Hey all! Cobb is going great. Really loving my time there. With Cobb money I'm looking to add a few things to the Z this summer. My summer wishlist: -
|
|
LinkBack | Thread Tools | Display Modes |
05-27-2021, 10:23 PM | #5371 (permalink) |
Base Member
Join Date: May 2018
Location: Phoenix
Posts: 221
Drives: Slow, homie
Rep Power: 119823 |
Hey all! Cobb is going great. Really loving my time there. With Cobb money I'm looking to add a few things to the Z this summer. My summer wishlist:
- FI Resonated HFC (to pair with my FI CBE) - UpRev tune once I get the F1 Resonated HFC - SPL Bushings; any comments on what to get "first" on a DD with stock bushings all around? - ADD W1 Oil Catch Cans (a bit iffier on these, but wouldn't mind the engine dress-up and anything that contributes to preventative maintenance while I continue to upgrade the 370Z as it is daily driven; 89kmi). Does anyone have any suggestions for another manufacturer for oil catch cans? - Heat barrier wrapping my Gen3s; suffered a puncture last summer and don't want to go through that again. May be looking to replace the filters while I have them off @ ~30kmi (mostly highway), I feel like it's about time. Or do I "clean them" instead? - 25mm wheel spacers all around on stock suspension with 19" Sport Rays - Possibly a rear diffuser to complete the rear end look. Not too keen on cosmetic mods right now. Preventative maintenance and humble power gains! I am not pursuing any suspension upgrades past my current front sway bar. Waco is an unforgiving mess. Any suggestions as to what else I should be looking at for my 89kmi DD? All I have done to it besides a few cosmetics are in my signature. Cheers!
__________________
...and tomorrow I'll try again. "Prince" | F.I TDX 18" + F.I 34 Row | ZSpeed Clutch + CMAK | Stillen Gen 3 | RJM V3.3 | Hotckis Front Sway | Powertrix Spoiler Add-on | Z1 SS Lines + Hood Struts Last edited by KingZTX; 05-27-2021 at 10:28 PM. |
05-29-2021, 12:13 AM | #5372 (permalink) | |
Base Member
Join Date: May 2018
Location: Phoenix
Posts: 221
Drives: Slow, homie
Rep Power: 119823 |
[QUOTE=KapitalZ;3996719]
Quote:
I'll look into everything else! Thank you for pointing me in the right direction for SPL, it means a lot for you to take a moment to respond. Have a good one
__________________
...and tomorrow I'll try again. "Prince" | F.I TDX 18" + F.I 34 Row | ZSpeed Clutch + CMAK | Stillen Gen 3 | RJM V3.3 | Hotckis Front Sway | Powertrix Spoiler Add-on | Z1 SS Lines + Hood Struts |
|
05-29-2021, 06:25 AM | #5373 (permalink) | |
A True Z Fanatic
Join Date: Mar 2011
Location: Austin, TX
Age: 43
Posts: 36,450
Drives: 11 Z34, 98 E36 M3
Rep Power: 2684440 |
Quote:
FI HFC Ecutek > Uprev (the only benefit to Uprev is if you want to tune your car yourself) I would say don't bother with any SPL bushings at this point. Especially with the Waco roads unless you already have some failing. You can do the diff bushing if you want. Or FUCAs for ease of alignment. Catch cans are not a bad idea. Probably unnecessary though. Heat wrap is not a bad idea. Good if your IATs are excessive. Don't replace the filters unless they are in really bad shape. You should be able to clean them one way or another. Either with a recharge kit (in the case of K&N filters) or compressed air (for dry filters). If the dry filter is really dirty you can soak it in a solution of water and Simple Green (or similar) - make sure it dries completely before reinstalling. 25 mm might give a little poke in the rear so make sure you're good with that. I commonly see 15-20 mm used with the stock sport wheels. Rear diffuser
__________________
2011 370Z 6MT Sport Gun Metallic | ARC | CJM | Ecutek | FI | Fujimura | R2C | SPL | Stillen | TWM | Z1 | ZSpeed | |
|
05-30-2021, 03:27 AM | #5375 (permalink) |
Track Member
Join Date: Dec 2009
Location: Farmington, Utah
Posts: 582
Drives: 14 SR 370z 6MT
Rep Power: 10140 |
I dusted and vacuumed the inside of my Z today. Tomorrow I'm installing my HKS hi power exhaust. I bought it brand new and its got the two piece h-pipe. I'm going to be doing the job on jack stands with a friend. I'll let you guys know how it goes.
