Tedmeister has a reputation beyond repute

Tedmeister

Base Member

Last Activity: 06-10-2024 03:33 PM

About Me

About Tedmeister

Location

Florida

Drives

12 M6

Statistics

Total Posts

General Information

Last Activity: 06-10-2024 03:33 PM
Join Date: 02-08-2017
Referrals: 0

Friends

Showing Friends 1 to 1 of 1

Zingston

A True Z Fanatic

Likes Given

23 Likes

Tedmeister liked post by Spooler On thread : The Definitive Differential Thread

Z1 did my car back in 2017 or so. The clutch type diff will require more frequent fluid changes. That's it. You will also benefit greatly by installing a diff cooler. The diff cooler will keep the...
Liked On: 02-17-2024, 05:12 AM
Posted On: 02-15-2024, 07:35 AM
Tedmeister liked post by Averying On thread : brake squealing

You might be glazing the pads from excessive heat. I would give slotted rotors a try which should help prevent glazing by removing the topmost layer of the pads. Sent from my iPhone using...
Liked On: 07-20-2023, 04:01 AM
Posted On: 07-19-2023, 07:07 PM
Tedmeister liked post by Rusty On thread : Hard Racing Ti Brake Shields back in stock.

Hard Racing Ti Brake Shields are back in stock. They have been gone for a few years. ...
Liked On: 10-31-2022, 03:42 AM
Posted On: 10-30-2022, 05:38 PM
Tedmeister liked post by Elmo370z On thread : Forced induction

Car survived, back to the drawing board before tearing the front end off again. Coolant temps were high. IAT’s were 10 degrees over amibent, oil temps were hot but manageable . Car is wicked fast...
Liked On: 10-10-2022, 03:51 AM
Posted On: 10-09-2022, 03:04 PM
Tedmeister liked post by THE BULL On thread : new transmission

Most of the things that require break in periods are usually compounds to grind themselves flat towards the surface (clutch, LSD, brakes, engines at times) A M/T transmission will and shall...
Liked On: 10-08-2022, 04:29 AM
Posted On: 10-07-2022, 09:18 AM
Tedmeister liked post by Elmo370z On thread : Forced induction

Sebring bound tomorrow. Locked and loaded to be slow.
Liked On: 10-07-2022, 04:26 AM
Posted On: 10-06-2022, 10:51 PM
Tedmeister liked post by THE BULL On thread : oil and water Temp, WOW

Love to see someone else trying 4 inch vent ducts to feed the stock airboxes I can swear by this mod. You should look into 3.7 Q50 ones, they're bigger however might take a custom front to fit...
Liked On: 08-03-2022, 04:52 AM
Posted On: 08-02-2022, 07:20 AM
Tedmeister liked post by phunk On thread : fuel pump

Yup. That was where the venturi suction hose connected, for recovering fuel that was on the driver side of the tank. If you wanted, you could put a hose on there and run it somewhere else, such as...
Liked On: 04-13-2022, 04:34 AM
Posted On: 04-13-2022, 12:41 AM
Tedmeister liked post by Hotrodz On thread : Alternative to StopTech Sport Brake Pads

At some point you will need to make a choice between track street brakes. Endless is about as good as you will get for dual duty. Brake pads are easy to change out, so get a set for street and a set...
Liked On: 04-01-2022, 04:22 AM
Posted On: 03-31-2022, 08:21 PM
Tedmeister liked post by 2011 Nismo#91 On thread : best oil for track

This, good cooler positioning and ducting make a major difference, and a splitter too can help a lot. The stock radiator opening in general sucks for air flow, stacking coolers in front of the...
Liked On: 02-15-2022, 03:51 AM
Posted On: 02-14-2022, 05:34 AM
Tedmeister liked post by SonicVQ On thread : vvel issues

I feel your pain... This is the downside of DIY, sometimes it does cost more. :( To reduce the number of different connector that need to be purchased for manufacturing, where possible the...
Liked On: 11-12-2021, 03:36 AM
Posted On: 11-11-2021, 07:41 AM
Tedmeister liked post by HapaZ On thread : First Track Day Experience

It was a ton of fun for sure! I’m a little sad the season is over for a few months because I definitely want to get back out. I guess it’ll give me some time to get my brakes sorted out.
Liked On: 11-08-2021, 03:43 AM
Posted On: 11-07-2021, 09:17 PM
Tedmeister liked post by Elmo370z On thread : Mk60 install

This was done by Austin Hurtel.
Liked On: 09-12-2021, 05:23 AM
Posted On: 09-07-2021, 11:14 AM
Tedmeister liked post by Spooler On thread : Fyi

You are good. All of us Fast Intention turbo guys don't use a thermostatic plate either. As long as your temps are above 140 deg you are good to go.
Liked On: 08-30-2021, 04:09 AM
Posted On: 08-29-2021, 08:30 PM
Tedmeister liked post by Wigjiggy On thread : Weight Reduction

A few more weights from my 2013 370Z: OEM Hood (with trackspeck vent) 28.5lbs HVAC blower fan (behind glovebox) 5.4lbs Blower unit / heater core (behind radio/HVAC controls) 12.6lbs Dash and...
Liked On: 08-04-2021, 05:00 PM
Posted On: 08-01-2021, 04:00 PM

Page 1 of 2

Tedmeister

Base Member

About Me

Statistics

Friends

Likes Given

Mini Statistics

Friends

Group Memberships

Recent Visitors

	Zingston A True Z Fanatic