What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

Spooler · 10-08-2019, 09:13 PM

Finding a good alignment guy is tuff.

Rusty · 10-08-2019, 10:37 PM

Quote:

Originally Posted by BettyZ

Got the SPL rear mid-links, FUCAs, and rear camber arms aligned today. Just checked the rear, Firestone's "experienced tech" broke one of the titanium bolts and replaced it with a hex head bolt. Didn't tighten the right camber jam-nut. Didn't torque anything down to spec. What kills me about this is that I literally gave him the instructions, my 3/16" hex bit, and my 1/4" drive torque wrench - and he still ****** it up.. and didn't tell me about the broken bolt - or reset the wrench.

It's like.. dude.. I TOLD you I installed all this myself.. do you not think I'm not going to notice?

I don't care what everyone says about Firestone. I will never take anything to them. The horror stories I've heard over the years about them is unbelievable.

redondoaveb · 10-08-2019, 10:43 PM

Quote:

Originally Posted by Rusty

I don't care what everyone says about Firestone. I will never take anything to them. The horror stories I've heard over the years about them is unbelievable.

I took them a new set of tires and wheels to have the tires mounted and wheels balanced. When I got home I installed the wheels and checked tire pressures. All four had around 50 psi. I guess after they over filled them to set the bead, they neglected to bleed them to the correct pressure. That was enough to convince me to not go back.

CRiZO · 10-08-2019, 11:19 PM

I would never take a car to Firestone or Goodyear. They will literally hire anyone. I know because I've had friends work there. Friends I would never let even drive my car, much less wrench on it.

Ghostvette · 10-09-2019, 09:14 AM

Quote:

Originally Posted by BettyZ

Got the SPL rear mid-links, FUCAs, and rear camber arms aligned today. Just checked the rear, Firestone's "experienced tech" broke one of the titanium bolts and replaced it with a hex head bolt. Didn't tighten the right camber jam-nut. Didn't torque anything down to spec. What kills me about this is that I literally gave him the instructions, my 3/16" hex bit, and my 1/4" drive torque wrench - and he still ****** it up.. and didn't tell me about the broken bolt - or reset the wrench.

It's like.. dude.. I TOLD you I installed all this myself.. do you not think I'm not going to notice?

Quote:

Originally Posted by redondoaveb

Probably didn't replace the bolt with the proper grade bolt either. Sounds like all Firestone store's are alike. No better out here.

Quote:

Originally Posted by Rusty

I don't care what everyone says about Firestone. I will never take anything to them. The horror stories I've heard over the years about them is unbelievable.

Quote:

Originally Posted by redondoaveb

I took them a new set of tires and wheels to have the tires mounted and wheels balanced. When I got home I installed the wheels and checked tire pressures. All four had around 50 psi. I guess after they over filled them to set the bead, they neglected to bleed them to the correct pressure. That was enough to convince me to not go back.

Quote:

Originally Posted by CRiZO

I would never take a car to Firestone or Goodyear. They will literally hire anyone. I know because I've had friends work there. Friends I would never let even drive my car, much less wrench on it.

When I worked for Advance, we had a Firestone AND a Meineke in the same parking lot, plus we delivered to NTB (Now Big O Tires here). They are all fvcking morons. Come to think of it, Tires Plus is marginally better, but they are still idiots.

The NTB we delivered to would regularly break customer lug studs, then charge the customer to replace them.

Zezus · 10-09-2019, 10:10 AM

Quote:

Originally Posted by DeliriousClam

Not today but I went to the drag strip with a few friends and played with my knock-off go pro. Pretty sure I blew out my diff bushing at some point because I was getting a good amount of wheel hop. Need to swap that out and figure out how to make the Z faster

I feel this man.

I blew mine out and have been dealing with it the last couple of months. I finally bought some solid bushings. Just need to find some time to swap them out.

DeliriousClam · 10-09-2019, 07:39 PM

Quote:

Originally Posted by Zezus

I feel this man.

I blew mine out and have been dealing with it the last couple of months. I finally bought some solid bushings. Just need to find some time to swap them out.

I luckily have a guy at work who I actually trust that is willing to do it and relatively cheaply considering how much of a bitch it is

Ian B · 10-10-2019, 03:27 AM

Replaced el wire mood lights for the doors in orange. Here is the original video after install.

https://youtu.be/1-cAagvRDHY

God-Speed · 10-10-2019, 07:42 AM

Quote:

Originally Posted by Ian B

Replaced el wire mood lights for the doors in orange. Here is the original video after install.

https://youtu.be/1-cAagvRDHY

Ian looks cool, will need to check this out on you car.

abm89 · 10-10-2019, 10:35 AM

Not sure my oil gallery gasket is done or if I overfilled the oil on the last change. Noticed some light smoking when i got back home yesterday in traffic (vented hood may have made it obvious), and found oil running up the dipstick when i checked it cold this morning. The level is high so I'm hoping it's just that.

