Floor Jack

Jason · 03-02-2015, 09:07 AM

I'm looking for a low profile, extra long floor jack to speed up lifting the Z. Currently, I'm using a standard size hydraulic floor jack to lift each side, one at a time at the rails and then support with stands.

I would love something that is low and long enough to fit through the front of the car so that I can use the front jacking point, which would save some time by allowing me to place stands on both sides at once.

I found a promising jack here, but the length is 32.5".. When I measured from the front of the Z to the jacking point, it was a little longer than that so I'm afraid the jack won't reach the jacking point. Does anyone have any recommendations for a floor jack that'll reach and work well? The Z is stock height with the chin spoiler.

Zoren 370 · 03-02-2015, 09:58 AM

Tried that jack before and still wont reach the support brace in front the lower chin would prevent you from doing so.

The only option you have is to get 4pc of 4x4 wood. Stack in two then let the car roll over it. That would give you the clearance.

FPenvy · 03-02-2015, 10:02 AM

harbor freight has low profile jacks for under 100

I bought my 2 from here.

Floor Jacks - Save on Automotive Floor Jacks at Harbor Freight

Jason · 03-02-2015, 10:04 AM

Simple solution. Thanks!

Zoren 370 · 03-02-2015, 10:06 AM

^ Penvy actually I also tried using that still had to use wooden blocks but then again my Z is lowered. That thing weighs a ton and its huge.

I had to return it cuz I have a small garage.

Yet you cant beat that price for a huge floor jack.

FPenvy · 03-02-2015, 10:09 AM

Quote:

Originally Posted by Zoren 370

^ Penvy actually I also tried using that still had to use wooden blocks but then again my Z is lowered. That thing weighs a ton and its huge.

I had to return it cuz I have a small garage.

Yet you cant beat that price for a huge floor jack.

the 2 I have aren't that big honestly. the garage I have is 30x30 though so there's a little bit of space to work with.

I have found however that to jack the rear any jack i've had/have doesn't fit between the rear section of my exhaust lol kinda went the ghetto route of jacking up both sides then placing some block under the tires for extra support. also jack stands wherever you can find a place and still have work space in the back.

the Z is a pain to work on without a lift.

kenchan · 03-02-2015, 12:37 PM

Quote:

Originally Posted by FPenvy

harbor freight has low profile jacks for under 100

I bought my 2 from here.

Floor Jacks - Save on Automotive Floor Jacks at Harbor Freight

yah, i have 2 of the harbor freight ones myself. they've been working great.

oil the bearings on the roller from time to time as my first one seized... harbor freight gave me a replacement so i just bought a 2nd one on dat day.

Dragon_Ball_Z · 03-02-2015, 05:43 PM

Harbor freight +1

-Raj

DEpointfive0 · 03-02-2015, 05:59 PM

You gotta get the 2 ton long one. It's almost long enough to get the STUPID front jacking point. Although maybe you can if you have a stock front

onzedge · 03-02-2015, 07:08 PM

Quote:

Originally Posted by DEpointfive0

You gotta get the 2 ton long one. It's almost long enough to get the STUPID front jacking point. Although maybe you can if you have a stock front

Zbrah · 03-02-2015, 07:09 PM

Will a 3 ton be long enough? And Why do they have three different product numbers for the 3 ton from that link above?

DEpointfive0 · 03-02-2015, 10:42 PM

Quote:

Originally Posted by Zbrah

Will a 3 ton be long enough? And Why do they have three different product numbers for the 3 ton from that link above?

You want the 2 ton because it's the longest and lowest.

/thread

JARblue · 03-02-2015, 10:47 PM

I just drive one front tire of my stock height Z up onto a section of 2x12, and that is enough where I can get my low profile 3 ton jack to the front center jack point. The first couple of pumps are tight and will hit the chin spoiler if not careful, but it's the easiest method I've found.

**edit** This is the exact jack I have http://www.northerntool.com/shop/too...FQ6MaQod9EQAAw I think I may have said in another thread that I use a 23" high lift jack, but that was a different jack that belonged to someone else.

GSS138 · 03-02-2015, 11:18 PM

I have the JEGS one from amazon, low profile etc ~ 200.00+ bucks. It fits to our front jacking point almost perfectly.

axmea? · 03-03-2015, 12:55 AM

The HF low profile jack work from the front only with a low profile ramp. I jack the front about 4 - 5 notches high on my jack stands. To lift the rear, had to get to the pumpkin by driving the jack not from the rear but from the bottom center and started pumping from underneath.

