What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

-ZS-Carpenter · 05-27-2019, 03:06 PM

Quote:

Originally Posted by BettyZ

Jaysus. You're not lowered are you?

Nope, stock height. That cap stuck up about 5"

It was hard to tell pulling in. I saw it but thought i could straddle it no problem. when i look at it from the other angle after hitting it I could see how high it really was. Need to look out when you get to truck country

BettyZ · 05-27-2019, 03:16 PM

Quote:

Originally Posted by -ZS-Carpenter

Nope, stock height. That cap stuck up about 5"

It was hard to tell pulling in. I saw it but thought i could straddle it no problem. when i look at it from the other angle after hitting it I could see how high it really was. Need to look out when you get to truck country

Honestly, the number of things I need to watch out for on the road, especially with a Nismo, is getting to the point of absurdity. Little dips in the road, roadkill, snowballs, inclines or declines of more than .5 degrees... I've held off measuring my actual road clearance bc when I find it out, my Z may never leave the garage lol.

-ZS-Carpenter · 05-27-2019, 03:54 PM

Drive shaft, shifter, undertray, front suspension member stay all out

Just need to remove the wiring harness, crank position sensor, starter and it should be ready to drop. Barring complications or laziness the trans should be out next sunday.

Ian B · 05-27-2019, 05:22 PM

Washed her and put coverall on tires.

A Black Z34 · 05-28-2019, 01:03 AM

I, too, washed my Z and used some Woolite to tidy up the seats after a little coffee accident...stuff works wonders.

Really stuck on what test pipes to pair up with my short tails if anyone has any suggestions. YouTube hasn't helped lol

Ian B · 05-28-2019, 03:03 AM

Gonna get estimate for my rear window and quarter panel window tint redone. Previous owner had some bronze/brown looking color tint and his has bubbled lately w Texas heat.

Any suggestions how to remove old or just have installer remove and replace?

Ian B

Spooler · 05-28-2019, 09:27 AM

Quote:

Originally Posted by Ian B

Gonna get estimate for my rear window and quarter panel window tint redone. Previous owner had some bronze/brown looking color tint and his has bubbled lately w Texas heat.

Any suggestions how to remove old or just have installer remove and replace?

Ian B

Have them remove it and replace. They know all the tricks to limit any issues.

mishuko · 05-28-2019, 11:52 AM

Touched up some chips. Took some photos infront of my neighbors.

And still no exhaust. Im freakin impatient!!!

Ian B · 05-28-2019, 01:51 PM

Quote:

Originally Posted by Spooler

Have them remove it and replace. They know all the tricks to limit any issues.

Thx for info. Went by shop that did my other cars and will remove old and put new ones for $150

Ian B

redondoaveb · 05-30-2019, 08:12 PM

I got my Evo R ducts test fit. They fit nice and flush. They'll be pulled back off and painted the body color and mounted with stainless steel black powder coated button head bolts.

BettyZ · 05-30-2019, 10:03 PM

Installed the MAMS harness bar I bought on the forum and test-fit my DIY CoolShirt cooler/bracket.

Sent from my SM-G955U using Tapatalk

Rusty · 05-30-2019, 11:27 PM

Quote:

Originally Posted by redondoaveb

I got my Evo R ducts test fit. They fit nice and flush. They'll be pulled back off and painted the body color and mounted with stainless steel black powder coated button head bolts.

You going to use 3" hose for brake cooling? Don't use the orange double wall stuff. It's hard to make bends with it. With those ducts, you should have a easier time routing the hose then using the RC ducts. The RC ducts like mine are closer to the center and the right side puts the hose right into the washer reservoir.

I used the powdercoated button head bolts on mine too. Still had some rust show up in the center because the allen wrench chipped the coating inside the hole. So be warned.

You going to do the big mouth mod on the grill area too?

Rusty · 05-30-2019, 11:31 PM

Quote:

Originally Posted by BettyZ

Installed the MAMS harness bar I bought on the forum and test-fit my DIY CoolShirt cooler/bracket.

Sent from my SM-G955U using Tapatalk

Is that for your cross country trip?

redondoaveb · 05-30-2019, 11:37 PM

Quote:

Originally Posted by Rusty

You going to use 3" hose for brake cooling? Don't use the orange double wall stuff. It's hard to make bends with it. With those ducts, you should have a easier time routing the hose then using the RC ducts. The RC ducts like mine are closer to the center and the right side puts the hose right into the washer reservoir.

I used the powdercoated button head bolts on mine too. Still had some rust show up in the center because the allen wrench chipped the coating inside the hole. So be warned.

You going to do the big mouth mod on the grill area too?

I'm actually using one side to cool my oil cooler. Since my car isn't a track car I didn't feel the need for additional brake cooling but I do need more oil cooling.

My bolts are stainless steel under the powder coating. I still want to be careful not to chip the power coat.

Rusty · 05-30-2019, 11:39 PM

Quote:

Originally Posted by redondoaveb

I'm actually using one side to cool my oil cooler. Since my car isn't a track car I didn't feel the need for additional brake cooling but I do need more oil cooling.

My bolts are stainless steel under the powder coating. I still want to be careful not to chip the power coat.

Your oil cooler going to be mounted in front of the tire instead of being in front of the radiator?

05-27-2019, 03:54 PM	#3273 (permalink)
-ZS-Carpenter A True Z Fanatic Join Date: Sep 2016 Location: Illinois Posts: 2,410 Drives: 13 370z 6MT Rep Power: 2684367	Drive shaft, shifter, undertray, front suspension member stay all out Just need to remove the wiring harness, crank position sensor, starter and it should be ready to drop. Barring complications or laziness the trans should be out next sunday. JARblue, Rusty, Hotrodz and 3 others like this.

05-27-2019, 05:22 PM	#3274 (permalink)
Ian B Track Member Join Date: Mar 2011 Location: Cedar Park Posts: 679 Drives: 2010 Nissan Rep Power: 137465	Washed her and put coverall on tires. Hotrodz and old guy like this.

05-28-2019, 01:03 AM	#3275 (permalink)
A Black Z34 Base Member Join Date: Dec 2018 Location: WA Posts: 64 Drives: 16 370 Nismo Tech 6M Rep Power: 11832	I, too, washed my Z and used some Woolite to tidy up the seats after a little coffee accident...stuff works wonders. Really stuck on what test pipes to pair up with my short tails if anyone has any suggestions. YouTube hasn't helped lol old guy likes this.

05-30-2019, 10:03 PM	#3281 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 37 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	Installed the MAMS harness bar I bought on the forum and test-fit my DIY CoolShirt cooler/bracket. Sent from my SM-G955U using Tapatalk Rusty, Hotrodz, Memphis370Z and 3 others like this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[MAZOC] Official "Off-Topic" Discussion Thread	m4a1mustang	MAZOC	6670	09-06-2018 08:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10007	06-08-2017 10:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 09:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10148	06-19-2014 09:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 12:21 PM

05-28-2019, 03:03 AM	#3276 (permalink)
Ian B Track Member Join Date: Mar 2011 Location: Cedar Park Posts: 679 Drives: 2010 Nissan Rep Power: 137465	Gonna get estimate for my rear window and quarter panel window tint redone. Previous owner had some bronze/brown looking color tint and his has bubbled lately w Texas heat. Any suggestions how to remove old or just have installer remove and replace? Ian B