What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

cv129 · 10-11-2020, 02:28 PM

adjusted seating position...I used to like sitting more upright...now I adjusted the thigh support all the way up, moved seat forward one click, and tilt the back support a click or two back, got better butt feel for the car and the seat holds me much better during corner.

abm89 · 10-11-2020, 03:24 PM

I've installed the gauge and routed the wiring. I took it for a test drive and importantly, nothing leaked from what i could see. The cold startup pressure was 80psi (34 row oil cooler installed, i know there's some debate on how that affects overall pressure) but i got it up to about 160-170F and it went to 21-22 psi at idle. Waiting on the Z1 undertray that should come in today before i button everything back up and then go for a drive

Edit: It's 95F here today. So that may play a factor into the "cold" start.

Rusty · 10-11-2020, 03:52 PM

Quote:

Originally Posted by abm89

I've installed the gauge and routed the wiring. I took it for a test drive and importantly, nothing leaked from what i could see. The cold startup pressure was 80psi (34 row oil cooler installed, i know there's some debate on how that affects overall pressure) but i got it up to about 160-170F and it went to 21-22 psi at idle. Waiting on the Z1 undertray that should come in today before i button everything back up and then go for a drive

Edit: It's 95F here today. So that may play a factor into the "cold" start.

Mine is 100 psi cold start and 35 psi hot idle at 90F air temp.

abm89 · 10-11-2020, 04:03 PM

Quote:

Originally Posted by Rusty

Mine is 100 psi cold start and 35 psi hot idle at 90F air temp.

Yeah I saw that. You're also running a heavier oil as well right? either way, If it's in spec, I'll take it for 128K miles. good enough for weekend drives which is all i do these days.

Spooler · 10-11-2020, 05:33 PM

Quote:

Originally Posted by cv129

adjusted seating position...I used to like sitting more upright...now I adjusted the thigh support all the way up, moved seat forward one click, and tilt the back support a click or two back, got better butt feel for the car and the seat holds me much better during corner.

I had to do that too a little over a year back. My foot was coming off the go pedal. 2 clicks forward solved that.

abm89 · 10-12-2020, 06:34 PM

Still waiting on my undertray. I'll blame that on FedEx, but i took another careful drive around the neighborhood to get some data.

Start pressure: 80psi
Idle Pressure at 180F: 22psi
Idle Pressure at 195F: High 18PSI to low 19PSI, it kept jumping back and forth
Pressure at 195F 2000RPM no load: 45PSI

Still no obvious leaks, the max RPM i took it to was a little past 4000 RPM as I still dont have the undertray so im being careful driving anyway. I'm honestly quite glad my car is running alright given 128K miles and 25+ track days (quite a few from hellish summers in TX).

I guess for the purposes of archiving more data here, I've basically serviced this vehicle myself most of the time. I got the car lightly used at 8200 miles and daily drove it until about 110K miles. I've used Redline 5w30 for over 90% of the time except the first change i did, I used mobil 1, and i tried Motul eco energy a 2-3 times. I did use Motul 300V for a back-to-back track day once but removed it the week after. I've had an oil cooler on the car ever since about 27K miles. 25 row stillen gold series until I bought a new 34 row setrab core in 2018.

Rusty · 10-12-2020, 08:27 PM

Quote:

Originally Posted by abm89

Yeah I saw that. You're also running a heavier oil as well right? either way, If it's in spec, I'll take it for 128K miles. good enough for weekend drives which is all i do these days.

I'm using Mobil 1 0w-40 Euro blend.

Z_ealot · 10-13-2020, 03:01 AM

Rolled over the 203,000 mile mark this last weekend, still going! Also got around to having the transmission fluid changed and swapped out the old and starting to rot factory transmission mount for a brand new shiny z1 polyurethane transmission mount....what a difference that made when paired with my already existing poly mount on the differential, really makes it feel like the driveline is more solid and shifting feels more direct and smoother now

abm89 · 10-13-2020, 02:43 PM

Nice! Keep on driving!

abm89 · 10-14-2020, 09:17 PM

While my oil pressures are stable, I'm now having issues with the damn code again, this time i think i feel some resistance when driving (not sure, i've been driving the WRX alot lately). I'm going to revert the catch cans back to the stock PCV routing this weekend.

I have some ECUtek cruising logs if anyone is interested. I doubt the P2A03 and sister codes are coming because of the exhaust now. When i went to replace the gaskets i used last time with the copper ones, there was no leaking on either side of the gasket. I did read in some places that the code will not go away unless you do some reset procedure if you did have a leak before (which i've confirmed way back last year)

abm89 · 10-17-2020, 02:15 PM

Reverted the PCV system to stock routing today. The engine seems fine but now I’m thinking it’s a driveline issue. I’m getting really bad vibrations after i tried to push it just a little. On top of that there’s some sort of ticking noise coming from under the car when it’s in motion, I thought it was exhaust rattle, but It doesn’t seem like it if it continues down the street.

It’s just going to end up sitting for a while until I figure out if it’s worth fixing.

A Black Z34 · 10-17-2020, 03:59 PM

Got dyno’d today. I wanted a baseline before I start doing serious mods. I currently have drop ins and an axelback, so it’s relatively stock. I was spot on with my prediction of 290 though!