I was able to road trip to and from Houston without any issues, but who knows. I have no codes, so maybe just drive it and let the oil catch cans get some of it/burn off the excess.

Rusty · 10-10-2019, 10:58 PM

Quote:

Originally Posted by abm89

Not sure my oil gallery gasket is done or if I overfilled the oil on the last change. Noticed some light smoking when i got back home yesterday in traffic (vented hood may have made it obvious), and found oil running up the dipstick when i checked it cold this morning. The level is high so I'm hoping it's just that.

I was able to road trip to and from Houston without any issues, but who knows. I have no codes, so maybe just drive it and let the oil catch cans get some of it/burn off the excess.

If it was your oil gallery gaskets. You would never know unless you have an oil pressure gauge or the engine started to make noises. The gaskets leak internally.

Zezus · 10-11-2019, 09:11 AM

Quote:

Originally Posted by DeliriousClam

I luckily have a guy at work who I actually trust that is willing to do it and relatively cheaply considering how much of a bitch it is

i bought a sawzall in preparation. i just really, REALLY dont want to do this..

sp911 · 10-11-2019, 10:13 AM

add Town Fair Tire to the list of tire shops to avoid.

abm89 · 10-11-2019, 11:15 AM

Quote:

Originally Posted by Rusty

If it was your oil gallery gaskets. You would never know unless you have an oil pressure gauge or the engine started to make noises. The gaskets leak internally.

Yeah, you're absolutely right on that one. I'm sure it's an overfill issue. I'll just drive it around and burn the excess off, pretending it's a formula 1 car on startup.... I'm working on getting the PIDs for my dash command software so i can pick up Oil pressure from OBDII, but everything else looks fine. Unfortunately the only oil reading i have available in the car is the temp (which could indicate a failure of some sort, but it's not reliable for pressure readings).

I'd rather be paranoid and have a working car instead of negligent with a broken one. Ideally I'll do the gasket, oil pump, and timing chain all at once in the future.

DeliriousClam · 10-11-2019, 11:27 AM

Quote:

Originally Posted by Zezus

i bought a sawzall in preparation. i just really, REALLY dont want to do this..

The dude is charging me 3 hours of labor at $45/hr since he works for me

10-08-2019, 09:13 PM	#4216 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,803 Drives: 2013 Nismo 370z Rep Power: 2684392	Finding a good alignment guy is tuff. Rusty, Hotrodz, ZontheRocks and 1 others like this.

10-08-2019, 11:19 PM	#4219 (permalink)
CRiZO Track Member Join Date: Nov 2017 Location: Dallas Posts: 672 Drives: in traffic Rep Power: 20699	I would never take a car to Firestone or Goodyear. They will literally hire anyone. I know because I've had friends work there. Friends I would never let even drive my car, much less wrench on it. Rusty likes this.

10-10-2019, 03:27 AM	#4223 (permalink)
Ian B Track Member Join Date: Mar 2011 Location: Cedar Park Posts: 679 Drives: 2010 Nissan Rep Power: 137465	Replaced el wire mood lights for the doors in orange. Here is the original video after install. https://youtu.be/1-cAagvRDHY God-Speed, madwi, abm89 and 3 others like this.

10-10-2019, 10:35 AM	#4225 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	Not sure my oil gallery gasket is done or if I overfilled the oil on the last change. Noticed some light smoking when i got back home yesterday in traffic (vented hood may have made it obvious), and found oil running up the dipstick when i checked it cold this morning. The level is high so I'm hoping it's just that. I was able to road trip to and from Houston without any issues, but who knows. I have no codes, so maybe just drive it and let the oil catch cans get some of it/burn off the excess. God-Speed and BettyZ like this. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[MAZOC] Official "Off-Topic" Discussion Thread	m4a1mustang	MAZOC	6670	09-06-2018 08:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10007	06-08-2017 10:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 09:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10148	06-19-2014 09:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 12:21 PM

10-11-2019, 10:13 AM	#4228 (permalink)
sp911 Enthusiast Member Join Date: Feb 2014 Location: central connecticut Posts: 259 Drives: 2012 370z gun metal Rep Power: 11	add Town Fair Tire to the list of tire shops to avoid.