03-02-2015, 09:07 AM	#1 (permalink)
Jason Enthusiast Member Join Date: May 2009 Location: Florida Posts: 309 Drives: Nissan 370Z Rep Power: 16	Floor Jack I'm looking for a low profile, extra long floor jack to speed up lifting the Z. Currently, I'm using a standard size hydraulic floor jack to lift each side, one at a time at the rails and then support with stands. I would love something that is low and long enough to fit through the front of the car so that I can use the front jacking point, which would save some time by allowing me to place stands on both sides at once. I found a promising jack here, but the length is 32.5".. When I measured from the front of the Z to the jacking point, it was a little longer than that so I'm afraid the jack won't reach the jacking point. Does anyone have any recommendations for a floor jack that'll reach and work well? The Z is stock height with the chin spoiler.

03-02-2015, 09:58 AM	#2 (permalink)
Zoren 370 A True Z Fanatic Join Date: Mar 2012 Location: FL Posts: 11,018 Drives: 11 Nissan 370 M6 Rep Power: 1913653	Tried that jack before and still wont reach the support brace in front the lower chin would prevent you from doing so. The only option you have is to get 4pc of 4x4 wood. Stack in two then let the car roll over it. That would give you the clearance. Jason likes this.

03-02-2015, 10:06 AM	#5 (permalink)
Zoren 370 A True Z Fanatic Join Date: Mar 2012 Location: FL Posts: 11,018 Drives: 11 Nissan 370 M6 Rep Power: 1913653	^ Penvy actually I also tried using that still had to use wooden blocks but then again my Z is lowered. That thing weighs a ton and its huge. I had to return it cuz I have a small garage. Yet you cant beat that price for a huge floor jack. Ommateal likes this.

03-02-2015, 05:43 PM	#8 (permalink)
Dragon_Ball_Z A True Z Fanatic Join Date: Jul 2014 Location: Mississippi Posts: 1,117 Drives: Nismo& Sport/Touring Rep Power: 17	Harbor freight +1 -Raj __________________ Build in Progress

03-02-2015, 05:59 PM	#9 (permalink)
DEpointfive0 Premium Member Bitches Join Date: Jan 2012 Location: SoCal Posts: 14,824 Drives: a lot Rep Power: 17151	You gotta get the 2 ton long one. It's almost long enough to get the STUPID front jacking point. Although maybe you can if you have a stock front onzedge likes this. __________________ Do YOU want to know what/where I got my username from? ( Click to show/hide ) NSFW due to language:

03-02-2015, 10:04 AM	#4 (permalink)
Jason Enthusiast Member Join Date: May 2009 Location: Florida Posts: 309 Drives: Nissan 370Z Rep Power: 16	Simple solution. Thanks!

03-02-2015, 07:09 PM	#11 (permalink)
Zbrah A True Z Fanatic Join Date: May 2013 Location: The370Z.com Posts: 4,956 Drives: 370Z Rep Power: 5452	Will a 3 ton be long enough? And Why do they have three different product numbers for the 3 ton from that link above? __________________

03-02-2015, 10:47 PM	#13 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	I just drive one front tire of my stock height Z up onto a section of 2x12, and that is enough where I can get my low profile 3 ton jack to the front center jack point. The first couple of pumps are tight and will hit the chin spoiler if not careful, but it's the easiest method I've found. edit This is the exact jack I have http://www.northerntool.com/shop/too...FQ6MaQod9EQAAw I think I may have said in another thread that I use a 23" high lift jack, but that was a different jack that belonged to someone else. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \| Last edited by JARblue; 03-02-2015 at 11:02 PM.

03-02-2015, 11:18 PM	#14 (permalink)
GSS138 Track Member Join Date: Mar 2013 Location: Mission Viejo, CA Posts: 769 Drives: '12 370Z 6M Sport Rep Power: 13	I have the JEGS one from amazon, low profile etc ~ 200.00+ bucks. It fits to our front jacking point almost perfectly. __________________ Current Mods: Vorpal Weapon +5.

03-03-2015, 12:55 AM	#15 (permalink)
axmea? A True Z Fanatic Join Date: Apr 2012 Location: SoCal Posts: 6,235 Drives: WELL ZED PW 6MT Rep Power: 53241	The HF low profile jack work from the front only with a low profile ramp. I jack the front about 4 - 5 notches high on my jack stands. To lift the rear, had to get to the pumpkin by driving the jack not from the rear but from the bottom center and started pumping from underneath. __________________ >MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
best floor jack for working on front and rear of 370z	gsxr750	Nissan 370Z General Discussions	35	09-12-2013 11:28 PM
Super Low Profile Floor Jack on sale for cheap	Sh0velMan	Nissan 370Z General Discussions	37	04-15-2013 09:54 AM
Actual picture of 370z supported by jack stands on all 4 side jack pionts.	gsxr750	Nissan 370Z General Discussions	2	10-28-2012 03:42 PM
[WTB] Factory 370z Floor Mats or Aftermarket all weather floor mats [SOCAL]	kday	Parts for sale (Private Classifieds)	4	06-27-2012 04:20 PM
Jack Stands / Floor Jack	ronaldr911	Exterior & Interior	31	01-10-2012 02:50 PM