How to properly jack up a nismo?

Cell · 08-22-2010, 12:30 PM

After going through the manual... it is not detailed enough to understand lol.

Does anyone have a picture of the nismo's under body and can circle where we can jack the car up? I am trying to get rid of those nasty suspension spacers...

Thank you.

fuct · 08-22-2010, 01:27 PM

there should be two little cut outs along the seam that runs on each side of the car. the jack stands go between those marks. it should be in the book.

daleks · 08-22-2010, 01:33 PM

I drive up onto 2x12 starter ramps and then fit my low profile jack under the front. There is a lift point in the middle of the front cross member. It's the little bump that sticks down.

SE · 08-22-2010, 06:01 PM

Quote:

Originally Posted by fuct

there should be two little cut outs along the seam that runs on each side of the car. the jack stands go between those marks. it should be in the book.

this

Cell · 08-23-2010, 09:19 AM

Thanks guys.

I figured it out and it seems weird for it to be lifted on that location rather than a full flat surface.

Trips · 08-23-2010, 09:32 AM

Use a slotted small piece of 2x4, make sure you slot it deep enough so the outer sides are flush with underside of the frame. This will insure you don't damage your frame rails or the jack point rails.

fuct · 08-23-2010, 10:29 AM

they sell a block at auto stores with the groove in it. i havnt seen one in awhile though.

SE · 08-23-2010, 09:36 PM

I've been meaning to post these up for sale in the vendor section but I don't have very many left.

Sooooo as a fellow Nismo owner, I'll let you guys get dibs on these.

It's been hard to jack up my car especially since it's lowered. And it's a pain in the *** to get to the pinch welds/subframe without finding 2x4's laying around the shop.

I have five sets of these in the shop. Would you guys be interested?

Cost would be about $95 shipped.

08-22-2010, 12:30 PM	#1 (permalink)
Cell A True Z Fanatic Join Date: Jan 2010 Location: Chicago Posts: 1,449 Drives: A Garbage Truck Rep Power: 21	How to properly jack up a nismo? After going through the manual... it is not detailed enough to understand lol. Does anyone have a picture of the nismo's under body and can circle where we can jack the car up? I am trying to get rid of those nasty suspension spacers... Thank you.

08-22-2010, 01:27 PM	#2 (permalink)
fuct A True Z Fanatic Join Date: May 2009 Location: Sugar Land Posts: 3,692 Drives: 97' Ranger :) Rep Power: 24	there should be two little cut outs along the seam that runs on each side of the car. the jack stands go between those marks. it should be in the book. Last edited by fuct; 08-22-2010 at 02:24 PM.

08-23-2010, 09:32 AM	#6 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,730 Drives: 🔰 Rep Power: 10	Use a slotted small piece of 2x4, make sure you slot it deep enough so the outer sides are flush with underside of the frame. This will insure you don't damage your frame rails or the jack point rails. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Anyone get the Axxess ASWC to work properly?	DeEePiDDy	Audio & Video	8	08-23-2010 09:09 PM
Fs: Pac swi-jack/boyo	specZ	Parts for sale (Private Classifieds)	4	07-27-2010 07:06 PM
New headunit. Balance/fader not working properly?	gh0st3794	Audio & Video	3	03-16-2010 04:03 PM
Jack Stands	Minicobra1	DIY Section (Do-It-Yourself)	19	03-07-2010 05:54 PM
Help me! my navi isn't working properly...	leepeen	Nissan 370Z General Discussions	4	06-02-2009 02:54 PM

08-22-2010, 01:33 PM	#3 (permalink)
daleks Enthusiast Member Join Date: Apr 2010 Location: St. Louis Posts: 424 Drives: 2011 Evo X MR Rep Power: 15	I drive up onto 2x12 starter ramps and then fit my low profile jack under the front. There is a lift point in the middle of the front cross member. It's the little bump that sticks down.

08-23-2010, 09:19 AM	#5 (permalink)
Cell A True Z Fanatic Join Date: Jan 2010 Location: Chicago Posts: 1,449 Drives: A Garbage Truck Rep Power: 21	Thanks guys. I figured it out and it seems weird for it to be lifted on that location rather than a full flat surface.

08-23-2010, 10:29 AM	#7 (permalink)
fuct A True Z Fanatic Join Date: May 2009 Location: Sugar Land Posts: 3,692 Drives: 97' Ranger :) Rep Power: 24	they sell a block at auto stores with the groove in it. i havnt seen one in awhile though.

08-23-2010, 09:36 PM	#8 (permalink)
SE A True Z Fanatic Join Date: Jan 2010 Location: San Jose, CA Posts: 4,236 Drives: 370z/STI/EVO X/IS-F Rep Power: 23	I've been meaning to post these up for sale in the vendor section but I don't have very many left. Sooooo as a fellow Nismo owner, I'll let you guys get dibs on these. It's been hard to jack up my car especially since it's lowered. And it's a pain in the *** to get to the pinch welds/subframe without finding 2x4's laying around the shop. I have five sets of these in the shop. Would you guys be interested? Cost would be about $95 shipped.