Any one have an idea why I was getting a dip in power around 55-6500 RPM? It was different for each pull too. I am waiting to hear back from the shops tuner to see what he says but figure I’d ask y’all as well.

abm89 · 10-17-2020, 04:25 PM

it could be pulling timing, but i've never seen that on our cars.

Rusty · 10-17-2020, 04:29 PM

Quote:

Originally Posted by A Black Z34

Got dyno’d today. I wanted a baseline before I start doing serious mods. I currently have drop ins and an axelback, so it’s relatively stock. I was spot on with my prediction of 290 though!

Any one have an idea why I was getting a dip in power around 55-6500 RPM? It was different for each pull too. I am waiting to hear back from the shops tuner to see what he says but figure I’d ask y’all as well.

Did they dyno it with the VDC off?

DeliriousClam · 10-17-2020, 08:43 PM

Feels SO much better with an actual good tune. Now need to figure out this noise coming from the rear end at 80mph

10-11-2020, 02:28 PM	#5026 (permalink)
cv129 A True Z Fanatic Join Date: Jul 2011 Location: Dallas, TX Posts: 3,222 Drives: 09 Nismo, 16 Nismo Rep Power: 163995	adjusted seating position...I used to like sitting more upright...now I adjusted the thigh support all the way up, moved seat forward one click, and tilt the back support a click or two back, got better butt feel for the car and the seat holds me much better during corner. JARblue, Rusty, old guy and 1 others like this. __________________ Setrab \| RE-71 \| SPL \| JRZ \| Nismo \| ARK \| Whiteline \| RacingBrake \| CJM Oil Pan \| Ti shield

10-11-2020, 03:24 PM	#5027 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	I've installed the gauge and routed the wiring. I took it for a test drive and importantly, nothing leaked from what i could see. The cold startup pressure was 80psi (34 row oil cooler installed, i know there's some debate on how that affects overall pressure) but i got it up to about 160-170F and it went to 21-22 psi at idle. Waiting on the Z1 undertray that should come in today before i button everything back up and then go for a drive Edit: It's 95F here today. So that may play a factor into the "cold" start. old guy and BettyZ like this. __________________ Complete Parts List: https://github.com/abm89/ztouge-build Last edited by abm89; 10-11-2020 at 03:43 PM.

10-12-2020, 06:34 PM	#5031 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	Still waiting on my undertray. I'll blame that on FedEx, but i took another careful drive around the neighborhood to get some data. Start pressure: 80psi Idle Pressure at 180F: 22psi Idle Pressure at 195F: High 18PSI to low 19PSI, it kept jumping back and forth Pressure at 195F 2000RPM no load: 45PSI Still no obvious leaks, the max RPM i took it to was a little past 4000 RPM as I still dont have the undertray so im being careful driving anyway. I'm honestly quite glad my car is running alright given 128K miles and 25+ track days (quite a few from hellish summers in TX). I guess for the purposes of archiving more data here, I've basically serviced this vehicle myself most of the time. I got the car lightly used at 8200 miles and daily drove it until about 110K miles. I've used Redline 5w30 for over 90% of the time except the first change i did, I used mobil 1, and i tried Motul eco energy a 2-3 times. I did use Motul 300V for a back-to-back track day once but removed it the week after. I've had an oil cooler on the car ever since about 27K miles. 25 row stillen gold series until I bought a new 34 row setrab core in 2018. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

10-13-2020, 03:01 AM	#5033 (permalink)
Z_ealot A True Z Fanatic Join Date: Sep 2010 Location: Albuquerque, NM Posts: 2,045 Drives: 09 370Z Touring/Sprt Rep Power: 10091	Rolled over the 203,000 mile mark this last weekend, still going! Also got around to having the transmission fluid changed and swapped out the old and starting to rot factory transmission mount for a brand new shiny z1 polyurethane transmission mount....what a difference that made when paired with my already existing poly mount on the differential, really makes it feel like the driveline is more solid and shifting feels more direct and smoother now God-Speed, JARblue, Rusty and 6 others like this.

10-13-2020, 02:43 PM	#5034 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	Nice! Keep on driving! Z_ealot and Zingston like this. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

10-17-2020, 02:15 PM	#5036 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	Reverted the PCV system to stock routing today. The engine seems fine but now I’m thinking it’s a driveline issue. I’m getting really bad vibrations after i tried to push it just a little. On top of that there’s some sort of ticking noise coming from under the car when it’s in motion, I thought it was exhaust rattle, but It doesn’t seem like it if it continues down the street. It’s just going to end up sitting for a while until I figure out if it’s worth fixing. BettyZ likes this. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

10-17-2020, 04:25 PM	#5038 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	it could be pulling timing, but i've never seen that on our cars. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

10-17-2020, 08:43 PM	#5040 (permalink)
DeliriousClam A True Z Fanatic Join Date: May 2015 Location: NJ Age: 31 Posts: 3,758 Drives: 12 Base Sport Rep Power: 54272	Feels SO much better with an actual good tune. Now need to figure out this noise coming from the rear end at 80mph Hotrodz, redondoaveb and Zingston like this. __________________ Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet MECP Advanced: CEA26671 Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[MAZOC] Official "Off-Topic" Discussion Thread	m4a1mustang	MAZOC	6670	09-06-2018 08:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10007	06-08-2017 10:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 09:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10148	06-19-2014 09:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 12:21 PM