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	I would ditch that intake if they are short tubes. you would be better off with the stock boxes. JARblue, cv129, Hotrodz and 2 others like this. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

08-06-2021, 10:45 AM	#5498 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,382 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	I have the Z1's installed. No cutting required, similar gains to the Stillen Gen3. Overall, a great set. Hotrodz, redondoaveb and BettyZ like this. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

08-06-2021, 06:37 PM	#5503 (permalink)
zeeder Enthusiast Member Join Date: Jun 2011 Location: Columbia, MO Age: 47 Posts: 460 Drives: ‘13 370Z ST 6M Rep Power: 3428	Thanks guys! I ended up buying BettyZ’s Z1 long tube intakes. It’ll delay the tune but it’ll give me a chance to see if I feel up to the task of working on the car myself! JARblue, Rusty, Hotrodz and 7 others like this. __________________ Zack FI catback, HFC, and Start Button - Z1 Intake - Nismo S-Tune Spoiler - PasswordJDM V2 Shift Knob

08-07-2021, 04:15 PM	#5504 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 37 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	Mishtmoto thermostatic plate. Typical Mishtmoto quality control. Their supplied M20 fittings wiggle in the threads like a whore in heat. And that 1/4" port looks real useable. Only reason I took a chance on their chitty products was I wanted a better way to run the oil feed line than the frankenfitting off the oil pressure sensor port. Sent from my SM-G955U using Tapatalk __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods Last edited by BettyZ; 08-07-2021 at 04:24 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[MAZOC] Official "Off-Topic" Discussion Thread	m4a1mustang	MAZOC	6670	09-06-2018 08:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10007	06-08-2017 10:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 09:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10148	06-19-2014 09:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 12:21 PM