__________________
Ford Diesel and Heavy Line Technician at your service. Last edited by Dreadnaught; 05-30-2021 at 03:52 AM. |
05-30-2021, 06:15 PM | #5376 (permalink) |
Track Member
Join Date: Dec 2009
Location: Farmington, Utah
Posts: 582
Drives: 14 SR 370z 6MT
Rep Power: 10140 |
Just got done installing my HKS hi power exhaust and it fits damn near perfect! Having my friend with me helped big time since we did it while the car was on jack stands. I think the pipe that goes from the rear muffler to under the bumper cut out on the passenger side got bent just a tad too much during the build process. We just had to adjust the tip and muffler section to where no one would be able to tell. Only I know it's not 100 percent since I'm a HUGE anal head. Other than that the welds and hardware are top notch.
As far as the two piece H-pipe section it's a breeze to bolt that together. I used an open end wrench on the nut side and a ratcheting wrench from a company called Mountain on the bolt side. It's about half as tall as a shallow 3/8's drive socket on a 3/8's drive hand ratchet. Granted I'm a professional Technician and have many tools, that is the set up you need for that part. I feel like I'm driving a new car again. I love the throaty exhaust note the exhaust makes. Next for my car is the OEM black housing headlamps. Then a slight drop and then to top it off with some TE-37'S and paint. If anybody could post a picture of the wrenches from Mountain that I mentioned that would be great.
__________________
Ford Diesel and Heavy Line Technician at your service. Last edited by Dreadnaught; 06-07-2021 at 03:19 AM. |
06-04-2021, 09:40 PM | #5377 (permalink) |
A True Z Fanatic
Join Date: Apr 2017
Location: So. Commiefornia
Posts: 6,366
Drives: 2014 Nismo Gunmetal
Rep Power: 2684374 |
Installed a drain line and valve on my SOHO combo catch can. It was set up to recirculate the oil through the dipstick tube back into the oil pan. I wasn't too keen on recirculating contaminated oil back into the engine.
__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 700+whp |
06-07-2021, 11:44 AM | #5380 (permalink) |
A True Z Fanatic
Join Date: Apr 2017
Location: So. Commiefornia
Posts: 6,366
Drives: 2014 Nismo Gunmetal
Rep Power: 2684374 |
Not sure since it recirculated before so I had no way of knowing. I'll find out in September when my turbos come in.
__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 700+whp |
06-07-2021, 02:31 PM | #5381 (permalink) |
Enthusiast Member
Join Date: Jun 2011
Location: Columbia, MO
Age: 47
Posts: 460
Drives: ‘13 370Z ST 6M
Rep Power: 3428 |
I replaced the broken B-pillar finisher this weekend! I have to make sure I'm always paying attention, otherwise, it'll get expensive at $150 a pop...lol!
__________________
Zack FI catback, HFC, and Start Button - Z1 Intake - Nismo S-Tune Spoiler - PasswordJDM V2 Shift Knob |
06-09-2021, 10:29 AM | #5382 (permalink) |
A True Z Fanatic
Join Date: Jun 2014
Location: Ga
Posts: 13,830
Drives: 2013 Nismo 370z
Rep Power: 2684392 |
It won't be too bad at all. It will need to be drained frequently in the winter months due to you running E85. The drivers side always vents more moisture for some reason also. Since you are have an all in one, you won't be able to tell that.
|
06-09-2021, 10:35 AM | #5383 (permalink) |
A True Z Fanatic
Join Date: Apr 2017
Location: So. Commiefornia
Posts: 6,366
Drives: 2014 Nismo Gunmetal
Rep Power: 2684374 |
I'm going to have Specialty Z drill about a 2" hole in the Z1 undershroud so I can pop the drain hose out of the hole to make draining easier
__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 700+whp |
06-09-2021, 01:15 PM | #5384 (permalink) |
A True Z Fanatic
Join Date: Feb 2013
Location: Austin, Texas
Posts: 1,386
Drives: 11 370Z | 24 EL450
Rep Power: 64763 |
I'm waiting on my friend to print the test bracket I sent him for my Haltech dash. Other than that, just driving around and contemplating going down to 285s in the rear.
|
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[MAZOC] Official "Off-Topic" Discussion Thread | m4a1mustang | MAZOC | 6670 | 09-06-2018 08:21 PM |
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY) | AK370Z | Nissan 370Z General Discussions | 10007 | 06-08-2017 10:48 AM |
The New "What did you do with your Z today" (with off topic replies) XVIV | eastwest2300 | The Lounge (Off Topic) | 10005 | 09-11-2015 09:57 AM |
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY) | AK370Z | Nissan 370Z General Discussions | 10148 | 06-19-2014 09:20 PM |
The New "What did you do with your Z today" (with off topic replies) VIII | JARblue | The Lounge (Off Topic) | 10016 | 11-10-2013 12:21 PM |