What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

boxwood · 04-29-2020, 10:47 AM

Fluids! Diff, MT, Brake, Steering...

BettyZ · 04-29-2020, 11:59 PM

ZSpec's Ultimate Fastener Kit arrived today. Only two of the 42 provided front timing chain case/intake valve timing control cover fasteners are long enough to actually fasten anything. Not entirely pleased by this development. Shot ZSpec an email and will let you all know the response.

ABUNAI NISMO · 04-30-2020, 02:13 AM

4/29 - I had a rough day! I started at 10:00 am and got everything installed on the CJM s1.SE FRS. I pressurized the system. The pump gave me a sign. All is good! I crank the engine about 2 seconds or more. the engine roars to life! Yay! I did it!
I see gas shooting from the engine bay. I quick cut the engine and observe the issue.

I have a faulty bad pressed line from the regulator to the fuel rail. Tomorrow I will reach out to customer support and make them aware of my issue. I will also go to a shop to see if they can fabricate me a new line or somehow salvage the current one. BAD LUCK is how I will mark this one down. It happens. Other than that install was a breeze. However, lack of instructions online. I couldn't seem to find much. The install PDF from CZP where I bought it focused primarily on the fuel pump and how to fabricate it to adjust for larger pumps. PIA.

4/30 - replaced the bad line.. now with my fuel pressure at 55lbs and even trying to lower it to 50 and 45 the vehicle won’t turn over or stay running at idle.. I do believe my stock ecu mapping can’t handle the new injectors 1050cc and new pump 450 walboro. Is that the issue? spoke to specialty...I need to get towed to the shop. Stock ECU map won’t run my installed parts! May 1 - tune date set 9 am!!! Wish me the luck!

5/1 - tune day

5／3 - I went to start the vehicle today after filling up the first time with E85. It took a bit longer than usual to turn over. At times during the drive to the store...I felt a bit of hesitation in throttle response.. I just installed new injectors and fuel pump . At tune on 5/1 seemed to run really strong seemed a bit out of breathe today. Maybe it’s just me. I dunno

BettyZ · 04-30-2020, 10:53 PM

Finishing up on the ZSpec dress up kit.

Sent from my SM-G955U using Tapatalk

ABUNAI NISMO · 04-30-2020, 11:39 PM

Quote:

Originally Posted by BettyZ

Finishing up on the ZSpec dress up kit.

Sent from my SM-G955U using Tapatalk

I want one too! Hey, I have the motordyne plenum too! We are m370 bro’s

BettyZ · 05-01-2020, 12:29 AM

Quote:

Originally Posted by ABUNAI NISMO

I want one too! Hey, I have the motordyne plenum too! We are m370 bro’s

Thanks! I wish I'd bought this when I was replacing the oil gallery gaskets. Life would have been slightly less cramped.

vtec to vvel · 05-01-2020, 12:40 AM

Going to bed early tonight. Wasn't able to take my usual post-work nap, but instead, had to make 2 trips to Costco. The meat plant shutting down news is freaking me out and I ended up buying way too much meat.

Night all!

ZontheRocks · 05-01-2020, 10:05 AM

Picked up a Nismo GT500 shift knob because I *definitely* needed to spend the money.

Was looking at the Latheworks Ti Teardrop, but even with the almost double difference in weight, I just love having Nismo bits.

Just didn't find a pic of the Burnt Ti Teardrop in a 370 to convince me. Price is right, though.

abm89 · 05-01-2020, 01:55 PM

Quote:

Originally Posted by boxwood

Fluids! Diff, MT, Brake, Steering...

It's about time for me to do that as well.

theART · 05-01-2020, 03:42 PM

Maybe this weekend!

theART · 05-01-2020, 05:11 PM

Def tomorrow!

ABUNAI NISMO · 05-01-2020, 06:13 PM

We can be better but it’s a great start!!

BettyZ · 05-01-2020, 06:23 PM

Digging this no-hood look.

Sent from my SM-G955U using Tapatalk

enkei2k · 05-01-2020, 06:25 PM

Biannual fluid flush (engine, trans, diff, brake) + full tank of gas + installed Z1 SS brake lines.

ready for driving season! whenever that is

Rusty · 05-01-2020, 06:31 PM

Quote:

Originally Posted by ABUNAI NISMO

We can be better but it’s a great start!!

Good numbers, and a nice curve.

04-29-2020, 11:59 PM	#4637 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 38 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	ZSpec's Ultimate Fastener Kit arrived today. Only two of the 42 provided front timing chain case/intake valve timing control cover fasteners are long enough to actually fasten anything. Not entirely pleased by this development. Shot ZSpec an email and will let you all know the response. Rusty, Ghostvette, ZontheRocks and 1 others like this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

04-30-2020, 10:53 PM	#4639 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 38 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	Finishing up on the ZSpec dress up kit. Sent from my SM-G955U using Tapatalk JARblue, Rusty, Hotrodz and 8 others like this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

05-01-2020, 12:40 AM	#4642 (permalink)
vtec to vvel A True Z Fanatic Join Date: Feb 2015 Location: 813 Posts: 3,915 Drives: 13 Z Rep Power: 502909	Going to bed early tonight. Wasn't able to take my usual post-work nap, but instead, had to make 2 trips to Costco. The meat plant shutting down news is freaking me out and I ended up buying way too much meat. Night all! Hotrodz and ABUNAI NISMO like this. __________________ Don't like what I post? Too bad. I really don't give a sh!t

05-01-2020, 10:05 AM	#4643 (permalink)
ZontheRocks Track Member Join Date: Mar 2017 Location: Central Florida Posts: 959 Drives: 2016 Nissan PW 370Z Rep Power: 34535	Picked up a Nismo GT500 shift knob because I definitely needed to spend the money. Was looking at the Latheworks Ti Teardrop, but even with the almost double difference in weight, I just love having Nismo bits. Just didn't find a pic of the Burnt Ti Teardrop in a 370 to convince me. Price is right, though. BettyZ and ABUNAI NISMO like this. __________________ '16 Pearl White Sport \| Stillen Gen. 3 \| Motordyne ART \| Motordyne Shockwave \| ZSpeed \| Powertrix \| EVO-R \| Aeroworkz \| Nismo \| Z1 \| EcuTek \| Tuned by Seb @ SpecialtyZ

05-01-2020, 06:23 PM	#4648 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 38 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	Digging this no-hood look. Sent from my SM-G955U using Tapatalk Rusty, Hotrodz, Ghostvette and 5 others like this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

05-01-2020, 06:25 PM	#4649 (permalink)
enkei2k A True Z Fanatic Join Date: Apr 2011 Location: NYC Posts: 6,365 Drives: '12 G41 B/S M6 Rep Power: 3716	Biannual fluid flush (engine, trans, diff, brake) + full tank of gas + installed Z1 SS brake lines. ready for driving season! whenever that is Rusty, Hotrodz, old guy and 1 others like this. __________________ ...need boost...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[MAZOC] Official "Off-Topic" Discussion Thread	m4a1mustang	MAZOC	6670	09-06-2018 08:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10007	06-08-2017 10:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 09:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10148	06-19-2014 09:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 12:21 PM