FS: 2 meth kits - brand new in box

KillerBee370

Selling these two kits for a friend.

Price S O L D ! + shipping each. Kits are brand new and in box.



email me for faster response: michael@michaelkirst.com

Here's what they are:

Aquamist 1s

The 1s is a single stage system that consists of an ERL high-pressure electro-magnetic water pump, adjustable pressure switch, plus all the necessary hardware to form the basis of a starter kit.

SYSTEM 1s

This starter kit will enable you to enter the exciting world of water injection: a high-power magnetic piston pump and a specially-designed atomizing jet form the basis of this rugged system 1. The water-pump is activated when an adjustable pressure switch, fitted to the inlet manifold, reaches its preset point: delivery rate can be altered by changing water-jet sizes.

WATER PUMP

Specially designed and manufactured by ERL for the sole purpose of pumping water, its delivery rate is small but it generates a very high pressure; a minimum differential pressure of 3 bar is necessary for the ERL atomizing jet. There are no mechanical links between the piston and the drive motor: the movement of the special magnetic stainless piston is induced by a powerful magnetic field generated by the on-board electronic controller. Flow and pressure characteristics are controlled by varying the frequency and the duration of the electrical pulse fed to the solenoid.

ADJUSTABLE PRESSURE SWITCH

This switch determines the point where the system starts to inject. It is normally fitted to the vacuum side of the inlet manifold (2D mode) for applications where load signal (throttle angle sensor) or manifold absolute pressure sensor (MAP sensor) is available. The switch is a ‘normally-closed’ type, adjustable range is between 3-30psi, factory set at 10psi. HOOD This Nitride rubber cap is for protecting the electrical contacts on the pressure switch from the harsh environment in the engine bay

STAINLESS IN-LINE WATER FILTER

Apart from performing the normal function, this filter can be back-flushed and re-used again and again. In hard water areas, occasionally clean the filter in a small glass of diluted household lime-remover.

WATER JET

The jet is made of nickel-plated brass with two spiral grooves cut into the center insert. Water travels through these grooves, acquiring a swirling motion before leaving the small hole on the tip: the main function of this arrangement is to cause an atomizing effect and turn the water into a fine mist. Of course a pressure of at least 3 bar is required. Jet sizes from 0.5mm to 1.0mm are available in 0.1mm increments. 0.5mm size is supplied with the standard kit, but alternative sizes can be supplied on request. Thread size of the jet is M8x0.75mm: this is not supplied with the kit but can be made available on a loan-and-return basis if necessary.

FUSED LOOM

(pump) The 3-wire loom is equipped with a 10A inline fuse. Wire size is very important as the pump draws large currents at start-up of every stroke (45 times/sec.): make sure a 30A wire is used if extension is necessary.

HARDWARE

All fasteners are made with high quality 316(A4) grade stainless steel: lower grade stainless steel does suffer from corrosion and pitting under the harsh environments of the engine bay HOSE The hose is made of nylon, whose natural strength can sustain pressure of over 12bar at 80°C. Lowest operating temperature is -40°C @26bars. The color supplied with the kit is semi-translucent white, but red, yellow, green, blue and black are available on request.

Race Pump Info

which pump…

We have ruled out the widely available centrifugal pump as the pumping mechanism, because it is always coupled to a high rotational-speed drive-motor for efficiency reasons, hence it is prone to wear; further problem arises when the water inside the pump is frozen, the drive motor has to be detached from the vane by a slipping clutch arrangement so drive-motor windings cannot be damaged as a result of jamming, this led to unnecessary expenses and complicated mechanical links. In addition, high speed drive motor tends to suffer from burn-out under prolonged continuous running. The ERL electro-magnetic pump In order to find a pump that will reliably perform under the harsh environment of the engine bay, we have no alternatives but to design our own. The ERL electro-magnetic pump is the result of a two-year intense mechanical and electronic research and development program. A high pressure pump with NO mechanical links, thus eliminated damages caused by jamming. The special magnetic stainless armature is set in motion by strong magnetic field induced by a powerful solenoid. Water is then delivered without being in contact with the drive-motor, pressure and delivery rate is regulated by internal high-tech electronic circuitry. How does it work?As seen form the diagram above, the construction of the center of the pump is very similar to a bicycle pump, two valves: priming- and output- valve works the same way as a bicycle pump. The similarity ends when the manual pump actions is replaced by electro-magnetic fields and speed is also cranked up to about 50 strokes a second! Water is being filled and retained between the two valves during the induction stroke (armature is pulled against the spring), water is then pushed out by the action of compressed spring and the armature when the electric-field is shut-off, high pressure is the product of spring force and the cross-section area of the armature tip. Peak pressure can go as high as 250psi!, perfectly suited the atomizing jets requirement. Electrical and Mechanical specifications Condition Input Voltage:…………………………………… 12.5V DC (absolute maximum) ………………………….. 14.3V DC

Input Current: ……………………………. 12A DC (average) (quesient current …………………………………. 10mA Control input: ………………………. 0-12v @5mA(digital)

Delivery: …………………………………….. 300cc/minute Weight: ………………………………………… 1Kg (2.2lb)

KillerBee370

Price drop bump

KillerBee370

bump

carson29

Still have these? Let me know.

KillerBee370

Sold!