TBatt

TBatt Wrote :
Last night I found the problem. A connector was not fully seated on the transmission harness that has the hookups for the O2 sensors. There is a single wire connector that goes up near the starter motor that was not seated all of the way. When it was fixed the car started up.
--------------------
Sorry to bug you 6 years after you posted this - but i have having the same trouble (No recent work done to the car)
I checked the switch with an ohm meter and checked the fuse and the only relay i could find in the IPDM.

The wire you referred to .... where did it come from / Go to?
Thanks Tons for any help you could offer.
Dylan

PM’d you !

Crazy enough I'm in Huntsville and have been looking for a new (to me) car. I had test drove a Nismo up at Jerry Damson but it sold before I got the go ahead from my wife. I was wondering if you where available next week to meet up so that I can check out the 370. I'm Montgomery this weekend but will be back in Huntsville on Monday.

-Edward

Sorry for the slow response but I've been crazy busy at work.

Send via PayPal. My account is tbatt@knology.net

Sounds good where do I send the payment and shipping info too?

The complete kit, with shipping in the US is $175.

Hi ,
How much do you charge for your stillen idler pulley and hd belt upgrade ?

Yes, but i don't have them with me at the moment, they are at my office.

Nice car- Roll Tide ('15)!

Can you share your offsets?

I just changed the fluid in the clutch system and found out that you MUST adjust the AFP setting to 0 (turn the adjusting knob fully clockwise). Ryan put a note at the beginning of the instructions...

Unfortunately that won't work because you would be measuring the total diameter and not the wire itself. You would have to strip back the insulation to measure the wire gauge/diameter. It could also...

They look very similar but the wire gauge is larger for the gen 2 cables. The problem with the earlier ones was an intermittent connection. Very hard to test with a multi-meter. One other thing,...

They look very similar but the wire gauge is larger for the gen 2 cables. The problem with the earlier ones was an intermittent connection. Very hard to test with a multi-meter. One other thing,...

I have both and the outer skin (referred to as "snake skin") is the same nylon material.

Heat range and gap are two totally separate things. The smaller gap is needed because when the engine is under boost the air density in the combustion chamber goes up. Because air is an insulator the...

Heat range and gap are two totally separate things. The smaller gap is needed because when the engine is under boost the air density in the combustion chamber goes up. Because air is an insulator the...

With all of the things I have done to my Z the exhaust system which so sweet at first had become a drone monster. From 2K-3K rpm, the exhaust would drone at highway speeds and get really loud during...

Have you replaced the Stillen extension cables with the later version? The original cables are a known problem.

Go Ecutek with Seb at Specialty Z. The throttle response is unreal. I've got about 2500 miles now on my supercharged Z and it runs great! I was a little concerned with how it would do on cold starts...

I just ordered a Quick Jack car lift system from Ranger Automotive. Hydraulic Jack- Portable Car Lift- Race Car Lift- Race Car Jack- QuickJack...

A2A may be the better way but it is not the only way. Most all of the car makers that offer SC use a water cooled system. They offer the system as a highly developed off the shelf system. If you...

With all of the things I have done to my Z the exhaust system which so sweet at first had become a drone monster. From 2K-3K rpm, the exhaust would drone at highway speeds and get really loud during...

With all of the things I have done to my Z the exhaust system which so sweet at first had become a drone monster. From 2K-3K rpm, the exhaust would drone at highway speeds and get really loud during...

With all of the things I have done to my Z the exhaust system which so sweet at first had become a drone monster. From 2K-3K rpm, the exhaust would drone at highway speeds and get really loud during...